BS EN 14227-4-2013 Hydraulically bound mixtures Specifications Fly ash for hydraulically bound mixtures《液力粘结混合料 规格 液力粘结混合料用飞灰》.pdf

《BS EN 14227-4-2013 Hydraulically bound mixtures Specifications Fly ash for hydraulically bound mixtures《液力粘结混合料 规格 液力粘结混合料用飞灰》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14227-4-2013 Hydraulically bound mixtures Specifications Fly ash for hydraulically bound mixtures《液力粘结混合料 规格 液力粘结混合料用飞灰》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 14227-4:2013Hydraulically bound mixtures SpecificationsPart 4: Fly ash for hydraulically boundmixturesBS EN 14227-4:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14227-4:2013.It supersedes BS EN 14227-4:2004 which is withdra

2、wn.The UK participation in its preparation was entrusted to TechnicalCommittee B/510/4, Cementitious bound materials, unboundgranular materials, waste materials and marginal materials.A list of organizations represented on this committee can beobtained on request to its secretary.This publication do

3、es not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 74215 6ICS 93.080.20Compliance with a British Standard cannot confer immunity fromlegal

4、obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14227-4 May 2013 ICS 93.080.20 Supersedes EN 14227-4:2004English

5、 Version Hydraulically bound mixtures - Specifications - Part 4: Fly ash for hydraulically bound mixtures Mlanges traits aux liants hydrauliques - Spcifications - Partie 4: Cendre volante pour mlanges traits aux liants hydrauliques Hydraulisch gebundene Gemische - Anforderungen - Teil 4: Flugasche f

6、r hydraulisch gebundene Gemische This European Standard was approved by CEN on 1 March 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date

7、 lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation u

8、nder the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Forme

9、r Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT E

10、UROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14227-4:2013: EBS EN 14227-4:2013EN 14227-4:2013 (E) 2 Contents Page F

11、oreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Requirements .5 4.1 General 5 4.2 Requirements for siliceous fly ash 5 4.2.1 Particle size 5 4.2.2 Loss on ignition .5 4.2.3 Sulfuric anhydride .5 4.2.4 Free calcium oxide and soundness .6 4.2.5 Water content .6 4.2.6 Pozzolan

12、ic activity of siliceous fly ash .6 4.3 Requirements for calcareous fly ash .6 4.3.1 Particle size 6 4.3.2 Soundness 6 4.3.3 Reactive calcium oxide .6 4.3.4 Water content .6 4.3.5 Hydraulic activity of calcareous fly ash 6 5 Production control .7 6 Marking and labelling 7 BS EN 14227-4:2013EN 14227-

13、4:2013 (E) 3 Foreword This document (EN 14227-4:2013) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,

14、at the latest by November 2013, and conflicting national standards shall be withdrawn at the latest by November 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying

15、 any or all such patent rights. This document supersedes EN 14227-4:2004. Compared with EN 14227-4:2004, the following changes have been made: Revision of Clause 4.2 “Requirements for siliceous fly ash“; Revision of Clause 4.3 “Requirements for calcareous fly ash“. This standard is one of a series o

16、f parts for EN 14227, Hydraulically bound mixtures Specifications: Part 1: Cement bound granular mixtures Part 2: Slag bound granular mixtures Part 3: Fly ash bound granular mixtures Part 4: Fly ash for hydraulically bound mixtures Part 5: Hydraulic road binder bound granular mixtures Part 10: Soil

17、treated by cement Part 11: Soil treated by lime Part 12: Soil treated by slag Part 13: Soil treated by hydraulic road binder Part 14: Soil treated by fly ash According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this

18、 European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia

19、, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14227-4:2013EN 14227-4:2013 (E) 4 1 Scope This European Standard specifies siliceous and calcareous fly ash used in hydraulically bound mixtures for roads, airfields and other trafficked areas. This European Standard applie

20、s to fly ash produced by the combustion of pulverised coal or lignite in energy generating plants. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

21、applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement Part 1: Determination of strength EN 196-2, Methods of testing cement Part 2: Chemical analysis of cement EN 196-3, Methods of testing cement Part 3:

22、 Determination of setting times and soundness EN 196-7, Methods of testing cement Part 7: Methods of taking and preparing samples of cement EN 197-1, Cement Part 1: Composition, specifications and conformity criteria for common cements EN 450-1, Fly ash for concrete Part 1: Definition, specification

23、s and conformity criteria EN 451-1, Method of testing fly ash Part 1: Determination of free calcium oxide content EN 451-2, Method of testing fly ash Part 2: Determination of fineness by wet sieving EN 933-10, Tests for geometrical properties of aggregates Part 10: Assessment of fines Grading of fil

24、ler aggregates (air jet sieving) EN 13286-1, Unbound and hydraulically bound mixtures Part 1: Test methods for laboratory reference density and water content Introduction, general requirements and sampling 3 Terms and definitions For the purposes of this document, the following terms and definitions

25、 apply. 3.1 fly ash fine powder produced by the combustion of pulverised coal or lignite with or without co-combustion materials (as defined in EN 450-1) in energy generating plants and captured by mechanical or electrostatic precipitators 3.2 siliceous fly ash (alumino-silicate fly ash) fly ash whe

26、re the essential chemical components are silicates, aluminates and iron oxides, expressed as SiO2, Al2O3and Fe2O3and which has pozzolanic properties Note 1 to entry: It may be stored, supplied and used either in a wet or dry condition. BS EN 14227-4:2013EN 14227-4:2013 (E) 5 3.3 calcareous fly ash (

