BS EN 15720-2009 Sanitary appliances - Shower trays made from impact modified coextruded ABS acrylic sheets - Requirements and test methods《卫生设备 冲击性改进的挤压ABS 丙烯酸薄板材制淋浴槽 要求和试验方法》.pdf

《BS EN 15720-2009 Sanitary appliances - Shower trays made from impact modified coextruded ABS acrylic sheets - Requirements and test methods《卫生设备 冲击性改进的挤压ABS 丙烯酸薄板材制淋浴槽 要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15720-2009 Sanitary appliances - Shower trays made from impact modified coextruded ABS acrylic sheets - Requirements and test methods《卫生设备 冲击性改进的挤压ABS 丙烯酸薄板材制淋浴槽 要求和试验方法》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 15720:2009ICS 91.140.70NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSanitary appliances Shower trays madefrom impact modifiedcoextruded ABS/acrylicsheets Requirementsand test methodsLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56

2、, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 57932 5Amendments/corrigenda issued since publicationDate CommentsBS EN 15720:2009National forewordThis British Standard is the UK i

3、mplementation of EN 15720:2009.The UK participation in its preparation was entrusted to TechnicalCommittee B/503, Sanitary appliances.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provis

4、ionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EUROPEAN STANDARD NORME EUROPENNE EU

5、ROPISCHE NORM EN 15720 December 2009 ICS 91.140.70 English Version Sanitary appliances - Shower trays made from impact modified coextruded ABS/acrylic sheets - Requirements and test methodsAppareils sanitaires - Receveurs de douche en feuilles dABS/acrylique coextrudes modifies choc - Exigences et m

6、thodes dessai Sanitrausstattungsgegenstnde - Duschwannen, hergestellt aus schlagzh-modifizierten coextrudierten ABS/Acrylplatten - Anforderungen und Prfverfahren This European Standard was approved by CEN on 7 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations w

7、hich stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European

8、 Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the nation

9、al standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Un

10、ited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15720:2009

11、: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Requirements .44.1 General 44.2 Material .44.3 Surface appearance .44.4 Waste

12、 outlet hole .44.5 Overflow hole .54.6 Hole edges 54.7 Dimensional deviations .54.8 Geometric deviations 54.8.1 General 54.8.2 Squaring .54.8.3 Straightness of the rim sides .54.8.4 Straightness of the bottom edge of the rim 54.8.5 Flatness of the top surface of rim 54.9 Bottom of the shower tray 54

13、.10 Resistance to temperature changes 64.11 Resistance to impact .64.12 Permitted deflections 64.13 Shower tray rim 65 Marking .6Annex A (normative) Shower tray test methods 7A.1 Sequence of tests 7A.2 Geometric deviations 7A.2.1 Test apparatus .7A.2.2 Squaring .7A.2.3 Straightness of the rim side .

14、8A.2.4 Straightness of the bottom edge of the rim 9A.2.5 Flatness of the top surface of the rim. 10A.3 Resistance to temperature change . 11A.3.1 Test apparatus 11A.3.2 Procedure 11A.4 Resistance to impact 12A.4.1 Test apparatus 12A.4.2 Procedure 12A.5 Determination of deflections . 12A.5.1 General

15、. 12A.5.2 Test apparatus 13A.5.3 Preloading . 13A.5.4 Deflection test 1 - Deflection of the rim and the bottom due to a load on the bottom 14A.5.5 Deflection test 2 - Deflection of the rim due to a load on the rim on the side of entry 15Bibliography . 18Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA ST

16、ANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 3 Foreword This document (EN 15720:2009) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This European Standard shall be given the status of a na

17、tional standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent r

18、ights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Attention is drawn to EN 14527 1, which has been prepared under the Mandate M/110 “Sanitary Appliances” which was given to CEN by the European Commission and the European Free Trade Association and

19、 supports the Essential Requirements to allow CE marking under Construction Products Directive (89/106/EEC). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, C

20、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHA

21、NGE CHINA STANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 4 1 Scope This European Standard specifies the requirements for shower trays for domestic purposes made from crosslinked cast acrylic sheets conforming to EN 13559 with the aim of ensuring that the pro

22、duct, when installed in accordance with the manufacturers instructions, will provide satisfactory performance in use. This European Standard is applicable to all sizes and shapes of shower trays. 2 Normative references The following referenced documents are indispensable for the application of this

23、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13559, Specifications for impact modified coextruded ABS/Acrylic sheets for baths and shower trays for domestic purposes 3 Term

24、s and definitions For the purposes of this document, the following terms and definitions apply. 3.1 domestic purposes use in homes, hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required 4 Requirements 4.1 General The manufacturer sha

25、ll provide instructions for installation and care with each shower tray. The shower tray shall be free from sharp edges that would be exposed after the installation of the shower tray in accordance with the manufacturers instructions. 4.2 Material The shower tray shall be manufactured from impact mo

26、dified coextruded ABS/acrylic sheets complying with EN 13559. 4.3 Surface appearance When the shower tray is visually inspected under strong and oblique illumination there shall be no evidence of cracks, chips, or other surface defects, such as unexpected changes in colours, etc. that will impair th

27、e appearance or performance of the shower tray. 4.4 Waste outlet hole The shower tray shall have at least one outlet hole. The dimensions of the waste outlet hole and the clearance around the waste outlet hole shall either be in accordance with the requirements of EN 251 or the manufacturer shall su

28、pply or recommend a suitable waste outlet fitting. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 5 4.5 Overflow hole When the shower tray is provided with an overflow hole the dimensions of the overflow hole and t

29、he clearance around the overflow hole shall either be in accordance with the requirements of EN 251 or the manufacturer shall supply or recommend a suitable overflow fitting. 4.6 Hole edges The edges of any holes in the shower tray shall not show evidence of chips, cracks, or any other defects that

30、may impair the appearance or performance of the shower tray. 4.7 Dimensional deviations The dimensions of shower trays shall not deviate from the size quoted by the manufacturer by greater than 5 mm. If the manufacturer states two sizes (e.g. both a work size and a nominal size) he shall state to wh

31、ich size the permitted deviations apply. For round shower trays, length and width correspond to the diameter. 4.8 Geometric deviations 4.8.1 General The straight sides or edges of the shower tray that might abut independent surroundings or supporting structures shall comply with the requirements of

32、4.8.2 to 4.8.4 and all shower trays shall comply with 4.8.5. These requirements are not applicable to sides or edges that are purposely designed as curves or slopes. 4.8.2 Squaring When tested in accordance with A.2.2 the deviation from square, q, shall be less than or equal to 5 mm. 4.8.3 Straightn

33、ess of the rim sides When tested in accordance with A.2.3 the deviation from straightness of the rim sides, s, shall be less than or equal to 5 mm. 4.8.4 Straightness of the bottom edge of the rim When tested in accordance with A.2.4 the deviation from straightness of the bottom edge of the rim, r,

34、shall be less than or equal to 5 mm. 4.8.5 Flatness of the top surface of rim When tested in accordance with A.2.5 the deviation from flatness of the top surface of the rim, c, shall be less than or equal to 5 mm. 4.9 Bottom of the shower tray When the shower tray is installed in accordance with the

35、 manufacturers instructions and the waste outlet hole is open, all water shall empty from the shower tray unless prevented by surface tension. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 6 4.10 Resistance to tem

36、perature changes When tested in accordance with A.3 the shower tray shall show no evidence of distortion or other defects which will impair the appearance or functioning of the shower tray and any deflection shall be less than or equal to 4 mm. 4.11 Resistance to impact When tested in accordance wit

37、h A.4 the bottom and the rim of the shower tray shall show no evidence of distortion or other defects that impair the appearance or functioning of the shower tray. 4.12 Permitted deflections When tested in accordance with A.5 the deflections shall be less than or equal to the values given in Table 1

38、. Table 1 Permitted deflections Test method Deflection under load a mm Residual deflection amm A.5.4 2 0,3A.5.5 4 0,3 a Values in addition to any deflection of the test rig (see A.5.2). 4.13 Shower tray rim When a shower tray is installed in accordance with the manufacturers instructions, the rim sh

39、all not encourage water to drain away from the inside of the shower tray. Roll top rims and rims incorporating special features are not subject to this requirement. 5 Marking Every shower tray shall be legibly marked on the underside with the following information: a) reference to this European Stan

40、dard (EN 15720); b) name or trademark of the manufacturer or supplier. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56, Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 7 Annex A (normative) Shower tray test methods A.1 Sequence of tests The tests shall be carried

41、out on one shower tray of each type in sequence A.2, A.3, A.5, A.4. A.2 Geometric deviations A.2.1 Test apparatus a) length measuring device with an accuracy of 0,5 mm; b) reference plane surface with flatness tolerance of 0,5 mm; c) fixed square, fixed to the reference plane surface, at least 25 mm

42、 deeper than the depth of the rim side to be measured, one arm at least 300 mm longer than the length to be measured and the other arm at least as long as the width to be measured; d) movable square, at least 25 mm deeper than the depth of the rim side to be measured, one side at least 300 mm long a

43、nd the other side at least as long as the width to be measured; e) thickness comparator or gauge with an accuracy of 0,1 mm; f) spacing rollers made of metallic material, at least 25 mm deeper than the depth of the rim side to be measured and with a diameter Dsrwith a tolerance of 0,25 mm; g) thickn

44、ess wedge with a thickness of 501,0mm. A.2.2 Squaring Place the shower tray upside down on the reference plane surface as shown in Figure A.4. Position sides AB and AD adjacent to the fixed square and place three spacing rollers with diameter Dsreach at a distance of r + 15 mm from the corners A and

45、 B, as shown in Figure A.1, where r is the radius of the corners. Measure the distance x between the corner D and the fixed square and calculate q as the difference Dsr x. Position the movable square along the side BC and place a fourth spacing roller at a distance of r + 15 mm from the corner B. Me

46、asure the distance y between the corner C and the moveable square and calculate q as the difference Dsr y. Turn the shower tray through 180 and check the distances x and y at corners A and B respectively. Record the deviation. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/04/2010 03:56,

47、Uncontrolled Copy, (c) BSIBS EN 15720:2009EN 15720:2009 (E) 8 Dimensions in millimetres 1324BCADr +15 r +15Dr+15ryxr+15srKey 1 spacing rollers 2 fixed square 3 movable square 4 shower tray r radius of the corner Dsrdiameter of spacing roller x distance between the rim and the fixed square y distance

48、 between the rim and the moveable square Figure A.1 Squaring A.2.3 Straightness of the rim side Place the shower tray upside down on the reference plane surface as shown in Figure A.4. Position two spacing rollers with diameter Dsrbetween the rim side of the shower tray and one side of the fixed squ

49、are, each at a distance of r + 15 mm from the corners, as shown in Figure A.2, where r is the radius of the corners of the shower tray. Measure the maximum and minimum distances amax and amin between the rim side and the fixed square using the thickness comparator or gauge. Calculate the deviation s as the difference amax amin. Record the deviation. Repeat the procedure for each rim of the shower tray. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS