BS EN 14988-2017 Childrens high chairs Requirements and test methods《儿童用高脚椅子 要求和试验方法》.pdf

《BS EN 14988-2017 Childrens high chairs Requirements and test methods《儿童用高脚椅子 要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14988-2017 Childrens high chairs Requirements and test methods《儿童用高脚椅子 要求和试验方法》.pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、Childrens high chairs - Requirements and test methodsBS EN 14988:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14988 July 2017 ICS 97.140; 97.190 Supersedes EN 14988-1:2006+A1:2012, EN 14988-2:2006+A1:2012Eng

2、lish Version Childrens high chairs - Requirements and test methods Chaises hautes pour enfants - Exigences et mthodes dessai Kinderhochsthle - Anforderungen und PrfverfahrenThis European Standard was approved by CEN on 24 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regu

3、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN memb

4、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. C

5、EN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

6、 Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploita

7、tion in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14988:2017 ENational forewordThis British Standard is the UK implementation of EN 14988:2017. It supersedes BS EN 149882:2006+A1:2012 and BS EN 149881:2006+A1:2012, which are withdrawn.The UK participation in

8、its preparation was entrusted to Technical Committee CW/1, Safety of child use and child care products.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are

9、responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 90544 5ICS 97.190; 97.140Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of t

10、he Standards Policy and Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 14988:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14988 July 2017 ICS 97.140; 97.190 Supersedes EN 14988-1:2006+A1:2012, EN 14988-2:2006+A1:20

11、12English Version Childrens high chairs - Requirements and test methods Chaises hautes pour enfants - Exigences et mthodes dessai Kinderhochsthle - Anforderungen und PrfverfahrenThis European Standard was approved by CEN on 24 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal

12、 Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

13、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versio

14、ns. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Po

15、land, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exp

16、loitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14988:2017 EBS EN 14988:2017EN 14988:2017 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 General 6 4.1 Test conditions . 6 4.2 Application of fo

17、rces 6 4.3 Tolerances . 6 4.4 Test sequence . 7 4.5 Determination of the junction line . 7 5 Test equipment 8 5.1 General 8 5.2 Test mass A 8 5.3 Impact hammer 8 5.4 Large loading pad 9 5.5 Small loading pad 9 5.6 Stops 10 5.7 Floor surface 10 5.8 Beams . 10 5.9 Probes for finger entrapment 10 5.10

18、Test mass B . 10 5.11 Small parts cylinder 10 5.12 Small torso probe . 11 5.13 Test mass C . 11 5.14 Leg probe . 12 5.15 Wedge block . 12 5.16 Large head probe . 13 5.17 Impactor 14 5.18 Wood block . 14 5.19 Feeler gauge . 14 5.20 Test mass D . 14 6 Chemical hazards - Migration of certain elements (

19、see A.2) 14 7 Thermal hazards (see A.3) 15 8 Mechanical hazards (see A.4) 15 8.1 Hazards caused by folding of the product . 15 8.2 Hazards caused by height adjustment 16 8.3 Entrapment hazards (see A.4.1) . 17 8.4 Hazards caused by moving parts (see A.4.2) 18 8.5 Entanglement hazards (see A.4.3) . 1

20、8 8.6 Choking and ingestion hazards (see A.4.4) . 19 8.7 Hazards caused by edges, corners and protruding parts (see A.4.6) 21 8.8 Strength and durability hazards (Structural integrity, see A.4.7) 21 8.9 Hazards from falls out of the high chair (see A.4.8) . 24 8.10 Suffocation hazards (see A.4.5) .

21、32 BS EN 14988:2017EN 14988:2017 (E) 3 8.11 Castors and wheels (see A.4.9) 32 8.12 Stability (see A.A.4.10) 34 9 Marking and product information 38 9.1 General . 38 9.2 Marking 38 9.3 Instructions for use 39 9.4 Purchase information . 39 Annex A (informative) Rationales . 41 A.1 Introduction 41 A.2

22、Chemical hazards (see Clause 6) . 41 A.3 Thermal hazards (see Clause 7) 41 A.4 Mechanical hazards (see Clause 8) . 41 Annex B (informative) A- deviations 44 Annex C (normative) Translations 46 Bibliography . 56 BS EN 14988:2017EN 14988:2017 (E) 4 European foreword This document (EN 14988:2017) has b

23、een prepared by Technical Committee CEN/TC 364 “High Chairs“, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2018, and conflicting national standa

24、rds shall be withdrawn at the latest by July 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14988-1:2006+A1:2012 a

25、nd EN 14988-2:2006+A1:2012. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This document contains the following main modifications in comparison to the previous versions: EN 14988-1:2006+A1:2012 and EN 14988-2:2006+A1:

26、2012 have been merged into one single document; complete review of the standard in a hazard base format; modifications necessary to comply with European Decision 2013/121/EU; addition of a dynamic strength test; inclusion of specific requirements for high chair with more than two castors/wheels; imp

27、rovement of restraint system requirements to require a passive crotch restraint for products with a horizontal component in front of the baby. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Stand

28、ard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slove

29、nia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14988:2017EN 14988:2017 (E) 5 1 Scope This European Standard specifies safety requirements for free standing childrens high chairs that elevate children to dining table height usually for the purposes of feeding or eating. Childre

30、ns high chairs are for children up to 3 years of age who are capable of sitting unaided. With the exception of special high chairs for medical purposes, this standard applies to childrens high chairs for domestic and non-domestic use. NOTE If a childrens high chair has to or can be converted into ot

31、her functions, additional European Standards may apply. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest

32、 edition of the referenced document (including any amendments) applies. EN 71-2:2011+A1:2014, Safety of toys - Part 2: Flammability EN 71-3, Safety of toys - Part 3: Migration of certain elements EN 13210, Child use and care articles - Childrens harnesses, reins and similar type articles - Safety re

33、quirements and test methods ISO 7619-1, Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Durometer method (Shore hardness) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 active restraint system system whe

34、re the carer performs an action to ensure that the child is secured in the restraint system 3.2 passive restraint system system where the carer does not perform an action to ensure that the child is secured in the restraint system 3.3 crotch restraint device passing between the legs of the child and

35、 preventing the child from slipping forwards out of the high chair 3.4 waist restraint rigid or flexible device(s), which when fastened, goes from one side of the high chair to the other passing in front of the childs waist or surrounding the childs waist 3.5 shoulder restraint device passing over t

36、he shoulders and connecting either to the crotch restraint or to the waist restraint BS EN 14988:2017EN 14988:2017 (E) 6 3.6 locking device component that maintains part(s) of the product in the position of use EXAMPLE Latch, a hook, an over centre lock. 3.7 operating device part of the locking mech

37、anism(s) or parking device(s) designed to be activated by the carer by one or several action(s) 3.8 parking device device intended to prevent rolling of castors/wheels 3.9 locking mechanism assembly consisting of one or more locking device(s) and one or more operating device(s) 3.10 junction line in

38、tersection of the seat and the back rest 4 General 4.1 Test conditions The high chair shall be tested as delivered. If the high chair is a knock-down type, it shall be assembled according to the instructions supplied with it. If the instructions allow for different adjustments or configurations of c

39、omponents (e.g. inclination of the backrest, height of the seat, position of the tray, position of castors/wheels, etc.), the most onerous combination shall be used for each test, unless otherwise specified in the test method. Knock-down fittings shall be tightened before testing. Further re-tighten

40、ing shall not take place. 4.2 Application of forces The forces in the static load tests shall be applied sufficiently slowly to ensure that negligible dynamic force is applied. The tests are described in terms of the application of forces, however masses can be used. The relationship 10 N = 1 kg sha

41、ll be used for this purpose. 4.3 Tolerances Unless otherwise stated, the following tolerances apply: Forces: 5 % of the nominal force; Masses: 0,5 % of the nominal mass; Dimensions: 1,0 mm of the nominal dimension; Angles: 2 of the nominal angle; Positioning of loading pads: 5 mm. BS EN 14988:2017EN

42、 14988:2017 (E) 7 NOTE For the purposes of uncertainty in measurements, test results are not considered to be adversely affected when the above tolerances are met. 4.4 Test sequence The tests in Clause 8 shall be carried out on the same high chair and in the order of the clauses of this standard. 4.

43、5 Determination of the junction line The junction line is shown in Figure 1 below. Where the backrest and the seat do not meet, the junction line is the projection of the backrest onto the seat (see Figure 1). Key LL junction line 1 backrest 2 seat Figure 1 Junction line When the seat unit is in the

44、 form of a hammock, a theoretical junction line, “LL”, shall be determined as shown in Figure 2. The junction line may vary when the backrest is adjusted in different positions. Key AA top edge of the backrest BB front edge of the seat LL junction line CL vertical projection of C on the hammock C mi

45、d-point between A and B Figure 2 Junction line for seat units in the form of a hammock BS EN 14988:2017EN 14988:2017 (E) 8 5 Test equipment 5.1 General Unless otherwise specified, test forces may be applied by any suitable device as results are dependent only upon correctly applied forces and not up

46、on the apparatus. 5.2 Test mass A A rigid cylinder 200 mm in diameter and 300 mm in height, having a mass of 15 kg with its centre of gravity 150 mm above its base. The edges shall have a radius of 5 mm. Two anchorage points shall be provided. These shall be positioned 150 mm from the base and at an

47、 angle of 180 to each other around the circumference (see Figure 3). Dimensions in millimetres Key 1 edge radius: (5 1) mm 2 anchorage points Figure 3 Test mass A 5.3 Impact hammer A striker in the form of a cylindrical object having a total mass of 6,5 kg supported from a pivot by a steel tube of 3

48、8 mm in diameter and with a wall thickness of 2 mm (see Figure 4). The distance between the pivot and the centre of gravity of the striker shall be 1 000 mm. The pendulum arm shall be pivoted by a low friction bearing. BS EN 14988:2017EN 14988:2017 (E) 9 Dimensions in millimetres Key 1 pendulum head

49、, steel mass 6,4 kg 2 hardwood 3 rubber 50 10 Shore A (ISO 7619-1) 4 pendulum arm, length 950 mm; high tensile steel tube 38 mm x 2 mm; mass (2 0,2) kg 5 pivot point Mass of assembly (Key numbers 1, 2 and 3): (6,5 0,07) kg Figure 4 Impact hammer 5.4 Large loading pad A rigid cylindrical object 100 mm in diameter having a smooth hard surface and edges rounded with radius of 12 mm. 5.5 Small loading pad A rigid cylindrical object 30 mm in diameter having a smooth hard surface and edges rounded with radius