BS EN 160101-1998 Harmonized system of quality assessment for electronic components - Blank detail specification printed board assembly modular electronic units of assessed quality.pdf

《BS EN 160101-1998 Harmonized system of quality assessment for electronic components - Blank detail specification printed board assembly modular electronic units of assessed quality.pdf》由会员分享，可在线阅读，更多相关《BS EN 160101-1998 Harmonized system of quality assessment for electronic components - Blank detail specification printed board assembly modular electronic units of assessed quality.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 160101:1998 Harmonized system of quality assessment for electronic components Blank Detail Specification Printedboard assembly modular electronic units of assessed quality Capabilityapproval The European Standard EN160101:1998 has the status of a British Standard ICS 31.180BSE

2、N160101:1998 This British Standard, having been prepared under the directionof the Electrotechnical Sector Committee, was publishedunder the authorityofthe Standards Committee andcomes into effect on 15December1998 BSI 05-1999 ISBN 0 580 30832 4 National foreword This British Standard is the English

3、 language version of EN160101:1998 published by the European Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). The UK participation in its preparation was entrusted to Technical Committee EPL/500, Modular electronic units, which has the

4、responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UKinterests informed; monitor related international and European developments and promulgate them in the UK.

5、 A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding Europea

6、n publications. The BritishStandards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electro

7、nic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This docu

8、ment comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2 to11 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issue

9、d since publication Amd. No. Date CommentsBSEN160101:1998 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN160101 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 160101 April 1998 Descriptors: Quality, electronic components, printed boards, modular

10、electronic units English version Blank Detail Specification: Printed board assembly modular electronic units of assessed quality Capability approval Vordruck fr Bauartspezifikation: Leiterplatten, die mit Moduleinheiten derElektronik bestckt sind, mit bewerteter Qualitt Befhigungsanerkennung This Eu

11、ropean Standard was approved by CENELEC on1996-03-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referenc

12、es concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC memb

13、er into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands

14、, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC Al

15、l rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN160101:1998 EEN160101:1998 BSI 05-1999 2 Foreword This European Standard was prepared by the British ONH under the Single Originator Procedure. The text of the draft based on document CECC(Secret

16、ariat)3553 was submitted to the formal vote; together with the voting report, circulated as document CECC(Secretariat)3678, itwas approved as EN160101 on1996-03-03. The following dates were fixed: Contents Page Foreword 2 1 Introduction 3 2 Identification of the detail specification and of the PBA 3

17、 2.1 Front page of the detail specification (DS) 3 2.1.1 Standard catalogue PBA 3 2.1.2 Custom built PBA 4 2.2 Additional reference data 4 2.2.1 General 4 2.2.2 Recommended methods of handling and mounting 5 2.2.3 Functional description and range of options 5 2.2.4 recommended conditions of use (not

18、 for inspection purposes) 5 3 Supplementary information 5 3.1 Marking 5 3.2 Ordering information 5 3.3 Related documents 5 4 Inspection requirements 6 4.1 General 6 4.2 Capability approval 6 4.3 Extended capability 6 4.4 Inspection schedules 6 Annex A Recommended layout for firstpageofdetail specifi

19、cations forstandardcatalogueitems 9 Annex B Recommended layout for first pageofcustomer detail specifications notintendedforregistration 10 Annex C Recommended layout for a finalinspectionand test schedule 11 Figure 1 Maximum ratings 5 Figure 2 Example of a process flow chart foramixed technology as

20、sembly 7 latest date by which the ENhas to be implemented at national level by publication of an identical national standard or by endorsement (dop) (1998-10-15 latest date by which the national standards conflicting with the EN haveto be withdrawn (dow) 1999-10-15EN160101:1998 BSI 05-1999 3 1 Intro

21、duction 1.1 This blank detail specification is a supplementary document to sectional specification EN160100and contains requirements for style, layout and minimum content of detail specifications. 1.2 The use of this document is:- a A potential customer addresses an enquiry to the manufacturer for a

22、 printed board assembly which is within the scope of the manufacturers capability as published in the Qualified Products List CECC00200. b The customer either agrees to use a detail specification for a standard catalogue item which is listed in CECC00200in its own right and is produced by the manufa

23、cturer, or, a specification is negotiated between the manufacturer and the customer until an agreed customers detail specification is finalized. Both types of specification shall be based on the requirements of this BDS and EN160100. c The printed board assembly is inspected and released in accordan

24、ce with the agreed detail specification. 1.3 In the preparation of detail specifications, the requirements of2.4.2 and2.4.3 of EN160100 are mandatory and shall be met in full. 1.4 For the minimum content of the inspection requirements, see2.3.1 of EN160100 and4 of this BDS. 1.5 The BDS is structured

25、 in the following manner and sequence: identification of the detail specification (DS) and printed board assembly PBA (see 2) supplementary information (see 3) test schedule and inspection requirements (see4) information on application of the PBA (1.2). NOTEFor a CDS which will not be published, i.e

26、.,is not to be registered with the CECC General Secretariat, the layout requirements of this BDS, while recommended, are optional. The requirements for the content of the CDS are based on the guidelines given in EN160100,2.4.2, and are mandatory. It shall be noted that in case of a conflict between

27、a CDS and EN160100, EN 160100 shall take precedence. When requested by the customer, the CDS may be marked “Commercial-in-Confidence”. 2 Identification of the detail specification and of the PBA 2.1 Front page of the detail specification (DS) The dimensions of the layout of the front pages illustrat

