BS EN 15200-2007 Sanitary appliances - Multifunction shower cabinets《卫生器具 多功能淋浴房》.pdf

《BS EN 15200-2007 Sanitary appliances - Multifunction shower cabinets《卫生器具 多功能淋浴房》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15200-2007 Sanitary appliances - Multifunction shower cabinets《卫生器具 多功能淋浴房》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 15200:2007Sanitary appliances Multifunction shower cabinetsICS 91.140.70g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Novemb

2、er 2009corrigendumIncorporatingNational forewordThis British Standard is the UK implementation of EN 15200:2007, incorporating corrigendum November 2009.The UK participation in its preparation was entrusted to Technical Committee B/503, Sanitary appliances.A list of organizations represented on this

3、 committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 15200:2007This B

4、ritish Standard was published under the authority of the Standards Policy and Strategy Committee on 29 June 2007 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 January 2010 Implementation of CEN corrigendum November 2009, 6.18.1(b) replacedISBN 978 0 580 68494 4EUROPEAN STAND

5、ARDNORME EUROPENNEEUROPISCHE NORMEN 15200May 2007ICS 91.140.70English VersionSanitary appliances - Multifunction shower cabinetsAppareils sanitaires - Cabines de douche multifonctions Sanitrausstattungsgegenstnde -MultifunktionsduschkabinenThis European Standard was approved by CEN on 15 March 2007.

6、CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on app

7、lication to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre h

8、as the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Port

9、ugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means re

10、servedworldwide for CEN national Members.Ref. No. EN 15200:2007: EIncorporating corrigendum November 2009EN 15200:2007 (E) 2 Contents Page Foreword5 1 Scope 6 2 Normative references 6 3 Terms and Definitions .7 4 Installation and maintenance .7 4.1 General7 4.2 Protection of drinking water quality 7

11、 4.3 Maintenance .8 5 Requirements.8 5.1 Electrical and safety 8 5.2 Dimensional deviations.8 5.3 Base 8 5.3.1 General8 5.3.2 Water Drainage.8 5.3.3 Connecting dimensions 8 5.3.4 Resistance to temperature changes8 5.3.5 Mechanical resistance.9 5.4 Walls9 5.5 Common requirements applying to base, wal

12、ls and roof .9 5.5.1 Chemical resistance 9 5.5.2 Water absorption .10 5.5.3 Steam resistance .10 5.5.4 Resistance to wet and dry cycling.10 5.5.5 Colour fastness10 5.5.6 Resistance to scratching 10 5.6 Corrosion resistance.10 5.7 Construction and design 11 5.7.1 Appearance 11 5.7.2 Waste outlet drai

13、nage .11 5.7.3 Steam outlets .11 5.7.4 Pumps .11 5.7.5 Mirrors.11 5.7.6 Components.11 5.8 Whirlpool 12 5.9 Stability .12 5.10 Endurance of doors.12 5.11 Seats .12 5.12 Grab handles12 5.13 Watertightness.12 5.13.1 Cabinet watertightness .12 5.13.2 Piping watertightness .13 5.14 Steam system.13 5.14.1

14、 Temperature increase .13 5.14.2 Temperature distribution 13 6 Test methods13 6.1 Water Drainage.13 6.2 Resistance to temperature changes13 6.2.1 Test apparatus: 13 6.2.2 Procedure (the base is submitted successively to test A and test B) .14 BS EN 15200:2007EN 15200:2007 (E) 3 6.3 Deflections under

15、 load16 6.3.1 General .16 6.3.2 Test apparatus .16 6.3.3 Preloading 16 6.3.4 Procedure.16 6.4 Resistance to impact.21 6.4.1 Test apparatus .21 6.4.2 Procedure.21 6.5 Mechanical resistance of base surface.22 6.5.1 Test apparatus .22 6.5.2 Test specimen23 6.5.3 Procedure.23 6.6 Chemical resistance24 6

16、.6.1 Test apparatus and chemicals .24 6.6.2 Test specimen25 6.6.3 Procedure.25 6.7 Water absorption .26 6.7.1 Principle26 6.7.2 Test apparatus .26 6.7.3 Test specimen28 6.7.4 Procedure.28 6.8 Steam resistance .29 6.9 Resistance to wet and dry cycling.29 6.9.1 Test apparatus .29 6.9.2 Test specimens3

17、0 6.9.3 Procedure.30 6.10 Colour fastness to hot water30 6.10.1 Apparatus.30 6.10.2 Test specimens30 6.10.3 Procedure.30 6.11 Resistance to scratching31 6.11.1 Principle31 6.11.2 Test apparatus .31 6.11.3 Test specimen31 6.11.4 Procedure.31 6.11.5 Expression of results32 6.12 Waste outlet drainage .

