BS EN 15534-6-2015 Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) Specifications.pdf

《BS EN 15534-6-2015 Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) Specifications.pdf》由会员分享，可在线阅读，更多相关《BS EN 15534-6-2015 Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) Specifications.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 15534-6:2015Composites made fromcellulose-based materials andthermoplastics (usually calledwood-polymer composites(WPC) or natural fibrecomposites (NFC)Part 6: Specifications for fencing profilesand elementsBS EN 15534-6:2015 BRITISH STANDARDNational forewordThis Briti

2、sh Standard is the UK implementation of EN 15534-6:2015.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/42, Fibre reinforced thermosetting plastics andprepregs.A list of organizations represented on this committee can beobtained on request to its secretary.This public

3、ation does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 85154 4ICS 79.080; 83.140.99Compliance with a British Standard cannot confer imm

4、unity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2015.Amendments issued since publicationDateT e x t a f f e c t e dBS EN 15534-6:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15534-6 September

5、2015 ICS 79.080; 83.140.99 English Version Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) - Part 6: Specifications for fencing profiles and elements Composites base de matires cellulosiques et de therm

6、oplastiques (communment appels composites bois-polymres (WPC) ou composites fibres dorigine naturelle (NFC) - Partie 6 : Spcifications relatives aux profils et lments pour cltures Verbundwerkstoffe aus cellulosehaltigen Materialien und Thermoplasten (blicherweise Holz-Polymer-Werkstoffe (WPC) oder N

7、aturfaserverbundwerkstoffe (NFC) genannt) - Teil 6: Anforderungen an Zaunprofile und -elemente This European Standard was approved by CEN on 15 August 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

8、status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French

9、, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, C

10、roatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey an

11、dUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No

12、. EN 15534-6:2015 EBS EN 15534-6:2015EN 15534-6:2015 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Requirements for fencing profiles 7 4.1 General 7 4.2 Material . 7 4.3 Appearance 7 4.4 Physical properties . 7 4.5 Mechanical properties .

13、8 4.5.1 Falling mass impact resistance 8 4.5.2 Flexural properties . 8 4.5.3 Durability of the material against biological agents 9 4.5.4 Durability of the fencing profiles against ageing and moisture . 9 4.5.5 Thermal properties . 10 4.5.6 Additional properties . 10 5 Requirements for fencing eleme

14、nts 12 6 Marking 12 Annex A (informative) Minimum frequencies of testing for factory production control purposes 14 Annex B (normative) Deformation due to the exposure to thermal radiations from the sun. 15 B.1 Principle 15 B.2 Apparatus 15 B.3 Test specimen 15 B.4 Conditioning . 15 B.5 Procedure 15

15、 B.6 Expression of the results . 16 B.7 Test report 17 Annex C (informative) Description and arrangement of infrared lamps . 18 Annex D (informative) Soft body impact test 19 D.1 Principle 19 D.2 Apparatus 19 D.3 Test specimens 20 D.4 Conditioning . 20 D.5 Procedure 20 D.6 Expression of results . 21

16、 BS EN 15534-6:2015EN 15534-6:2015 (E) 3 D.7 Test report 21 Bibliography . 22 BS EN 15534-6:2015EN 15534-6:2015 (E) 4 European foreword This document (EN 15534-6:2015) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shal

17、l be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall be withdrawn at the latest by March 2016. Attention is drawn to the possibility that some of the elements of this document

18、 may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 15534 comprises the following parts: EN 15534-1, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or

19、 natural fibre composites (NFC) Part 1: Test methods for characterization of compounds and products EN 15534-4, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 4: Specifications for decking profile

20、s and tiles EN 15534-5, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 5: Specifications for cladding profiles and tiles EN 15534-6, Composites made from cellulose-based materials and thermoplasti

21、cs (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 6: Specifications for fencing profiles and fencing elements According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European

22、Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia

23、, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15534-6:2015EN 15534-6:2015 (E) 5 1 Scope This part of EN 15534 specifies the characteristics of fencing profiles and elements made from cellulose-based materials and thermoplastics, usually called wood-polymer composites (WPC) or na

24、tural fibre composites (NFC). It is applicable to fencing profiles and elements for non-structural fencing systems. The security systems, perimeter protections, handrails and load bearing applications are out of the scope of this part of EN 15534. Any systems made from profiles in the scope of this

25、part of EN 15534 that are affected by regulations are under the responsibility of the system supplier. EN 15534-1 specifies some of the test methods relevant to this part of EN 15534. NOTE For editorial reasons, in EN 15534 the abbreviation “WPC” is used for “composites made from cellulose-based mat

26、erials and thermoplastics”. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced d

27、ocument (including any amendments) applies. EN 927-6, Paints and varnishes Coating materials and coating systems for exterior wood Part 6: Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water EN 16472, Plastics Method for artificial accelerated photoageing using me

28、dium pressure mercury vapour lamps EN 15534-1:2014, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 1: Test methods for characterisation of compounds and products EN ISO 4892-1:2000, Plastics Metho

29、ds of exposure to laboratory light sources Part 1: General guidance (ISO 4892-1:1999) EN ISO 4892-2, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps (ISO 4892-2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 15534-1:

30、2014 and the following apply. 3.1 fencing profile single profile intended to be assembled in a fencing element 3.2 fencing element assembly of two posts and one or several fencing profile(s) and possibly, fastenings and accessories BS EN 15534-6:2015EN 15534-6:2015 (E) 6 3.3 fencing system several a

