BS EN 14810-2006 Surfaces for sports areas - Determination of spike resistance《运动场表面 鞋钉阻力的测定》.pdf

《BS EN 14810-2006 Surfaces for sports areas - Determination of spike resistance《运动场表面 鞋钉阻力的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14810-2006 Surfaces for sports areas - Determination of spike resistance《运动场表面 鞋钉阻力的测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58The European Standard EN 14810:2006 has the status of a British StandardICS 97.220.10Surfaces for s

2、ports areas Determination of spike resistanceBRITISH STANDARDBS EN 14810:2006BS EN 14810:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006ISBN 0 580 48777 6A list of organizations represented on this committee can be o

3、btained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility

4、 of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Sum

5、mary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date Comments

6、aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis

7、British Standard is the official English language version of EN 14810:2006. It partially supersedes BS 7044-2.3:1990 (replacing method 5). EN 14810:2006 is one of a package of standards being produced by CEN/TC 217. On publication of the entire package, BS 7044 will be withdrawn.The UK participation

8、 in its preparation was entrusted to Technical Committee PRI/57, Surfaces for sports areas, which has the responsibility to: EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14810April 2006ICS 97.220.10English VersionSurfaces for sports areas - Determination of spike resistanceSols sportifs - Dterm

9、ination de la rsistance aux pointes Sportbden - Bestimmung der Bestndigkeit gegen SpikesThis European Standard was approved by CEN on 20 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status

10、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A versio

11、n in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, F

12、inland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOM

13、ITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14810:2006: EEN 14810:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Principle4 4 App

14、aratus .4 5 Test specimen5 6 Conditioning.5 7 Procedure .5 8 Expression of results 6 9 Test report 6 EN 14810:2006 (E) 3 Foreword This document (EN 14810:2006) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by BSI. This European Stan

15、dard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at the latest by October 2006. According to the CEN/CENELEC Internal Regulations, the national sta

16、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

17、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14810:2006 (E) 4 1 Scope This European Standard specifies a method for the determination of the resistance of a synthetic sports surface to spikes. 2 Normative references The following referenced documents are indispensab

18、le for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12230, Surfaces for sports areas Determination of tensile properties of synthetic sport

19、s surfaces 3 Principle A test specimen of the sports surface is exposed to a wearing process by a metal roller fitted with spikes. The differences in tensile strength and elongation at break of the synthetic sports surface, measured before and after the wearing process, are a measure of the resistan

20、ce of the surface to spikes. 4 Apparatus 4.1 Spike apparatus, comprising a platform fitted with a rotating vertical shaft powered by an electric motor with adjustable speed. 4.2 Roller with spikes (see Figure 1), consisting of a horizontal spindle fitted with 12 wheels having a thickness of (10 1) m

21、m and a diameter of (36 1) mm. 10 of the wheels shall be fitted with six spikes each, the spikes having a length of (9 1) mm and a diameter at the base of (5 1) mm. Each of the 12 wheels shall be completely free to rotate, both on the spindle and relative to its neighbours. The roller shall be centr

22、ally mounted on the vertical shaft of the spike apparatus, in such a way that it rotates with the shaft but is able to move freely in the vertical direction. The total mass of the roller shall be adjusted to (10 0,1) kg. EN 14810:2006 (E) 5 Dimensions in millimetres Figure 1 Metal roller fitted with

23、 spikes 5 Test specimen Prepare four test specimens of the synthetic sports surface each having dimensions of 180 mm 220 mm. One specimen shall be used for the initial determination of tensile properties. Two specimens shall be subjected to the wear process and shall then be used for determining the

24、 tensile properties after wear. The fourth specimen shall be set aside as a reference. 6 Conditioning The test shall be carried out under laboratory conditions at a temperature of (23 2) C and a relative humidity of (50 10) %. 7 Procedure Carry out tensile tests according to EN 12230 on five tensile

25、 test pieces cut from one test specimen. Adjust the speed of the electric motor to (20 2) rev/min. Fasten the second test specimen in the holder on the platform of the spike apparatus. Switch on the motor and let it run for (1 200 20) rev. Remove the test specimen from the platform. Repeat this proc

26、edure on a third test specimen. Carry out tensile tests according to EN 12230 on five tensile test pieces from the areas of a diameter of (140 10) mm of the second and third test specimens affected by the spikes. EN 14810:2006 (E) 6 Visually examine the worn third specimen with the naked eye. Bend t

27、he third test specimen affected by the spikes over a mandrel with a diameter of (70 5) mm. Describe obvious changes, such as cracks, clear removal of material particles from the surface, wear of the surface, in the specimen in comparison to the specimen not affected by spikes. Denote such changes as

28、 visual damage. 8 Expression of results The resistance to spikes shall be expressed in terms of the changes in tensile strength T and elongation at break E resulting from the effects of spikes. Calculate the average tensile strength and elongation at break before wear T1and E1and after wear T2and E2

29、. Calculate the change of tensile strength, X, using the formula: 121100TTXT=(1) where X is the change in tensile strength, expressed as a percentage (%); T1is the initial tensile strength, expressed in kilopascal (kPa); T2is the tensile strength after wear, expressed in kilopascal (kPa). Calculate

30、the change of elongation at break, Y, using the formula: 121100EEYE=(2) where: Y is the change in elongation at break expressed as a percentage (%); E1is the initial elongation at break, expressed in millimetres (mm); E2is the elongation at break after wear, expressed in millimetres (mm). 9 Test rep

31、ort The test report shall include the following information: a) reference to this European Standard, i.e. EN 14810:2006; b) description of the nature of the test surface; c) description of visual damage, as described in Clause 7; d) test results X and Y expressed in accordance with Clause 8; e) deta

32、ils of any deviation from this procedure and additional relevant observations. blankBS EN BSI389 Chiswick High RoadLondonW4 4AL14810:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe a

33、nd at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and

34、 services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offer

35、s members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44

36、 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information

37、 on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf

38、ormation Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administrat

39、ion. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in a

40、ll BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means e

41、lectronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.