BS EN 14954-2005 Surfaces for sports areas - Determination of hardness of natural turf and unbound mineral surfaces for outdoor sports areas《运动场地表面 室外运动场天然草皮和散矿渣地表面的硬度测定》.pdf

《BS EN 14954-2005 Surfaces for sports areas - Determination of hardness of natural turf and unbound mineral surfaces for outdoor sports areas《运动场地表面 室外运动场天然草皮和散矿渣地表面的硬度测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14954-2005 Surfaces for sports areas - Determination of hardness of natural turf and unbound mineral surfaces for outdoor sports areas《运动场地表面 室外运动场天然草皮和散矿渣地表面的硬度测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58turf and unbound mineral surfaces for outdoor sports areasThe European Standard EN 14954:2005 has t

2、he status of a British StandardICS 97.220.10Surfaces for sports areas Determination of hardness of natural BRITISH STANDARDBS EN 14954:2005BS EN 14954:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 26 November 2005 BSI 26 November 2005IS

3、BN 0 580 47316 3The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or

4、of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises

5、 a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this committee can b

6、e obtained on request to its secretary.Cross-referencesenquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard is the official English langua

7、ge version of EN 14954:2005.The UK participation in its preparation was entrusted to Technical Committee PRI/57, Surfaces for sports areas, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any EUROPEAN STANDARDNORME EU

8、ROPENNEEUROPISCHE NORMEN 14954November 2005ICS 97.220.10English VersionSurfaces for sports areas - Determination of hardness of naturalturf and unbound mineral surfaces for outdoor sports areasSols sportifs - Dtermination de la duret du gazon naturelet des sols minraux non lis pour les terrains de s

9、port deplein airSportbden - Bestimmung der Hrte von Naturrasen undungebundenen mineralischen Belgen fr Sportbden frden AuenbereichThis European Standard was approved by CEN on 12 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions f

10、or giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official v

11、ersions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium,

12、Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROP

13、EN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14954:2005: EEN 14954:2005 (E) 2 Contents Page Foreword 3 1 Scope .4 2 Princ

14、iple.4 3 Apparatus 4 4 Procedure 4 5 Number and distribution of readings 5 6 Expression of results5 7 Test report .5 Bibliography.7 EN 14954:2005 (E) 3 Foreword This European Standard (EN 14954:2005) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of

15、which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by May 2006. According to the CEN/CENELEC Intern

16、al Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl

17、ands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14954:2005 (E) 4 1 Scope This European Standard specifies a method for the determination of hardness of natural turf and unbound mineral surfaces. 2 Principle A cylindrical weight is released from a

18、 standard height onto the surface and its peak deceleration during impact is recorded. 3 Apparatus 3.1 Test weight, comprising a solid metal, plane-ended cylinder containing an accelerometer (3.2) securely fastened within a protective housing. The accelerometer shall be attached to a BNC connector (

19、see Figure 1). The total mass of the assembly shall be (2,5 0,005) kg for testing natural turf and (4,5 0,005) kg for testing unbound mineral surfaces. 3.2 Accelerometer, the signal from which shall be conditioned by an amplifier and a filter. The gain of the amplifier shall be adjusted to match the

20、 output of the associated accelerometer so that the instrument displays hardness value directly. The filter shall be a two-pole low-pass Bessel filter with a 500 Hz cut-off frequency. NOTE This type of filter is used because it has minimal overshoot with a step input signal. The filter output shall

21、be digitized by a micro-controller. The micro-controller shall sample the accelerometer output at a frequency of 20 kHz. The micro-controller shall determine the peak acceleration from the digitised waveform and use it to calculate the hardness value. The hardness value and drop number shall be disp

22、layed on the hand-held read-out. The drop number indicator shall increase with each measurement. 3.3 Coaxial cable, to connect the test weight to a recording meter (3.4). 3.4 Recording meter, capable of reading and displaying the peak deceleration of the test weight during impact with the test surfa

23、ce, filtered to limit the frequency to below 7 kHz and showing the deceleration in gravities (g). NOTE Some meters show deceleration as impact values, where one impact value is equal to ten gravities. In such cases the displayed values will have to be multiplied by ten to convert to gravities. 3.5 G

24、uide tube, to control the height of drop of the test weight while not restricting its free fall. The guide tube shall have a diameter of (54 1) mm and a length of at least 600 mm. An air vent having a diameter of (10 1) mm shall be positioned (40 10) mm from the base of the tube. The guide tube typi

25、cally has a circular flange at the base of approximately 150 mm diameter to allow the tube to stand vertically. NOTE The apparatus described is similar in principle to that described by Clegg 1. 4 Procedure Position the guide tube vertically on the surface to be tested and drop the impact weight dow

26、n the tube. One of the following two release heights shall be used: a) for soccer, rugby and hockey pitches, the release height shall be (550 10) mm; b) for golf, cricket and lawn bowls, the release height shall be (300 10) mm. EN 14954:2005 (E) 5 After the impact of the weight on the surface, recor

27、d the peak deceleration in units of gravities (taking the acceleration due to the gravity into account). Carry out the test five times consecutively on the same spot. After each series of five readings move the guide apparatus so that the weight does not impact with the surface on the same spot twic

28、e. Record the value of the fifth drop if it does not deviate more than two impact values from the previous one (20 g). If the value lies outside this range, consider the results as invalid and repeat the test. 5 Number and distribution of readings Unless otherwise specified, take at least eight read

29、ings at random on areas less than 100 m2, take 8 to15 readings, as appropriate, on areas of 100 m2to 1 000 m2 and 15 to20 readings for areas of 1 000 m2to 5 000 m2. Subdivide larger areas into two or more areas for testing. 6 Expression of results For the 2,5 kg impact weight, hardness value is equa

30、l to the peak of g. For the 4,5 kg impact weight, hardness value is equal to the peak of g/10. Calculate the mean hardness value for each area. 7 Test report The test report shall include the following information: a) reference to this European Standard i.e. EN 14954:2005; b) complete identification

31、 of the surface tested, including its location, area and previous history; c) mean value of impact value and hardness; d) individual test results, if required; e) details of any deviation from the procedure. EN 14954:2005 (E) 6 Dimensions in millimetres Key 1 To meter 2 BNC connector 3 Accelerometer

32、 Figure 1 Test weight EN 14954:2005 (E) 7 Bibliography 1 Clegg B (1976) An impact testing device for in situ base course evaluation. Australian Road Res. Bureau Proc. 8, 1-6 BS EN BSI389 Chiswick High RoadLondonW4 4AL14954:2005BSI British Standards InstitutionBSI is the independent national body res

33、ponsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amend

34、ments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be fou

35、nd on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards

36、 publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of t

37、hose that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information servic

38、es are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase

39、price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information ab

40、out BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract ma

41、y be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, a

42、nd size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.