28、ed in Annex A and Annex B are not mandatory. The information to be included in the DS is mandatory. 2.1.1 Standard catalogue PBA The detail specification for a standard catalogue item shall include the following information; the square brackets refer to the position on the first page layout given in

29、 Annex A of this BDS. 1 The name arid address of the National Standards Organization under whose authority the DS is published and, if different, the organization from whom the DS is available 2 The CECC symbol and the number allotted to the DS by the CECC General Secretariat 3 “EN160100” followed b

30、y the issue number and the national reference if different 4 If different from the CECC number, the national number of the DS, the date of issue and any further information required by the national system, together with any amendment numbers 5 The manufacturers type number and a brief description of

31、 the PBA or range of PBAs 6 Details of the typical construction of the PBA and any necessary cautions, e.g.,“Warning Static Sensitive Devices” (see3.1.2) or “Warning Devices containing Beryllium Oxide” or other Health and Safety Requirements For 5 and 6 the text given in the detail Specification sho

32、uld be suitable for use as an entryin CECC00200(QPL) and in CECC00300(Library List). 7 An illustration of the general outer appearance of the PBA giving main dimensions important for interchangeability or reference to the appropriate national or international documents for outline. If the critical d

33、imensions cannot be included in this drawing, the illustration may be marked “For inspection drawing(s), see Annex*”, a suitable Annex* being added to the detail specification. Whether dimensioned or not 7 shall always contain an illustration of the general outer appearance of the PBA. This can be u

34、sed to show terminations and their polarity when applicable.EN160101:1998 4 BSI 05-1999 8 Reference data giving information on the most important properties of the PBA to allow comparison between the various alternatives intended for the same or similar applications. 9 Prime electrical performance c

35、haracteristics and the climatic category of the PBA (not for inspection purposes). Where prime characteristics of electrical performance and climatic category are specified in the detail specification to be tested by the manufacturer, that manufacturer shall include such testing in the demonstration

36、 and verification of his declared capability. Additional reference data, e.g.,the range of options or the recommended conditions of use, see2.2, shall be inserted in subsequent pages of the detail specification. 2.1.2 Custom-built PBA The DS for a custom-built PBA not intended for registration in CE

37、CC00200is a customer detail specification, a CDS. It shall include the following information; the references which follow are to the position on the recommended first page layout shown in Annex B. The identity of the customer and that of the manufacturer (assembler) of the PBA shall be entered in th

38、e box identified at the top left. The specification reference on the top right of the page shall be a unique number which identifies the detail specification. The number given may be one of a series reserved for detail specification or it may be the customers order number or the manufacturers works

39、order number, provided it is prefixed so that it can be readily identified as a detail specification to EN160100. 1 “EN160100” followed by the issue number and the national reference if different 2 The customers drawing number or identification of the printed board assembly and a brief description o

40、f the PBA or range of PBAs 3 Details of typical construction of the PBA and any necessary cautions, e.g.,“Warning Static Sensitive Devices” (see3.1.2) or “Warning Devices containing Beryllium Oxide” or other Health and Safety Requirements 4 Illustration of the general outer appearance of the PBA. It

41、 may be used to show terminations and their polarity when applicable. The illustration shall give main dimensions essential for dimensioning and gauging the printed board assembly, including those important for interchangeability or shall make reference to the relevant national or international docu

42、ment for outlines. If it is not possible to show the critical dimensions here, the illustration may be marked “For inspection drawing(s), see Annex*”, a suitable Annex* being added to the DS. 5 Reference data giving information on the most important properties of the PBA to allow comparison between

43、various types intended for the same or similar applications. 6 Prime characteristics (not for inspection praises). Prime electrical performance characteristics and the climatic category of the PBA. When the ability to demonstrate and verify these is not included in the manufacturers capability, boxe

44、s5 and6 may be left blank. Where prime characteristics of electrical performance and climatic category are specified in the detail specification to be tested by the PBA manufacturer, that manufacturer shall include such testing in the demonstration and verification of his declared capability. 2.2 Ad

45、ditional reference data 2.2.1 General These data shall be inserted immediately following the front page of the detail specification. In order to define fully the build of the printed board assembly, the detail specification must specify or reference: the design authority for the PBA and the procedur

46、e for negotiating and making amendments or changes to the agreed DS the components to be incorporated (including the substrate), type, quantity and any restraints on their specification and use additional to those given in EN160100, 2.1.5 clear and precise material and component specifications that

47、comply with EN160100,2.1.5 and state the policy for component substitution or replacement whether or not a specific vendor is indicated all other materials and ancillary items required to manufacture the PBA, for example, solder resists, solders, adhesives any specific vendor(s) that shall be used f

48、or particular items circuit diagrams, assembly and detail drawings showing dimensions (stated in mm) referenced to an international drawing standard, see EN160100, 1.3, datums, machining data, finishes, component positions, polarities, style of mounting, e.g., for axial lead components, horizontal o

49、r vertical, type of fixing and, as relevant, the interconnection method to be usedEN160101:1998 BSI 05-1999 5 ancillary processes required such as the application and curing of conformal coatings test points for continuity testing when agreed all other information relevant to the build of the printed board assembly, such as alternative methods of test (providing these do not conflict with the requirements of the sectional specification), graphs, and notes necessar