BS EN 14783-2013 Fully supported metal sheet and strip for roofing external cladding and internal lining Product specification and requirements《盖屋顶、外部覆层和内衬用全支撑金属薄板材和带材 产品规格和要求》.pdf

《BS EN 14783-2013 Fully supported metal sheet and strip for roofing external cladding and internal lining Product specification and requirements《盖屋顶、外部覆层和内衬用全支撑金属薄板材和带材 产品规格和要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14783-2013 Fully supported metal sheet and strip for roofing external cladding and internal lining Product specification and requirements《盖屋顶、外部覆层和内衬用全支撑金属薄板材和带材 产品规格和要求》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 14783:2013Fully supported metal sheetand strip for roofing, externalcladding and internal lining Product specification andrequirementsBS EN 14783:2013 BRITISH STANDARDNatio

2、nal forewordThis British Standard is the UK implementation of EN 14783:2013. Itsupersedes BS EN 14783:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/542/6, Corrugated sheeting materials.A list of organizations represented on this committee can b

3、eobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 79139 0ICS 77.140.50; 77.150.01

4、; 91.060.10; 91.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2013.Amendments issued since publicationDate Text affectedBS EN 14783:2013EUROPEAN STA

5、NDARD NORME EUROPENNE EUROPISCHE NORM EN 14783 May 2013 ICS 77.140.50; 77.150.01; 91.060.10; 91.060.20 Supersedes EN 14783:2006English Version Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements Tles et bandes mtalliques t

6、otalement supportes pour couverture, bardages extrieur et intrieur - Spcification de produit et exigences Vollflchig untersttzte Dachdeckungs- und Wandbekleidungselemente fr die Innen- und Auenanwendung aus Metallblech - Produktspezifikation und Anforderungen This European Standard was approved by C

7、EN on 24 February 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standa

8、rds may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and not

9、ified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, I

10、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Cen

11、tre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14783:2013: EBS EN 14783:2013EN 14783:2013 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 R

12、equirements .6 4.1 Materials .6 4.2 Nominal thickness .6 4.3 Water permeability .7 4.4 Dimensional change 7 4.5 Dimensional tolerances 7 4.6 Vapour and air permeability .7 4.7 Release of dangerous substances .7 4.8 Durability 7 4.9 External fire performance .8 4.10 Reaction to fire .8 5 Testing, ass

13、essment and sampling methods .8 5.1 External fire performance for roof covering products .8 5.1.1 Products deemed to satisfy the requirements for external fire performance .8 5.1.2 Products classified without the need for further testing .8 5.1.3 Other products .8 5.2 Reaction to fire .9 5.2.1 Produ

14、cts satisfying the requirements for reaction to fire Class A1 without the need for testing .9 5.2.2 Other products .9 5.3 Release of dangerous substances .9 6 Evaluation of conformity .9 6.1 General 9 6.2 Initial type testing (ITT) .9 6.2.1 General 9 6.2.2 Sampling for ITT 12 6.3 Factory production

15、control (FPC) . 12 6.3.1 General . 12 6.3.2 General requirements . 13 7 Designation . 14 8 Product marking . 14 Annex A (normative) Multilayer coated steel sheet 15 A.1 General . 15 A.2 Substrate material. 15 A.3 Specific requirements 15 A.3.1 Minimum nominal values of thickness . 15 A.3.2 Bituminou

16、s coating specification . 15 A.3.3 Durability . 16 A.4 Freedom from defects 16 Annex B (normative) Test conditions for the reaction to fire tests 17 B.1 General . 17 B.2 Mounting and fixing conditions of test specimens in the SBI test 17 B.2.1 General . 17 BS EN 14783:2013EN 14783:2013 (E) 3 B.2.2 G

17、eneral configuration . 17 B.2.3 Securing the overlap vertical joint . 19 B.2.4 Standard assembly-steel corner flashings . 19 B.2.5 Alternative assembly-corner flashings and seals 19 B.3 Test arrangement for reaction to fire test according to EN ISO 11925-2 . 19 Annex ZA (informative) Clauses of this

18、 European Standard addressing the provisions of EU Construction Products Directive . 20 ZA.1 Scope and relevant characteristics . 20 ZA.2 Procedure(s) for the attestation of conformity of products 21 ZA.2.1 Systems of attestation of conformity 21 ZA.2.2 EC Certificate and Declaration of conformity .

19、 24 ZA.3 CE marking and labelling 25 Bibliography 28 BS EN 14783:2013EN 14783:2013 (E) 4 Foreword This document (EN 14783:2013) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NB

20、N. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2013, and conflicting national standards shall be withdrawn at the latest by November 2013. Attention is drawn to the possibility that s

21、ome of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, a

22、nd supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document supersedes EN 14783:2006. In comparison to the previous edition, the following sections have been modified: Clause 3, subc

23、lause 5.3 and Annex ZA. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic o

24、f Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14783:2013EN 14783:2013 (E) 5 1 Scope This European Stand

25、ard specifies the terminology, requirements and test methods for metal coil, strip, and flat sheets and factory made pieces intended for fully supported applications in roofing and wall cladding or lining. It does not apply to products manufactured on site. This European Standard covers fully-suppor

26、ted aluminium, copper, lead, steel, stainless steel and zinc products with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A). This European Standard also includes rules for marking, labelling and evaluation of conformity. Requirements concerning acoustical and insul

27、ation properties are not considered in this European Standard. This European Standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products. 2 Normative references The following documents, in whole or in pa

28、rt, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. CEN/TS 1187, Test methods for external fire expos

