BS EN 15167-2-2006 Ground granulated blast furnace slag for use in concrete mortar and grout - Conformity evaluation《混凝土、灰泥和薄泥浆中用粒状喷沙炉矿渣 合格评定》.pdf

《BS EN 15167-2-2006 Ground granulated blast furnace slag for use in concrete mortar and grout - Conformity evaluation《混凝土、灰泥和薄泥浆中用粒状喷沙炉矿渣 合格评定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15167-2-2006 Ground granulated blast furnace slag for use in concrete mortar and grout - Conformity evaluation《混凝土、灰泥和薄泥浆中用粒状喷沙炉矿渣 合格评定》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58and grout Part 2: Conformity evaluationThe European Standard EN 15167-2:2006 has the status of a Br

2、itish StandardICS 91.100.15Ground granulated blast furnace slag for use in concrete, mortar BRITISH STANDARDBS EN 15167-2:2006Incorporating Corrigendum No. 1BS EN 15167-2:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2006 BSI

3、 2006ISBN 0 580 48933 7certificate of conformity, issued by an EU notified body, enabling the manufacturer to issue an EC declaration of conformity and to affix the CE mark. The CE marking indicates a presumption of conformity with the minimum legal health, safety and environmental requirements in t

4、he EU members states, it is not a quality mark.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicati

5、onAmd. No. Date Comments16764 Corrigendum No. 131 October 2006 Correction to national forewordAdditional informationThis British Standard acts as a supporting standard to BS EN 15167-1, by describing the tasks required for demonstrating legal attestation of conformity to BS EN 15167-1, which is mand

6、ated by the European Commission to be specified under system of attestation of 1+, and which also make appropriate reference to this British Standard. Attestation of conformity is a legal means for demonstrating that a product meets the requirements of a harmonized European Technical Specification,

7、as defined in the Construction Products Directive (89/106/EEC). In the case of a system 1+, it is supported by an EC National forewordThis British Standard was published by BSI. It is the UK implementation of EN 15167-2:2006. Together with BS EN 15167-1, it supersedes BS 6699:1992 which will be with

8、drawn on 1 May 2008.The UK participation in its preparation was entrusted by Technical Committee B/517, Cement and lime, to Subcommittee B/517/4, Additions for concrete. A list of organizations represented on B/517/4 can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPIS

9、CHE NORMEN 15167-2August 2006ICS 91.100.15English VersionGround granulated blast furnace slag for use in concrete, mortarand grout - Part 2: Conformity evaluationLaitier granul de haut-fourneau moulu pour utilisation dansle bton, mortier et coulis - Partie 2: Evaluation de laconformitHttensandmehl z

10、ur Verwendung in Beton, Mrtel undEinpressmrtel - Teil 2: KonformittsbewertungThis European Standard was approved by CEN on 26 June 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national s

11、tandard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other

12、language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

13、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG

14、Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15167-2:2006: EEN 15167-2:2006 (E) 2 Contents Page Foreword4 1 Scope.5 2 Normative references 5 3 Terms and definitions5 4 Ta

15、sks for the manufacturer.8 4.1 Factory production control .8 4.1.1 Concept.8 4.1.2 Works quality manual .8 4.1.3 Management systems9 4.1.4 System of documentation .9 4.2 Internal quality control 10 4.2.1 Process control 10 4.2.2 Measuring and testing.10 4.2.3 Handling, storage, packaging and deliver

16、y.11 4.3 Autocontrol testing of samples 11 4.3.1 Sampling and testing.11 4.3.2 Corrective action11 4.3.3 Measuring and test equipment for autocontrol testing .11 4.3.4 Quality records.12 5 Tasks for the certification body12 5.1 General12 5.2 Surveillance, assessment and acceptance of the production

17、control .12 5.2.1 Inspection tasks .12 5.2.2 Frequency of inspections .12 5.2.3 Reports12 5.3 Evaluation of the results of autocontrol testing of samples .12 5.3.1 Evaluation tasks.12 5.3.2 Number and timing of evaluations .13 5.3.3 Control period 13 5.3.4 Evaluation of test results 13 5.3.5 Reports

18、13 5.4 Audit testing of samples taken at the factory/depot and initial type testing.13 5.4.1 Sampling .13 5.4.2 Number of samples13 5.4.3 Properties and test methods 13 5.4.4 Testing.14 5.4.5 Evaluation of test results 14 5.4.6 Reports14 5.4.7 Proficiency testing.14 5.5 Initial inspection of the fac

19、tory and the production control14 5.5.1 Inspection of a new factory.14 5.5.2 Inspection of an existing factory15 5.5.3 Criteria for the assessment of the production equipment.15 5.5.4 Criteria for the assessment of laboratories 15 5.5.5 Reports15 5.6 Evaluation of test results during the initial per

20、iod .15 5.6.1 Initial period15 5.6.2 Evaluation of test results 16 5.6.3 Reports16 EN 15167-2:2006 (E) 3 6 Actions in the event of non-conformity.16 6.1 Actions to be taken by the manufacturer 16 6.2 Actions to be taken by the certification body .16 6.2.1 Following surveillance, assessment and accep

21、tance of the production control (see 5.2) and evaluation of the results of autocontrol testing (see 5.3) .16 6.2.2 Following evaluation of the results of the audit testing of samples taken at the factory/depot (see 5.4 and Annex A)16 7 Procedure for third party certification of conformity.17 8 Certi

22、ficates of conformity and conformity mark.17 9 Requirements for dispatching centres 17 9.1 General requirements17 9.2 Tasks for the intermediary 18 9.2.1 Measures to maintain the ground granulated blastfurnace slag quality .18 9.2.2 Confirmation autocontrol testing of samples taken at the dispatchin

23、g centre.18 9.3 Tasks for the third party18 9.3.1 Surveillance, assessment and acceptance of the measures to maintain the ground granulated blastfurnace slag quality and of the confirmation autocontrol .18 9.3.2 Audit testing of samples taken at the dispatching centre.19 9.3.3 Decisions to be taken

24、19 Annex A (normative) Evaluation of the representativeness and the accuracy of the 28 day activity index test results 22 A.1 General22 A.2 Sets of results considered 22 A.3 Evaluation procedure 22 A.3.1 Introduction 22 A.3.2 Symbols 22 A.3.3 Evaluation of whether set A and set B belong to the same

25、population (sampling error check) 23 A.3.4 Comparison between set B and set C in order to check the accuracy of the autocontrol testing (testing error check).23 Bibliography 24 EN 15167-2:2006 (E) 4 Foreword This document (EN 15167-2:2006) has been prepared by Technical Committee CEN/TC 104 “Concret

26、e and related products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2007, and conflicting national standards shall be withdrawn at the latest

27、 by May 2008. The standard EN 15167, is composed of two parts: Part 1: Definitions, specifications and conformity criteria Part 2: Conformity evaluation The preparatory work was carried out by WG15 of CEN/TC 104 since November 2003 in which the following countries participated: Austria, Belgium, Cze

28、ch Republic, Finland, France, Germany, Ireland, Italy, Netherlands, Norway, Poland, Spain, Sweden, Switzerland and the United Kingdom. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Aus

29、tria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 15167-2:2006 (E) 5

30、1 Scope This European Standard specifies the scheme for the evaluation of conformity of ground granulated blastfurnace slag according to EN 15167-1. The European Standard provides technical rules for the production control by the manufacturer, including autocontrol testing of samples. It also provid

31、es rules for actions to be followed in the event of non-conformity, the procedure for the certification of conformity and requirements for dispatching centres. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only

32、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement Part 1: Determination of strength EN 196-7, Methods of testing cement Methods of taking and preparing samples of cement EN 15167-1

33、:2006, Ground granulated blast furnace slag for use in concrete, mortar and grout Part 1: Definitions, specifications and conformity criteria 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 autocontrol continual statistical quality control of

34、 the ground granulated blastfurnace slag based on the testing of samples taken by the manufacturer or their agent at point(s) of release from the ground granulated blastfurnace slag factory EN 15167-1:2006 NOTE This testing corresponds also to the “further testing of samples” mentioned in Annex III

35、Section 2 point (i) of the Construction Products Directive 89/106/EEC. 3.2 certificate of conformity document issued under the rules of a certain scheme for the evaluation of conformity indicating that adequate confidence is provided that ground granulated blastfurnace slag is in conformity with EN

36、15167-1 3.3 certification procedure by which a third party gives written assurance that a product, process or service conforms to specified requirements EN 45020:1998 EN 15167-2:2006 (E) 6 3.4 certification body impartial body, governmental or non-governmental, possessing the necessary competence an

37、d responsibility to carry out conformity certification according to given rules of procedure and management 3.5 certified ground granulated blastfurnace slag ground granulated blastfurnace slag for which a certificate of conformity has been issued NOTE A single factory can manufacture more than one

38、certified ground granulated blastfurnace slag, where each is subject to separate autocontrol and declaration of conformity. 3.6 confirmation autocontrol testing continual testing carried out by an intermediary which consists of testing of samples taken by the intermediary at the point(s) of release

39、from the dispatching centre 3.7 control period period of manufacture and dispatch identified for the evaluation of the autocontrol test results EN 15167-1:2006 3.8 conformity mark protected mark applied on the basis of the certificate of conformity (see 3.2) 3.9 depot bulk ground granulated blastfur

40、nace slag handling facility (not located at the factory) used for the dispatch of ground granulated blastfurnace slag (whether in bulk or bagged) after transfer or storage where the manufacturer has full responsibility for all aspects of the quality of the ground granulated blastfurnace slag 3.10 di

41、spatching centre bulk ground granulated blastfurnace slag handling facility (not located at the factory) used for the dispatch of ground granulated blastfurnace slag after transfer or storage where an intermediary has full responsibility for all aspects of the quality of the ground granulated blastf

42、urnace slag 3.11 existing factory factory which is already producing ground granulated blastfurnace slag certified under this scheme 3.12 factory production control permanent internal control of ground granulated blastfurnace slag production exercised by the manufacturer consisting of internal quali

43、ty control and autocontrol testing 3.13 factory facility used by a manufacturer for the production of ground granulated blastfurnace slag using equipment which is suitable for continuous mass production of ground granulated blastfurnace slag, in particular equipment for adequate grinding and homogen

44、isation and the necessary silo capacity for the storage and dispatch of each ground granulated blastfurnace slag produced. This equipment and the production control applied allow the control of production with sufficient accuracy to ensure that the requirements of EN 15167-1 are met EN 15167-2:2006

45、(E) 7 3.14 initial period immediate period after the first issuing of the certificate of conformity for a ground granulated blastfurnace slag 3.15 inspection body impartial body having the organization, staffing, competence and integrity to perform according to specified criteria functions such as a

46、ssessing, recommending for acceptance and subsequent audit of manufacturers quality control operations, and selection and evaluation of products on site or in factories or elsewhere, according to specific criteria Construction Products Directive, 89/106/EEC 3.16 intermediary natural or legal person

47、who takes from the manufacturer ground granulated blastfurnace slag certified according to EN 15167-2 and bearing the conformity mark, who undertakes full responsibility for maintaining in a dispatching centre all aspects of the quality of the ground granulated blastfurnace slag and who supplies the

48、 ground granulated blastfurnace slag onwards to a further natural or legal person 3.17 manufacturer operator of the factory 3.18 new factory factory which is not already producing ground granulated blastfurnace slag certified under this scheme 3.19 quality control operational techniques and activiti

49、es that are used to fulfil requirements for quality 3.20 single result limit value value of a mechanical, physical or chemical property which for any single test result in the case of an upper limit is not to be exceeded or in the case of a lower limit is, as a minimum, to be reached EN 15167-1:2006 3.21 specified characteristic value characteristic value of a chemical or physical property which in the case of an upper limit is not to be exceeded or in the case of a lower limit is, as a minimum, to be reached EN