31、ssembled fencing elements 3.4 bow curvature of a fencing profile across its length Note 1 to entry: see Figure 1. Key 1 bow Figure 1 Illustration of bow 3.5 cupping curvature of a fencing profile across its width Note 1 to entry: see Figure 2. Key 1 cupping Figure 2 Illustration of cupping BS EN 155

32、34-6:2015EN 15534-6:2015 (E) 7 4 Requirements for fencing profiles 4.1 General Initial type testing shall be performed to demonstrate compliance with the requirements specified in Clause 4 of this part of EN 15534. The tests according to 4.5.6 shall be carried out if the performance is to be declare

33、d by the manufacturer. Initial type testing shall be repeated, whenever a change occurs in the composition of the product, its geometry or in the production process. In case of a minor change, only the properties which could be influenced by this change shall be tested. NOTE Minimum frequencies of t

34、esting for factory production control purposes are given in Annex A. 4.2 Material The base polymer, from which the material is produced, and the type and content of cellulose-based material shall be declared by the manufacturer. Reprocessable and/or recyclable materials may be used for manufacturing

35、 profiles provided that they satisfy to the provisions of this part of EN 15534. WPC materials are recyclable materials which can be treated in a material recovery process intended to save resources while minimizing harmful emissions into air, water and soil as well as their impacts on human health.

36、 NOTE A scheme for the characterization of plastics waste is given in EN 15347 1 and guideline for the recovery and recycling are given in ISO 15270 2. 4.3 Appearance For production control purposes, the manufacturer shall compare three samples drawn at random from the same profile production batch

37、with a control sample, under the illumination conditions defined in EN 15534-1:2014, 6.1. The control samples shall be stored in a dark room and renewed every six months. If a control sample is put in contact with water, it shall be renewed immediately. 4.4 Physical properties When tested in accorda

38、nce with the test methods as specified in Table 1, using the parameters indicated, the fencing profiles, as delivered to the customer, shall have properties conforming to the requirements given in Table 1. BS EN 15534-6:2015EN 15534-6:2015 (E) 8 Table 1 Physical properties Property Requirements Test

39、 method Number of test specimens Linear mass Individual values 95 % declared value by the manufacturer. The linear mass and tolerances shall be declared by the manufacturer. EN 155341:2014, 6.5 3 specimens Thickness, width and length The relevant dimensional values and their tolerances shall be decl

40、ared by the manufacturer. EN 155341:2014, 6.6.2 3 specimens Deviation from straightness The deviation of straightness and its tolerance shall be declared by the manufacturer. EN 155341:2014, 6.6.3 3 specimens Cupping (if relevant) The cupping value and its tolerance shall be declared by the manufact

41、urer. EN 155341:2014, 6.6.4 3 specimens 4.5 Mechanical properties 4.5.1 Falling mass impact resistance When tested in accordance with the test methods as specified in Table 2, using the parameters indicated, the fencing profiles, as delivered to the customer, shall have properties conforming to the

42、requirements given in Table 2. Table 2 Falling mass impact resistance Requirements Test parameters Test method Number of test specimens Non-cellular material profiles No more than one test specimen out of 10 test specimens shall show a failure. H: (1 000 5) mm Ms: (500 2) g EN 155341:2014, 7.1.2.2.1

43、 10 specimens/faceaCellular material profiles No more than one test specimen out of 10 test specimens shall show a failure. H: (1 000 5) mm Ms: (500 2) g EN 155341:2014, 7.1.2.2.2 10 specimens/faceaaOn both faces of the fencing profile, if relevant. 4.5.2 Flexural properties When tested in accordanc

44、e with the test method as specified in Table 3, using the parameters indicated, the fencing profiles, as delivered to the customer, shall have properties conforming to the requirement given in Table 3. BS EN 15534-6:2015EN 15534-6:2015 (E) 9 Table 3 Flexural properties Requirement Test parameters Te

45、st method Number of test specimens Declaration of the modulus of elasticity in bending and the bending strength Span l1: 20 times the thickness h of the test specimen, and Span l1 100 mm. EN 155341:2014, Annex A 4 specimens/face aaOn both faces of the fencing profile, if relevant. 4.5.3 Durability o

46、f the material against biological agents For the purpose of this part of EN 15534, use classes according to the environmental conditions are defined in Table 4. Table 4 Use class and occurrence of biological agents Use classaService situation Biological agents 3 External use, above ground Basidiomyc

47、etes 4 External use, in ground contact Soft rotting micro-fungi NOTE Use classes 3 and 4 are derived from EN 335:2013 3, Table 1. aA profile may be classified in use class 3 or 4 or both. When tested in accordance with the test methods as specified in Table 5, using the parameters indicated, the mat

48、erials shall have properties conforming to the requirements given in Table 5. Table 5 Resistance against biological agents Property Requirements Test method Number of test specimens Resistance against basidiomycetes The test result shall be declared EN 155341:2014, 8.5.2 See EN 155341:2014, Table 2

49、Resistance against soft rotting micro-fungi The test result shall be declared EN 155341:2014, 8.5.3 See EN 155341:2014, Table 3 NOTE At the date of publication of this part of EN 15534, there is a lack of experience to specify requirements for these properties. 4.5.4 Durability of the fencing profiles against ageing and moisture When tested in accordance with the test methods as specified in Table 6, using the parameters indicated, the fencing profiles, as delivered to the customer, shall