BS EN 16000-2010 Plastics piping systems - Systems within the building structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning ite.pdf

《BS EN 16000-2010 Plastics piping systems - Systems within the building structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning ite.pdf》由会员分享，可在线阅读，更多相关《BS EN 16000-2010 Plastics piping systems - Systems within the building structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning ite.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 16000:2010ICS 13.220.50; 23.040.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics piping systems Systems within thebuilding structure Mounting and fixing ofcomponents in the testapparatus to thermalattack by a singleburning itemThis British Standa

2、rdwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 68716 7Amendments/corrigenda issued since publicationDate CommentsBS EN 16000:2010National forewordThis British Standard is the UK implementation of EN 16000:2010.The UK participatio

3、n in its preparation was entrusted to TechnicalCommittee PRI/88/1, Plastics piping for non-pressure applications.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Us

4、ers are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 16000:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16000 May 2010 ICS 13.220.50; 23.040.20 English Version Plastics piping systems - Systems within the bu

5、ilding structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning item Systmes de canalisations en plastique - Systmes lintrieur de la structure des btiments - Montage et fixation des composants dans lappareillage dessai une sollicitation thermique prov

6、oque par un objet isol en feuKunststoff-Rohrleitungssysteme - Systeme innerhalb der Gebudestruktur - Montage und Befestigung von Bauteilen im Prfgert fr thermische Beanspruchung durch einen einzelnen brennenden Gegenstand This European Standard was approved by CEN on 23 April 2010. CEN members are b

7、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

8、 CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same s

9、tatus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

10、gal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means

11、reserved worldwide for CEN national Members. Ref. No. EN 16000:2010: EBS EN 16000:2010EN 16000:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references . 43 Mounting and fixing of components . 4BS EN 16000:2010EN 16000:2010 (E) 3 Foreword This document (EN 16000:2010) has been prepared by

12、Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflictin

13、g national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to t

14、he CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi

15、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 16000:2010EN 16000:2010 (E) 4 1 Scope This European Standard specifies the mounting and fixing of components in the test apparatus to thermal

16、attack by a single burning item (SBI) according to EN 13823. This document is applicable to non-pressure plastics pipes, fittings and their joints intended for soil and waste applications: inside the building (application area code “B“); buried in ground within the building structure (application ar

17、ea code “BD“) and with a diameter greater than or equal to 75 mm. It is also applicable to pressure plastics pipes, fittings and their joints within the building structure: intended for water for general purposes, drainage, sewerage, as well as for any other pressure application with other fluids co

18、vered by the Construction Products Directive; hot and cold water installations for the conveyance of water and for heating systems. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.

19、For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13823:2002, Reaction to fire tests for building products Building products excluding floorings exposed to the thermal attack by a single burning item 3 Mounting and fixing of components Mount

20、ing and fixing of components in the test apparatus according to EN 13823:2002 shall conform to Figure 1 and Figure 2. If no pipes are available, testing of fittings may be done in form of a linear assembly, e.g. couplers. NOTE In case where e.g. the given dimensions do not exist the choice of dimens

21、ions and the mounting and fixing should be agreed between the manufacturer and the laboratory. BS EN 16000:2010EN 16000:2010 (E) 5 Dimensions in millimetres Key 1 Metallic bracket under socket Figure 1 Mounting and fixing of components BS EN 16000:2010EN 16000:2010 (E) 6 Dimensions in millimetres Fi

22、gure 2 Details of mounting and fixing of components BS EN 16000:2010This page has been intentionally left blank BS EN16000:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body

23、responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amend

24、ments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found o

25、n the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publi

26、cations should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of th

27、ose that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services a

28、re also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. Fo

29、r detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.

30、CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted

31、in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: