BS EN 15977-2011 Rubber or plastic coated fabrics Mechanical properties Determination of the elongation under load and the residual deformation《橡胶和塑料涂层织物 机械性能 负载和残余变形时伸长率的测定》.pdf

《BS EN 15977-2011 Rubber or plastic coated fabrics Mechanical properties Determination of the elongation under load and the residual deformation《橡胶和塑料涂层织物 机械性能 负载和残余变形时伸长率的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15977-2011 Rubber or plastic coated fabrics Mechanical properties Determination of the elongation under load and the residual deformation《橡胶和塑料涂层织物 机械性能 负载和残余变形时伸长率的测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15977:2011Rubber or plastic coated fabrics Mechanical properties Determination of theelongation under load and theresidual deformationBS EN 15977:2011 BRITISH STANDARDNatio

2、nal forewordThis British Standard is the UK implementation of EN 15977:2011. The UK participation in its preparation was entrusted to TechnicalCommittee TCI/24, Physical testing of textiles.A list of organizations represented on this committee can be obtained on request to its secretary.This publica

3、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 67968 1 ICS 59.080.40Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the

4、authority of the Standards Policy and Strategy Committee on 31 March 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 15977:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15977 February 2011 ICS 59.080.40 English Version Rubber or plastic coated fabrics - Mechanica

5、l properties - Determination of the elongation under load and the residual deformation Supports textiles revtus de caoutchouc ou de plastique - Proprits mcaniques - Dtermination de lallongement sous charge et de la dformation rsiduelle Mit Kautschuk oder Kunststoff beschichtete Textilien - Mechanisc

6、he Eigenschaften - Bestimmung der Dehnung unter Last und der verbleibenden Verformung This European Standard was approved by CEN on 8 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

7、 a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German)

8、. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, C

9、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION

10、 COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15977:2011: EBS EN 15977:2011EN 15977:2011 (E) 2 Contents Page

11、 Foreword 3Introduction .41 Scope 52 Normative references 53 Principle 54 Apparatus .55 Preparation of test specimens .66 Mechanical loading test 67 Residual deformation after heat exposure and mechanical loading (optional) 78 Calculation 89 Test report 8BS EN 15977:2011EN 15977:2011 (E) 3 Foreword

12、This document (EN 15977:2011) has been prepared by Technical Committee CEN/TC 248 “Textiles and textile products”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the la

13、test by August 2011, and conflicting national standards shall be withdrawn at the latest by August 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all s

14、uch patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungar

15、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15977:2011EN 15977:2011 (E) 4 Introduction This European Standard has been developed from the normative Annex

16、 C of EN 15619. BS EN 15977:2011EN 15977:2011 (E) 5 1 Scope This European standard describes the method of determination of the elongation under load and the residual deformation of coated fabrics. 2 Normative references The following referenced documents are indispensable for the application of thi

17、s document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12280-1:1997, Rubber- or plastics- coated fabrics Accelerated ageing tests Part 1: Heat ageing EN ISO 2231, Rubber- or plasti

18、cs-coated fabrics Standard atmospheres for conditioning and testing (ISO 2231:1989) 3 Principle Marked strips of coated fabric are loaded for a specified duration; then after relaxation, the residual deformation is calculated based on the measurements of the distance between the marks of the strip b

19、efore and after the loading stage. The appropriate testing parameters are based on the use of the coated fabrics. Test specimen can be aged by heat exposure prior to the loading stage. 4 Apparatus 4.1 Ruler, calibrated metal ruler with 0,5 mm graduated marks. 4.2 Calliper, calibrated to 0,1 mm. 4.3

20、Loading device Only a manual loading device shall be used. An automatic device shall be avoided because of the force regulation of the machine. The clamping devices shall be positioned with the centre in line with the applied force. The clamps shall be capable of holding the test specimen without al

21、lowing it to slip and designed so that they do not cut or otherwise weaken the test specimen. The clamps shall consist of two jaws of steel plate. The clamping faces shall be in the same plane. Jaws shall preferably be (70 6) mm wide, but not less than the width of the test specimen. The loads consi

22、st of calibrated masses ensuring the achievement of the determined load. 4.4 Hot air oven, according to EN 12280-1. BS EN 15977:2011EN 15977:2011 (E) 6 5 Preparation of test specimens Three strips of 50 mm width shall be tested in both directions (for example: in warp and weft direction for woven co

23、ated fabric). The length of the strips shall be at least 200 mm or 400 mm, according to the selected testing parameters as determined in Table 1. Each strip shall be prepared as follows (in order to be sure that the final strips follow exactly the direction of the yarn): Cut a strip of: a) directly

24、(50 1) mm width for coated fabrics other than woven coated fabrics, or b) 55 mm width as precisely as possible in the direction of the yarns for woven coated fabrics; then, reduce the width of the strips from 55 to (50 1) mm, by removing some yarns on both sides in order to be sure that the yarns fo

25、llow continuously the length of the sample on both sides. Two small lines (perpendicular to the length of sample) shall be marked on each strip at a distance of (100 1) mm or (200 1) mm according to the selected testing parameters as determined in Table 1. The distance between these lines shall be m

26、easured at 0,1 mm (4.2) or at 0,5 mm (4.1) see instruction in Clause 6. 6 Mechanical loading test Tests shall be carried out in atmosphere B according to EN ISO 2231. Place the test specimen in the jaws so that the distance between each marked line and its respective clamp of the loading device is 5

27、0 mm. Set the testing parameters according to Table 1. Each specimen shall be loaded under the determined load during the determined load time. Just before removing the load, the length under load shall be measured between the two marks at 0,1 mm, when using the calliper (4.2), or at 0,5 mm, when us

28、ing the ruler (4.1) in order to calculate the elongation under load. Choose the length measurement devices (4.1 or 4.2) such as the resolution represents 1/10thof the measurement of the elongation. After removing the load, each specimen shall be left on a flat surface for the determined relaxation t

29、ime without any effort before measuring the residual length between the two marks. BS EN 15977:2011EN 15977:2011 (E) 7 Table 1 Testing parameters Testing parameters Coated fabrics intended forarchitectural structure, for example Coated fabrics intended for upholstery, for example Mark distance (200

30、1) mm (100 1) mm Length of the strips at least 300 mm, plus the length in relation to the type of the clamps at least 200 mm, plus the length in relation to the type of the clamps Determined load (10,00 0,01) daN (5,00 0,01) daN Load time (24 h 30) min (30 3) min Relaxation time 2 h 5 min (30 3) min

31、 Residual deformation and under load deformation Required Required Residual deformation and under load deformation after heat exposure and mechanical loading Optional (Clause 7) Not required 7 Residual deformation after heat exposure and mechanical loading (optional) After the preparation of the tes

32、t specimens (Clause 5) and before mechanical loading test (Clause 6), the samples shall be exposed 24 h 30 min at (80 2) C in a hot air oven according to EN 12280-1:1997, method 1. After removing from the oven, each sample shall be left on a table for 2 h in order to stabilize at atmospheric conditi

33、ons before testing according to Table 1. Calculation of the residual deformation after heat exposure and mechanical loading shall be carried out in accordance with formula (2) in Clause 8. The test report shall mention that the sample has been exposed to heat before testing according to the present

34、clause of this standard. BS EN 15977:2011EN 15977:2011 (E) 8 8 Calculation The elongation under load is calculated according the following to the formula. ()00100LLLEulul= , expressed in percentage (%) at the closest 0,1 % (1) where ulE is the elongation under load, ulL is the length of the coated f

35、abric before removing the determined load, 0L is the initial length. The residual deformation is calculated according the following formula. ()00100LLLRresidual= , expressed in percentage (%) at the closest 0,1 % (2) where R is the residual deformation, residualL is the length of the coated fabric a

36、fter determined relaxation time, 0L is the initial length. 9 Test report The test report shall include the following information: a) reference to this document; b) date of the test; c) identification of the product under test; d) if the tests specimens have been aged; e) testing parameters applied (

37、mark distance, length, load, loading time, relaxation time); f) results of the test (individuals and mean values of the elongation under load, of the residual deformation); g) if required, the result of the test of the residual deformation after heat exposure and mechanical loading; h) details of an

38、y deviation that may have influenced the results. This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the internation

39、al level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make

40、sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee respo

41、nsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0

42、)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +

43、44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand int

44、ernational standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members

45、 are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British St

46、andards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright,

47、Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standar

48、d of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: