BS EN 14392-2007 Aluminium and aluminium alloys - Requirements for anodised products for use in contact with foodstuff《铝和铝合金 与食品接触的阳极产品的要求》.pdf

《BS EN 14392-2007 Aluminium and aluminium alloys - Requirements for anodised products for use in contact with foodstuff《铝和铝合金 与食品接触的阳极产品的要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14392-2007 Aluminium and aluminium alloys - Requirements for anodised products for use in contact with foodstuff《铝和铝合金 与食品接触的阳极产品的要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58a

2、nodised products for use in contact with foodstuffICS 67.250; 77.150.19Aluminium and aluminium alloys Requirements for BRITISH STANDARDBS EN 14392:2007BS EN 14392:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIThis British Standard was publishe

3、d under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 53127 9Amendments/corrigenda issued since publicationDate CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is

4、 the UK implementation of EN 14392:2007.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include al

5、l the necessary provisions of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14392November 2007ICS 77.150.10; 67.250English VersionAluminium and aluminium alloys - Requirements for anodisedproducts for use in contact with foodstuffAlum

6、inium et alliages daluminium - Spcifications pour lesproduits anodiss destins entrer en contact avec lesalimentsAluminium und Aluminiumlegierungen - Anforderungen ananodisierte Erzeugnisse, die in Kontakt mit LebensmittelnkommenThis European Standard was approved by CEN on 15 June 2007.CEN members a

7、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to t

8、he CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same s

9、tatus as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania,

10、 Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwi

11、de for CEN national Members.Ref. No. EN 14392:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIEN 14392:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Ordering information.5 5 Chemical compos

12、ition of the aluminium or aluminium alloy .5 6 Chemical composition of the anodization bath5 7 Sealing 5 7.1 General5 7.2 Composition of the sealing bath5 7.3 Technical parameters of the sealing process.6 7.4 Quality assurance and quality assessment 6 8 Demonstration of conformity with the present s

13、tandard 7 Annex A (informative) Adeviations8 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIEN 14392:2007 (E) 3 Foreword This document (EN 14392:2007) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secreta

14、riat of which is held by AFNOR. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008 and conflicting national standards shall be withdrawn at the latest by May 2008. Within its programme of work, Techn

15、ical Committee CEN/TC 132 has entrusted CEN/TC 132/WG 9 to prepare the following standard: EN 14392, Aluminium and aluminium alloys Requirements for anodised products for use in contact with foodstuff. Attention is drawn to the possibility that some of the elements of this document may be the subjec

16、t of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product

17、shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, G

18、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) B

19、SIEN 14392:2007 (E) 4 1 Scope This European Standard specifies requirements for coloured or uncoloured anodic oxidation coatings on wrought and cast products in aluminium and aluminium alloys for use in contact with food. These requirements cover the chemical composition of the bath, the sealing and

20、 the properties of the obtained anodic oxidation coatings. They do not cover dyestuffs and pigments but do cover the metallic deposits produced by electrolytic colouring. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer

21、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 601, Aluminium and aluminium alloys Castings Chemical composition of castings for use in contact with foodstuff EN 602, Aluminium and aluminium alloys W

22、rought products Chemical composition of semi products used for the fabrication of articles for use in contact with foodstuff EN 10204, Metallic products Types of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 12373-1, Aluminium and

23、 aluminium alloys Anodizing Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium EN 12373-4, Aluminium and aluminium alloys Anodizing Part 4: Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid t

24、reatment EN 12373-5, Aluminium and aluminium alloys Anodizing Part 5: Assessment of quality of sealed anodic oxidation coatings by measurement of admittance EN 12373-7, Aluminium and aluminium alloys Anodizing Part 7: Assessment of quality of sealed anodic oxidation coatings by measurement of the lo

25、ss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 anodic oxidation coating coating obtained by an electrolytic oxidat

26、ion process, having protective, decorative or functional properties 3.2 sealing treatment of anodic oxide coating to reduce porosity and the absorption capacity of the coating by hydrothermal processes carried out after anodising Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:1

27、8, Uncontrolled Copy, (c) BSIEN 14392:2007 (E) 5 3.3 order document document or set of documents agreed between supplier and purchaser at the time of ordering NOTE An order document can be an order of the purchaser confirmed by the supplier or a quotation of the supplier confirmed by the purchaser.

