BS EN 15169-2007 Characterization of waste - Determination of loss on ignition in waste sludge and sediments《废弃物的表征 废弃物 污泥和沉渣的烧失量的测定》.pdf

《BS EN 15169-2007 Characterization of waste - Determination of loss on ignition in waste sludge and sediments《废弃物的表征 废弃物 污泥和沉渣的烧失量的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15169-2007 Characterization of waste - Determination of loss on ignition in waste sludge and sediments《废弃物的表征 废弃物 污泥和沉渣的烧失量的测定》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 15169:2007ICS 13.030.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDCharacterization ofwaste Determinationof loss on ignitionin waste, sludge andsedimentsLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02:53, Uncontrolled Copy, (c) BSI

2、This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2009. BSI 2009ISBN 978 0 580 55086 7Amendments/corrigenda issued since publicationDate CommentsBS EN 15169:2007National forewordThis British Standard is the UK implementation of EN 15169:2007

3、.The UK participation in its preparation was entrusted to TechnicalCommittee B/508/3, Characterization of waste.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Use

4、rs are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15169Feb

5、ruary 2007ICS 13.030.40English VersionCharacterization of waste - Determination of loss on ignition inwaste, sludge and sedimentsCaractrisation des dchets - Dtermination de la perte aufeu des dchets, des boues et des sdimentsCharakterisierung von Abfall - Bestimmung desGlhverlustes in Abfall, Schlam

6、m und SedimentenThis European Standard was approved by CEN on 13 January 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibli

7、ographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of

8、a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland,

9、Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-105

10、0 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15169:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EN 15169:2007 (E) 2 Contents Page Forewor

11、d3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle5 5 Interference 5 6 Hazards .5 7 Sample preservation and preparation .5 8 Apparatus .6 9 Procedure .6 10 Expression of results 8 11 Performance characteristics 9 12 Test report 9 Annex A (informative) Summary of general req

12、uirements and recommendations .10 Annex B (informative) Additional validation data 11 B.1 General11 B.2 Type of samples and sample preparation.11 B.3 Homogeneity and stability 11 B.4 Validation data for sludge from EN 12879.12 Bibliography 13 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21

13、/10/2009 02:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EN 15169:2007 (E) 3 Foreword This document (EN 15169:2007) has been prepared by Technical Committee CEN/TC 292 “Characterization of waste”, the secretariat of which is held by NEN. This European Standard shall be given the status of a nationa

14、l standard, either by publication of an identical text or by endorsement, at the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. The method described in this standard has been derived from EN 12879 which was prepared by CEN/TC 308. Anyone de

15、aling with waste and sludge analysis should be aware of the risks of that kind of material, irrespective of the parameters to be determined. Waste and sludge samples may contain hazardous (e. g. toxic, reactive, flammable, infectious) substances, which can be prone to biological and/or chemical reac

16、tion. Consequently these samples should be handled with special care. Gases which may be produced by microbiological or chemical activity are potentially flammable and will pressurise sealed bottles. Bursting bottles are likely to result in hazardous shrapnel, dust and/or aerosol. National regulatio

17、ns should be followed with respect to all hazards associated with this method. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark

18、, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02

19、:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EN 15169:2007 (E) 4 1 Scope This European Standard specifies a method for the determination of the loss on ignition. This procedure is applicable to all kinds of waste, sludge and sediments. The loss on ignition is often used as an estimate for the cont

20、ent of non-volatile organic matter in waste, sludge and sediments. It should be noted that any content of elementary carbon and volatilisation of organic materials or chemical reactions by inorganic compounds, is included in the loss on ignition. 2 Normative references The following referenced docum

21、ents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14346, Characterisation of waste Calculation of dry matter by determination

22、of dry residue or water content 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 loss on ignition change in mass as a result of heating a sample under specified conditions. The loss on ignition is expressed in weight percent of the dry matter

23、3.2 residue on ignition mass remaining after heating a sample under specified conditions. The residue on ignition is expressed in weight percent of the dry matter 3.3 dry residue wdrremaining mass fraction of a sample after a drying process at 105 C, as specified in EN 14346 3.4 water content wwmass

24、 fraction of water in a sample determined by Karl-Fischer titration, as specified in EN 14346 3.5 dry matter wdmmass fraction of a sample excluding water expressed as a percentage by mass, calculated by determination of dry residue or water content according to EN 14346 3.6 constant mass constant ma

25、ss is obtained when the change in mass during a further period of heating of 1 h is within 0,5 % (m/m) or 2 mg, whatever is greater Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EN 15169:2007 (E) 5 4 Principle A test portion is hea

26、ted in a furnace up to (550 25) C. The difference in mass before and after the heating process is used to calculate the loss on ignition. The determination is performed on a beforehand dried sample following EN 14346 or directly on the undried sample including a drying step or by referring to the dr

27、y matter. 5 Interference In principle there are no interferences connected to the determination, as the loss on ignition is an empirical parameter. However, for many purposes the determination is used for assessing the content of organic matter in waste, sludge or sediment samples. It should be note

28、d that any elementary carbon in the sample will be included in the loss on ignition value. Furthermore, any volatilisation or chemical reactions of inorganic compounds will also be included in the loss of ignition value. NOTE 1 Chemically bound water or volatile metals (e. g. in hydroxides from flue

29、 gas cleaning processes) could be released during heating, contributing to the loss on ignition with a positive amount. NOTE 2 Iron or other metals present in the sample in the metallic state could be oxidised during heating, contributing to the loss on ignition with a negative amount. NOTE 3 Sulphi

30、des present in the sample could be oxidised to sulphate during heating, contributing to the loss on ignition with a negative amount. 6 Hazards It is advised not to store samples in the open laboratory. If samples are to be stored, this has to be done in a well ventilated place. 7 Sample preservation

31、 and preparation 7.1 Preservation When not analysed immediately samples should be stored in tight containers. For biologically inactive samples special preservation may not be necessary. Biologically active samples may need to have the lids loosened to prevent build-up of gas pressure. If samples ar

32、e known to be biologically active they should be made inactive e. g. by freezing or air drying. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EN 15169:2007 (E) 6 7.2 Preparation The samples supplied for analysis should be as homoge

33、neous as possible. Depending on the nature and appearance of the sample, different procedures can be used according EN 15002, e. g. a) Solid samples may be directly comminuted (avoiding heat) and reduced to a granular powder, preferably a particle size less than 200 m. If no volatiles are present sa

34、mples may be air-dried prior to comminuting. The drying temperature shall not exceed 40 C. b) Moist or pasty-like samples may be mixed with aluminium oxide until a granular material is obtained and then comminuted, preferably a particle size less than 200 m. In this case the ratio of aluminium oxide

35、 to sample shall be considered in the calculation of the loss on ignition. c) Liquid samples shall be homogenized immediately prior to weighing. Foreign bodies or non comminutable material (e. g. metallic parts such as nuts, bolts, scrap) should be separated from the sample and the weight and nature

36、 of the material be recorded. 8 Apparatus 8.1 Flat bottom crucible, typically 50 mm to 70 mm in diameter, suitable for heating to 550 C e. g. made of porcelain, silica, nickel or platinum. 8.2 Muffle furnace or equivalent equipment, capable of maintaining a temperature of (550 25) C. 8.3 Desiccator,

37、 containing a desiccant. 8.4 Analytical balance with an accuracy of 1 mg or better. 8.5 Metal plate. 9 Procedure 9.1 Samples not containing volatiles The determination of loss on ignition and the determination of dry matter are performed as separate operations on different portions of the same sampl

38、e. For some materials, however, it is convenient to carry out the determination of both dry residue and loss on ignition in successive operations in the same crucible. Procedure for dry residue see EN 14346. In all cases necessary precautions should be taken to avoid absorption of atmospheric humidi

39、ty by the sample until it is weighed. Prepare a crucible (8.1) by placing it in the furnace (8.2) and heat at (550 25) C for at least 20 min. Transfer the crucible from the furnace (8.2) after initial cooling on a metal plate (8.5) to a desiccator (8.3) and finish cooling to ambient temperature. Wei

40、gh the empty crucible to constant mass to the nearest 1 mg (m(a) on an analytical balance (8.4). Transfer 0,5 g to 5 g of the sample to the crucible and weigh to the nearest 1 mg (m(b). Larger masses may be taken if appropriate. NOTE 1 Masses larger than 5 g should not be used, unless it has been pr

41、oven that a complete combustion of the actual sample material can be obtained at a higher loading. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 21/10/2009 02:53, Uncontrolled Copy, (c) BSIBS EN 15169:2007EN 15169:2007 (E) 7 If the determination of loss on ignition and determination of dry

42、matter are performed in successive operations, weigh the crucible with the dried sample to the nearest 1 mg (m(d). Insert the crucible into the furnace (8.2) and heat at (550 25) C for at least 1 h. NOTE 2 If the dry matter is of high organic content, losses may occur as a result of rapid ignition o

43、r deflagration of the sample. In this case heat the sample slowly. Remove the hot crucible from the furnace (8.2) and allow cooling on a clean metal plate (8.5) for a few min. While still warm, transfer the crucible to a desiccator (8.3) and finish cooling to ambient temperature. Weigh the crucible

44、containing the ignition residue to the nearest 1 mg (m(c) as soon as ambient temperature is reached. Ignition can be regarded as complete when a constant mass is obtained. If even after a third heating at (550 25) C constant mass is not obtained, record the value determined as the last measurement.

45、This shall be recorded along with the result. NOTE 3 If black carbon particles are still present (some organic substances burn slowly at 550 C), wet the residue using a few drops of ammonium nitrate solution. After repeated drying insert the crucible into the furnace and slowly heat to avoid losses

46、by deflagration and continue heating the residue to (550 25) C. Ammonium nitrate solution is prepared by dissolving 10 g of reagent grade ammonium nitrate, NH4NO3, in 100 ml of demineralised water. 9.2 Samples containing volatiles For samples containing significant amounts of volatile components dry

47、 matter can not be determined as dry residue. In this case the dry matter is calculated from the water content. For procedure see EN 14346. In this case the loss on ignition is always performed directly on the undried sample. Prepare a crucible (8.1) by placing it in the furnace (8.2) and heat to (5

48、50 25) C for at least 20 min. Transfer the crucible from the furnace (8.2) after initial cooling on a metal plate (8.5) to a desiccator (8.3) and finish cooling to ambient temperature. Weigh the empty crucible to constant mass to the nearest 1 mg (m(a) on an analytical balance (8.4). Transfer 0,5 g

49、to 5 g of the sample to the crucible and weigh to the nearest 1 mg (m(b). Larger masses may be taken if appropriate. All necessary precautions should be taken to avoid loss of volatiles from the sample until it is weighed. NOTE 1 Masses larger than 5 g should not be used unless it has been proven that a complete combustion of the actual sample material can be obtained at a higher loading. NOTE 2 To avoid splashing from escaping vapours or sudden fire it is recommended to carefully remove most of the volatile components from the sample into a