27、sulfo-calcitic fly ash) fly ash where the essential chemical components are silicates, aluminates, calcium oxide and sulfates, expressed as SiO2, Al2O3, CaO and SO3and which has hydraulic and pozzolanic properties Note 1 to entry: It is stored and supplied in a dry condition. 3.4 pozzolanic material

28、 material which mixed with lime Ca(OH)2or CaO in the presence of water sets and hardens to form stable and durable compounds 3.5 hydraulic material material which sets and hardens in the presence of water, to form stable and durable compounds 3.6 dry fly ash fly ash with a very low water content, se

29、e 4.2.5 and 4.3.4 Note 1 to entry: Normally supplied directly from dry storage. 4 Requirements 4.1 General Chemical characteristics shall be expressed as a percentage by mass of the dry product which is obtained by drying a laboratory sample in a well-ventilated oven at (110 5) C to constant mass, a

30、nd allowing to cool in a dry atmosphere. For dry fly ash, samples shall be taken and prepared in accordance with EN 196-7. For wet fly ash, samples shall be taken and prepared in accordance with EN 13286-1. 4.2 Requirements for siliceous fly ash 4.2.1 Particle size The fineness of fly ash shall be e

31、xpressed as the mass proportion in percent of the ash retained when sieved on a 0,045 mm mesh sieve and shall not exceed 60 %. The sieving shall be carried out in accordance with EN 451-2 (wet sieving) or by air-jet sieving in accordance with EN 933-10. 4.2.2 Loss on ignition The loss on ignition me

32、asured in accordance with EN 196-2, but using an ignition time of 1 h, or equivalent method, shall not exceed 15,0 % by mass. 4.2.3 Sulfuric anhydride The content of sulfuric anhydride, SO3shall be determined in accordance with EN 196-2 and shall not be greater than 4,0 % by mass. BS EN 14227-4:2013

33、EN 14227-4:2013 (E) 6 4.2.4 Free calcium oxide and soundness If the free calcium oxide content, measured in accordance with EN 451-1, exceeds 1,5 % by mass, soundness shall be measured according to EN 196-3 and the expansion shall not exceed 10 mm with a 30:70 blend of fly ash and cement. 4.2.5 Wate

34、r content Dry siliceous fly ash shall contain not more than 1,0 % by mass of water. NOTE Siliceous fly ash can be stored, used and supplied either in a wet or a dry condition. 4.2.6 Pozzolanic activity of siliceous fly ash If required at the place of use, the pozzolanic activity shall be declared. T

35、his may be determined by the measurement of the compressive strength of a mixture of lime, the ash in question and standard aggregate. 4.3 Requirements for calcareous fly ash 4.3.1 Particle size The fineness of fly ash shall be expressed as the mass proportion in percent of the ash retained when sie

36、ved on a 0,090 mm mesh sieve and shall not exceed 30 %. The sieving shall be carried out in accordance with EN 451-2 (wet sieving) or by air-jet sieving in accordance with EN 933-10. 4.3.2 Soundness The expansion of calcareous fly ash shall be less than 10 mm, when tested in accordance with EN 196-3

37、, using a mixture of 30 % by mass of ground fly ash and 70 % by mass of reference cement. 4.3.3 Reactive calcium oxide The total value of reactive CaO determined in accordance with EN 197-1 shall not be less than 5 % by mass. 4.3.4 Water content Dry calcareous fly ash shall contain not more than 1 %

38、 by mass of water. Calcareous fly ash shall be stored and supplied in a dry condition. 4.3.5 Hydraulic activity of calcareous fly ash If required at the place of use, the hydraulic activity shall be declared. This may be determined by the measurement of compressive strength development over time of

39、mixtures of fly ash and a standard aggregate. The test procedure shall be in accordance with EN 196-1 except that the specimens should be stored in the mould at least 7 days.1)1) BAST: Suitability of mixtures for hydraulically bound base courses according to European Standards for applications in Ge

40、rmany, Research Project No. FE 08.0181/2004/NGB, Bundesanstalt fr Straenbau (BAST), 2008. BS EN 14227-4:2013EN 14227-4:2013 (E) 7 5 Production control Fly ash shall be controlled according to Table 1. The manufacturer shall establish and maintain a production control manual, setting out the procedur

41、es by which the requirements for production control are satisfied. Table 1 Production control Column 1 2 3 4 Line Property Minimum test frequencyaClause reference Siliceous fly ash Calcareous fly ash 1 Particle size 2 per month or 1 per 5 000 t 4.2.1 4.3.1 2 Loss on ignition 2 per month or 1 per 5 0

42、00 t 4.2.2 Not applicable 3 Sulphuric anhydride 1 per month or 1 per 10 000 t 4.2.3 Not applicable 4 Free calcium oxide 1 per month or 1 per 10 000 t 4.2.4 Not applicable 5 Soundnessb1 per month or 1 per 10 000 t 4.2.4 4.3.2 6 Reactive calcium oxide 1 per month or 1 per 10 000 t Not applicable 4.3.3

43、 7 Water content 2 per month or 1 per 5 000 t 4.2.5 4.3.4 8 Pozzolanic activityb2 per year or 1 per 50 000 t 4.2.6 Not applicable 9 Hydraulic activityb2 per year or 1 per 50 000 t Not applicable 4.3.5 aWhich ever is more frequent. bIf required. 6 Marking and labelling The delivery ticket shall conta

44、in at least the following: a) reference to this European Standard; b) type of fly ash; c) origin; d) manufacturer. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, informat

45、ion and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government,

46、 consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all

47、sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying stand

48、ardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard cop

49、ies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in