18、32 6.12.1 Test apparatus .32 6.12.2 Procedure.32 6.13 Stability.32 6.13.1 Test apparatus .32 6.13.2 Procedure.33 6.14 Seats .34 6.14.1 Test apparatus .34 6.14.2 Procedure.34 6.15 Grab handles34 6.15.1 Test apparatus .34 6.15.2 Procedure.34 6.16 Unit watertightness test35 6.16.1 Principle35 6.16.2 Te

19、st apparatus .35 6.16.3 Procedure.35 6.17 Piping leaktightness36 6.17.1 Test apparatus .36 6.17.2 Procedure.36 6.18 Steam heating system.36 6.18.1 Test apparatus .36 6.18.2 Procedure.36 7 Marking.37 BS EN 15200:2007EN 15200:2007 (E) 4 8 Manufacturers instructions37 Table 1 Permitted deviations 8 Tab

20、le 2 Permitted deflections of bath type base 9 Table 3 Permitted deflections of shower tray type base9 Table 4 Chemicals24 Table 5 Energy for stability test34 Figure 1 Position of the gauge15 Figure 2 Deflection test A17 Figure 3 Deflection test B18 Figure 4 Deflection test C19 Figure 5 Deflection t

21、est A20 Figure 6 Deflection test B21 Figure 7 Scratching apparatus .23 Figure 8 Cleaning device.25 Figure 9 Water absorption.26 Figure 10 Cell27 Figure 11 Clamp .28 Figure 12 Stability test arrangement33 Figure 13 - Direction of forces for grab handle test 35 BS EN 15200:2007EN 15200:2007 (E) 5 Fore

22、word This document (EN 15200:2007) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest

23、by November 2007, and conflicting national standards shall be withdrawn at the latest by November 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus

24、, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 15200:2007EN 15200:2007 (E) 6 1 Scope

25、 This standard specifies requirements and test methods for multifunction shower cabinets (subsequently referred to as unit(s), used for domestic purposes. This standard does not apply to shower cabinets and shower enclosures. NOTE For the purposes of this standard the term “domestic purposes“ includ

26、es use in hotels, accommodation for students and similar buildings, except when special provisions e. g. medical, are required. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For

27、undated references, the latest edition of the referenced document (including any amendments) applies. EN 198:1987, Specification for finished baths for domestic purposes made of acrylic material EN 200, Sanitary tapware - Single taps and combination taps (PN 10) - General technical specification EN

28、232, Baths Connecting dimensions EN 251, Shower trays Connecting dimensions EN 274-1, Waste fittings for sanitary appliances - Part 1: Requirements EN 817, Sanitary tapware Mechanical mixers (PN 10) General technical specifications EN 1111, Sanitary tapware Thermostatic mixing valves (PN 10) General

29、 technical specification EN 1112, Shower outlets for (PN 10) sanitary tapware EN 1113, Shower hoses for (PN 10) sanitary tapware EN 1286, Sanitary tapware - Low pressure mechanical mixing valves - General technical specification EN 1287, Sanitary tapware - Low pressure thermostatic mixing valves - G

30、eneral technical specifications EN 1717, Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow EN 12373-1, Aluminium and aluminium alloys - Anodizing - Part 1: Method for specifying decorative and protective anodic o

31、xidation coatings on aluminium EN 12764, Sanitary appliances Specification for whirlpool baths prEN 13618-1, Hose assembly - Flexible hose assembly - Part 1: Product standard for flexible hose assembly (with or without braiding) prEN 13618-2, Water supply - Hose assembly - Part 2: Semi-rigid hose as

32、sembly EN 13904, Low resistance shower outlets for sanitary tapware EN 13905, Low resistance shower hoses for sanitary tapware EN 14428:2004, Shower enclosures Functional requirements and test methods BS EN 15200:2007EN 15200:2007 (E) 7 EN 20105-A02, Textiles - Tests for colour fastness - Part A02:

33、Grey scale for assessing change in colour (ISO 105-A02:1993) EN 60335-2-105, Household and similar electrical appliances - Safety - Part 2-105: Particular requirements for multifunction shower cabinets (IEC 60335-2- 105:2004) EN 60730-2-8, Automatic electrical controls for household and similar use

34、Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements (IEC 60730-2-8:2000, modified) EN ISO 2409, Paints and varnishes - Cross-cut test (ISO 2409:1992) EN ISO 4892-2:2006, Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon

35、-arc lamps (ISO 4892-2:2006) ISO 4586-2:2004, High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties ISO 7892:1988, Vertical building elements Impact resistance tests Impact bodies and general test procedures 3 Terms and Definitions For the p

36、urposes of this document, the following terms and definitions apply. 3.1 multifunction shower cabinet prefabricated but not necessarily pre-assembled independent unit, comprised of a base (shower tray or bath), rigid enclosed wall(s), with or without a roof and an entry, capable of being closed to p

37、rovide a watertight compartment incorporating a showering function (mixing valve, shower head etc.) and at least one other function (e.g. steam bath, hydraulic massage, UV radiation) 3.2 shower cabinet prefabricated but not necessarily pre-assembled independent unit, comprised of a base (shower tray

38、 or bath), rigid enclosed wall(s), with or without a roof and an entry, capable of being closed to provide a watertight compartment that incorporates a showering function (mixing valve, shower head etc.) 3.3 shower enclosure arrangement of fixed or hinged panel(s) and/or door(s) erected on or around

39、 a drained shower place, shower tray or bath in conjunction with one or more walls of a building to provide a water retaining area for showering 4 Installation and maintenance 4.1 General The units shall be supplied with detailed instructions for assembly, installation and connection to electrical a

40、nd water supplies and a drainage system in accordance with the relevant national regulations, European or International Standards. NOTE 1 National regulations may require additional measures. NOTE 2 Multifunction shower cabinets can be fixed to the building to provide stability. 4.2 Protection of dr

41、inking water quality Appropriate backflow prevention devices complying with EN 1717 shall be provided. BS EN 15200:2007EN 15200:2007 (E) 8 NOTE National regulations may require additional measures. 4.3 Maintenance The manufacturer shall supply instructions for maintenance. All components of the unit

42、 requiring regular maintenance and/or replacement shall be accessible after installation. 5 Requirements 5.1 Electrical and safety Multifunction shower cabinets shall comply with EN 60335-2-105. 5.2 Dimensional deviations Dimensions of the unit shall not deviate from the size quoted by the manufactu

43、rer by more than the values given in Table 1. Table 1 Permitted deviations Dimension Permitted deviation mm Length, width 1 000 mm 5 Length, width 1 000 mm 510+Height 0105.3 Base 5.3.1 General Base testing shall be carried out with the unit installed as recommended by the manufacturer. 5.3.2 Water D

44、rainage When tested in accordance with 6.1, all water shall empty from the base of the unit unless prevented by surface tension. 5.3.3 Connecting dimensions Dimensions of the waste outlet and overflow holes shall comply with the requirements given in EN 232 or EN 251 as applicable. Other dimensions

45、are permissible if the manufacturer provides or recommends suitable fittings. 5.3.4 Resistance to temperature changes When tested in accordance with 6.2, the base shall show no evidence of distortion or other defects that will impair the units function and these deflection shall not exceed 4 mm. Exp

46、erience has proven that bases made of any plastic material passing the tests in accordance with EN 198:1987, A.3, comply with this requirement. BS EN 15200:2007EN 15200:2007 (E) 9 5.3.5 Mechanical resistance 5.3.5.1 Deflection under load When tested in accordance with 6.3, deflections of the base sh

47、all not be greater than the values given in Table 2 or in Table 3. Table 2 Permitted deflections of bath type base Test method Deflection of rim mm Deflection of bottom mm Residual deflection mm A 1 2 - B 2 3 C 4 - 0,3 Table 3 Permitted deflections of shower tray type base Test method Deflection mm

48、Residual deflection mm A 2 0,3 B 4 0,3 Experience has proven that bases made of any plastic material passing the tests in accordance with EN 198:1987, A.6, comply with this requirement. 5.3.5.2 Resistance to impact When tested in accordance with 6.4, the bottom and rim of the base shall not show any

49、 evidence of distortion or other defects which will impair appearance and/or functioning. Bases made of enamelled steel and cast iron are excluded from this test. In addition, experience has proven that bases made of any plastic material passing the tests in accordance with EN 198:1987, A.5, comply with this requirement. 5.3.5.3 Mechanical resistance of base surface When the functional surface of the base is tested in accordance with 6.5, any scratch shall not exceed 0,1 mm or the total thickness of the top la