BS EN 15385-2007 Packaging - Flexible laminate tubes - Test methods to determine the strength of the head welding《包装 柔性叠层管 测定头部焊接强度的试验方法》.pdf

《BS EN 15385-2007 Packaging - Flexible laminate tubes - Test methods to determine the strength of the head welding《包装 柔性叠层管 测定头部焊接强度的试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15385-2007 Packaging - Flexible laminate tubes - Test methods to determine the strength of the head welding《包装 柔性叠层管 测定头部焊接强度的试验方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58the strength of the head weldingThe European Standard EN 15385:2007 has the status of a British Sta

2、ndardICS 55.120Packaging Flexible laminate tubes Test methods to determine BRITISH STANDARDBS EN 15385:2007BS EN 15385:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 September 2007 BSI 2007ISBN 978 0 580 55647 0Amendments issued since

3、 publicationAmd. No. Date CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implementation of EN 15385:2007.The UK participation in its preparation was entrusted to Technical Committee PKW/0, Packaging.A list of

4、organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15385August 2007ICS 55.

5、120English VersionPackaging - Flexible laminate tubes - Test methods to determinethe strength of the head weldingEmballage - Tubes souples lamins - Mthodes dessaipour dterminer la rsistance de la soudure de la ttePackmittel - Laminattuben - Prfverfahren zur Bestimmungder Festigkeit der KopfnahtThis

6、European Standard was approved by CEN on 13 July 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references co

7、ncerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its ow

8、n language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania

9、, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All

10、rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15385:2007: EEN 15385:2007 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Principle 4 4 Test equipment 4 5 Test operation 5 6 Test report 6 Bibliography 7 EN 15385:2007 (E)

11、 3 Foreword This document (EN 15385:2007) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Februar

12、y 2008 and conflicting national standards shall be withdrawn at the latest by February 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Rep

13、ublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 15385:2007 (E) 4 1 Scope This European Standard spe

14、cifies a method for the determination of the strength of the head welding of flexible laminate tubes. It is applicable to flexible laminate tubes used for packing pharmaceutical, cosmetic, hygiene, food and other household products. 2 Normative references Not applicable. 3 Principle The test for the

15、 strength of the head welding is used to show whether the body laminate deforms before becoming detached from the shoulder. 4 Test equipment 4.1 Cutting device 4.2 Tensile/compression tester EN 15385:2007 (E) 5 Key 1 force meter 2 clamp 3 strip 4 tube shoulder Figure 1 Tensile strength tester 5 Test

16、 procedure a) Cut four strips of equal width (each one quarter of the circumference) from the tube body at the positions shown on Figure 2, ensuring one strip has the side seam in the centre. The cut should cover the entire length of the laminate web including the part over the shoulder. b) Pull opp

17、osing pair of strips at a speed of 130 mm/min and attempt to remove material from shoulder. c) Ensure that the material has a good weld to the shoulder. The body laminate should stretch/deform not become detached below 3 N/mm of strip width. d) Repeat for second pair of cut strips. EN 15385:2007 (E)

18、 6 Key 1 tube shoulder 2 side seam 3 strips Figure 2 Test configuration of the tube 6 Test report If not otherwise agreed between supplier and customer the test report shall contain the following information: a) reference to this European Standard, i.e. EN 15385 and, if necessary, a specification fo

19、r the method of sampling and acceptance of the batch; b) the complete identification of the batch and of the tubes checked; c) the number of tubes checked; d) the number of defects; e) the test result; f) all factors which could have affected the results or all operating details not specified in thi

20、s European Standard; g) date, place of test and name of tester. EN 15385:2007 (E) 7 Bibliography 1 EN 12374, Packaging Flexible tubes Terminology 2 EN 13461, Packaging Cylindrical flexible laminated tubes Dimensions and tolerances BS EN BSI389 Chiswick High RoadLondonW4 4AL15385:2007BSI British Stan

21、dards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Stan

22、dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technica

23、l committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standar

24、dsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standard

25、s, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exp

26、orters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards develo

27、pments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Stand

28、ards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under

29、the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implement

30、ing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.