28、4 Ordering information In addition to the information necessary for sufficient definition of the product and its properties as defined by EN 12373-1, order documents shall contain the following information: a) the number of this European Standard; b) any requirement on the periodicity of inspection

29、certificates (see Clause 8). 5 Chemical composition of the aluminium or aluminium alloy The chemical composition of the aluminium or aluminium alloys for use in contact with food, intended to be anodised, shall comply with the requirements of EN 601 or EN 602, as applicable. 6 Chemical composition o

30、f the anodization bath The anodization of aluminium or aluminium alloy products intended to be in contact with foodstuff shall be carried out in a diluted aqueous solution of one or more of the following acids: sulfuric acid; sulfomaleic acid; sulfosalicylic acid; oxalic acid; sulfophtalic acid; pho

31、sphoric acid. 7 Sealing 7.1 General The anodic oxidation coating shall be sealed unless the coating has been produced in a bath containing only diluted phosphoric acid, or unless the product on which the anodic oxidation coating has been produced will receive another organic or inorganic coating pri

32、or to use in contact with food. 7.2 Composition of the sealing bath Sealing shall be done in distilled or demineralized water, which may contain appropriate additives. The inspection certificate shall confirm that the additives and their respective concentrations in the sealing bath comply with curr

33、ent legal requirements. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIEN 14392:2007 (E) 6 7.3 Technical parameters of the sealing process All the technical parameters of the sealing process, especially the temperature and pH of the bath, the durat

34、ion of the treatment and the nature and concentration of additives shall be chosen to minimise the absorptive power of the anodic oxidation coating and maximise its chemical resistance and to minimizer the migration of potentially hazardous additives. 7.4 Quality assurance and quality assessment The

35、 producer shall set up a suitable quality assurance system in order to monitor the quality of the sealing. The method described in EN 12373-4 and EN 12373-5 shall be used for routine control, and the method described in EN 12373-7 for calibration purpose. NOTE Quality assurance and quality assessmen

36、t can be done in the framework of a recognised European quality label such as QUALANOD1). 1)QUALANOD c/o AC Treuhand AG P.O. Box 1507 Tdistrasse 47 CH 8002 Zrich Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIEN 14392:2007 (E) 7 8 Demonstration of

37、conformity with the present standard The anodizing of aluminium and aluminium alloys products for use in contact with food shall be carried out in the framework of a quality assurance system. This quality assurance system shall allow traceability of a delivered lot to the parameters of the productio

38、n process that are relevant to the present standard (see Clauses 5 to 7). The manufacturer shall establish an inspection certificate “3.1“ according to EN 10204 which certifies compliance of the delivered products with the requirements of the present standard. Unless otherwise agreed upon between ma

39、nufacturer and purchaser, this certificate can be issued at the discretion of the manufacturer either for each delivered lot, or periodically for all products delivered under the present standard within a period of time not exceeding twelve months. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDAR

40、DS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIEN 14392:2007 (E) 8 Annex A (informative) Adeviations A- deviation: National deviation due to regulations, the alteration of which is for the time being outside the competence of the CEN/CENELEC member. This European Standard does not fall under any Di

41、rective of the EU. In the relevant CEN/ CENELEC countries these A-deviations are valid instead of the provisions of the European Standard until they have been removed. Deviation 7.1 (France) The Order of 27th August 1987 concerning aluminium or aluminium alloys materials and objects in contact with

42、foodstuffs, products and food drinks, article 5, enumerates authorized acids put in contact with the above products intended for the French territory. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIblankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA S

43、TANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSIBS EN BSILicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/05/2008 08:18, Uncontrolled Copy, (c) BSI389 Chiswick High RoadLondonW4 4AL14392:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparin

44、g British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It

45、is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fron

46、t cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should

47、be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been p

48、ublished as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available

49、 which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to