29、ure to roofs EN 501:1994, Roofing products from metal sheet Specification for fully supported roofing products of zinc sheet EN 502:2013, Roofing products from metal sheet Specification for fully supported roofing products of stainless steel sheet EN 504:1999, Roofing products from metal sheet Speci

30、fication for fully supported roofing products of copper sheet EN 505:2013, Roofing products from metal sheet Specification for fully supported roofing products of steel sheet EN 507:1999, Roofing products from metal sheet Specification for fully supported roofing products of aluminium sheet EN 1427,

31、 Bitumen and bituminous binders Determination of the softening point Ring and Ball method EN 10088-1, Stainless steels Part 1: List of stainless steels EN 12588:2006, Lead and lead alloys Rolled lead sheet for building purposes EN 13501-1, Fire classification of construction products and building el

32、ements Part 1: Classification using data from reaction to fire tests EN 13501-5, Fire classification of construction products and building elements Part 5: Classification using data from external fire exposure to roofs tests EN 13823, Reaction to fire tests for building products Building products ex

33、cluding floorings exposed to the thermal attack by a single burning item EN ISO 6270-1, Paints and varnishes Determination of resistance to humidity Part 1: Continuous condensation (ISO 6270-1) BS EN 14783:2013EN 14783:2013 (E) 6 EN ISO 6988, Metallic and other non-organic coatings Sulphur dioxide t

34、est with general condensation of moisture (ISO 6988) EN ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests (ISO 9227) EN ISO 11925-2, Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test (ISO 11925-2) 3 Terms and

35、definitions For the purposes of this document, the terms and definitions given in EN 501:1994, EN 502:2013, EN 504:1999, EN 505:2013, EN 507:1999, EN 12588:2006 and the following apply. 3.1 base material coated or non-coated coil, strip or flat sheet of metal used for the production of a roofing, cl

36、adding or lining product according to this European Standard 4 Requirements 4.1 Materials The materials for the fully supported metal products specified in this European Standard shall be in accordance with the relevant material standards listed in EN 501, EN 502, EN 504, EN 505, EN 507 and EN 12588

37、. For multilayer coated steel sheet, the requirements as given in Annex A shall apply. 4.2 Nominal thickness The nominal thickness of the fully supported metal products (excluding any organic, inorganic or multilayer coating) shall be equal to or greater than the values given in Table 1 as specified

38、 in EN 501, EN 502, EN 504, EN 505, EN 507 and EN 12588. Table 1 Minimum nominal values of thickness Type of metal Reference of the European Standard Specified minimum nominal thickness in mmaAluminium EN 507 0,6 Copper EN 504 0,5 Lead EN 12588 1,25 Stainless steel EN 502 0,4 Steel EN 505 0,5 Zinc E

39、N 501 0,6 aMember States of use may require greater thickness than the value shown. BS EN 14783:2013EN 14783:2013 (E) 7 4.3 Water permeability As long as the products covered by this European Standard have no holes (as defects), they are water impermeable. Where required, the absence of holes shall

40、be checked by visual inspection of the finished product. 4.4 Dimensional change The thermal expansion shall be taken into account in the change of dimensions of the product, where this change may have an effect on the performance of the product, by stating the appropriate thermal expansion coefficie

41、nt. In the absence of experimental data, the following thermal expansion coefficient shall be used: aluminium: 24 x 106K1, copper: 16,8 x 106K1, lead: 29,3 x 106K1, stainless steel: 10,0 x 106K1to 17,0 x 106K1, depending on the grade, according to EN 10088-1, steel: 12 x 106K1, zinc: 22 x 106K1, unl

42、ess the manufacturer demonstrates by appropriate means that more accurate values are applicable. 4.5 Dimensional tolerances The dimensional tolerances specified for roof covering products in the applicable standard from the following: EN 501, EN 502, EN 504, EN 505, EN 507 and EN 12588, shall not be

43、 exceeded. For other products, the tolerances declared shall be appropriate, due account being taken of any national provisions of the country of use. 4.6 Vapour and air permeability As long as the products covered by this European Standard have no holes (as defects), they are air and vapour imperme

44、able. Where required, the absence of holes shall be checked by visual inspection of the finished product. 4.7 Release of dangerous substances Where the manufacturer wishes to make a declaration (e.g. when subject to regulatory requirements), the release of dangerous substances of the products specif

45、ied in this European Standard shall be declared according to the provisions of 5.3. 4.8 Durability The manufacturer shall state the type, thickness and grade of metal and, if appropriate, type and thickness (or mass) and/or category of any coating(s) to enable users to select products which may be e

46、xpected to provide the required durability of the product having regard to the expected environment and/or exposure conditions and feasibility of maintenance. BS EN 14783:2013EN 14783:2013 (E) 8 Where this is not appropriate, the durability of the product shall be determined in accordance with the t

47、echnical specifications valid in the country of use. 4.9 External fire performance The manufacturer shall declare the external fire performance of the products specified in this European Standard when subject to regulatory requirements, and may declare the external fire performance of the products w

48、hen not subject to such requirements, according to the provisions of 5.1 or declared as Class FROOF. 4.10 Reaction to fire The manufacturer shall declare the reaction to fire performance of the products specified in this European Standard when subject to regulatory requirements, and may declare the

49、external fire performance of the products when not subject to such requirements, according to the provisions of 5.2 or declared as Class F. 5 Testing, assessment and sampling methods 5.1 External fire performance for roof covering products 5.1.1 Products deemed to satisfy the requirements for external fire performance Products covered by this European Standard are considered ”deemed to satisfy without the need for testing“ in relation to the requirements for external fire performance provided that they meet