BS EN 13981-2-2004 Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Plates and sheets《铝和铝合金 结构性轨道用.pdf

《BS EN 13981-2-2004 Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Plates and sheets《铝和铝合金 结构性轨道用.pdf》由会员分享，可在线阅读，更多相关《BS EN 13981-2-2004 Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Plates and sheets《铝和铝合金 结构性轨道用.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 13981-2:2004 Aluminium and aluminium alloys Products for structural railway applications Technical conditions for inspection and delivery Part 2: Plates and sheets The European Standard EN 13981-2:2004 has the status of a British Standard ICS 77.150.10 BS EN 13981-2:2004 This

2、British Standard was published under the authority of the Standards Policy and Strategy Committee on 4 August 2004 BSI 4 August 2004 ISBN 0 580 44200 4 National foreword This British Standard is the official English language version of EN 13981-2:2004. The UK participation in its preparation was ent

3、rusted by Technical Committee NFE/35, Light metals and their alloys, to Subcommittee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British S

4、tandards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.

5、This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible i

6、nternational/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the

7、EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN139812 July2004 ICS77.150.1

8、0 Englishversion AluminiumandaluminiumalloysProductsforstructuralrailway applicationsTechnicalconditionsforinspectionanddelivery Part2:Platesandsheets AluminiumetalliagesdaluminiumProduitspour applicationsferroviairesstructurellesConditions techniquesdecontrleetdelivraisonPartie2:Tleset tlespaisses

9、AluminiumundAluminiumlegierungenErzeugnissefr tragendeAnwendungenimSchienenfahrzeugbau TechnischeLieferbedingungenTeil2:PlattenundBleche ThisEuropeanStandardwasapprovedbyCENon6May2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an St

10、andardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadeb

11、ytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latv

12、ia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationina

13、nyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN139812:2004:EEN 13981-2:2004 (E) 2 Contents page Foreword3 1 Scope4 2 Normative references4 3 Terms and definitions .4 4 Ordering information.4 5 Requirements.5 5.1 Production and manufacturing processes .5 5.2 Quality assurance5 5

14、.3 Alloys, chemical composition and tempers5 5.4 Mechanical properties of rolled products .5 5.5 Freedom from surface defects .5 5.6 Tolerances on dimensions and form.5 6 Sampling and test methods5 7 Traceability.6 8 Marketing of products .6 9 Inspection certificate.6 10 Record keeping6 11 Packaging

15、.6 12 Application and use.7 13 Arbitration.7 Annex A (informative) Guidelines for application and use .8 A.1 Selection of alloys .8 A.1.1 General8 A.1.2 EN AW-6082 and EN AW-60618 A.1.3 EN AW-50838 A.1.4 EN AW-5754 and EN AW-54548 A.2 Fatigue Design.9 A.3 Welding.9 Bibliography 10 EN 13981-2:2004 (E

16、) 3 Foreword This document (EN 13981-2:2004) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo

17、rsement, at the latest by January 2005, and conflicting national standards shall be withdrawn at the latest by January 2005. Within its program of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 21 “Railways applications of aluminium and aluminium alloys“ to prepare the following standa

18、rd: EN 13981-2, Aluminium and aluminium alloys Products for structural railway applications Technical conditions for inspection and delivery Part 2: Plates and sheets. This standard is part of a set of four standards. The other standards deal with: Part 1: Extruded products Part 3: Castings Part 4:

19、Forgings According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

20、Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13981-2:2004 (E) 4 1 Scope This document specifies requirements for rolled products (plate and sheet) which contribute to the structural properties of th

21、e railcar bodyshell and of other major structural components. It specifies particular requirements regarding qualification, quality control, material properties and dimensional tolerances are specified. Furthermore, guidelines for application and use are given. NOTE Some of the products listed in th

22、e present standard may be subject to patent or patent applications, and their listing herein does not in any way imply the granting of a licence under such patent right. CEN/TC 132 affirms that it is its policy that in the case when a patentee refuses to grant licenses on standardised standard produ

23、cts under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated re

24、ferences, the latest edition of the referenced document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and delivery. EN 485-2, Aluminium and aluminium alloys Sheet, strip and plate Part 2: Mechanical pro

25、perties. EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products EN 485-4, Aluminium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on shape and dimensions for cold-rolled products. EN 515, Aluminium and al

26、uminium alloys Wrought products Temper designations. EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition. EN 10204, Metallic products Types of inspection documents. EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitio

27、ns Part 1: General terms. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 structural property property having a direct effect on the static and dynamic load carrying capability of a component or assembly 4 Ord

28、ering information Ordering information shall be formulated as specified in EN 485-1. Reference to this document (EN 13981-2) shall be made. If special requirements are stated in the order agreed between supplier and purchaser which differ from requirements specified or referenced in this document, t

29、hen these special requirements shall apply. EN 13981-2:2004 (E) 5 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified on the order, the production and manufacturing processes shall be left to the discretion of the manufacturer. Unless it is explicitly stated on the o

30、rder, no obligation shall be placed on the manufacturer to use the same processes for subsequent and similar orders. 5.2 Quality assurance The manufacturer shall establish and maintain a quality management system which should be at least equivalent to EN ISO 9001. The manufacturer shall be responsib

31、le for carrying out all inspections and tests required by this standard, prior to the shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall stipulate this at the time of placing the order. 5.3 Alloys, chemical composition and tempers Alloys shal

32、l be selected from the following: EN AW-5454, EN AW-5754; EN AW-5083; EN AW-6061; EN AW-6082; any other alloys shall be qualified according to a mutually agreed procedure which shall consider the intended joining technique and the intended use; the chemical compositions of these alloys are specified

33、 in EN 573-3. In addition, the lead (Pb) content of all 6xxx series alloys shall be limited to maximum 0,01 %; the tempers shall be selected from those specified in EN 485-2. Other tempers shall be qualified according to a mutually agreed procedure which shall consider the intended joining technique

34、 and the intended use; tempers are defined in EN 515. 5.4 Mechanical properties of rolled products Tensile strength, yield strength and elongation of plate and sheet shall conform to the requirements of EN 485-2 unless otherwise agreed upon between supplier and purchaser and stated on the order. 5.5

35、 Freedom from surface defects Surface quality shall comply with the requirements of EN 485-1. 5.6 Tolerances on dimensions and form The tolerances on dimensions and form are specified in EN 485-3 and EN 485-4. 6 Sampling and test methods Sampling and test methods shall comply with the requirements a

36、ccording to EN 485-1. EN 13981-2:2004 (E) 6 7 Traceability The supplier shall establish and maintain a system of identification and traceability of products at each stage of manufacture, inspection and delivery, including subcontracted operations and products, in order to be able to reconstitute the

37、 history of all relevant data and to attribute them to the products concerned. In particular, the system shall cover the following areas: origin of materials and agreed properties; manufacturing operations including heat treatment; inspection and testing. The system of traceability shall allow the i

38、dentification any piece subjected to the same operation of manufacture or inspection. 8 Marketing of products Unless otherwise specified on the order lots delivered shall be marked with at least the following indications: alloy designation; temper designation; nominal thickness; inspection lot numbe

39、r; manufacturers name or symbol. Marking shall be applied onto the packaging. If required by the purchaser, a more comprehensive or piecewise marking shall be agreed between supplier and purchaser at the time of placing the order. 9 Inspection certificate Unless otherwise indicated on the order the

40、supplier shall deliver an inspection certificate 3.1.B according to EN 10204 with at least the results of chemical analysis and the obtained mechanical properties. 10 Record keeping Unless otherwise specified on the order quality records of inspections and tests required by this document shall be ke

41、pt at least during 10 years after delivery. 11 Packaging The type of packaging shall comply with the requirements according to EN 485-1. EN 13981-2:2004 (E) 7 12 Application and use Plate and sheet according to this document are used for structural parts of railcar bodyshells. Annex A (informative)

42、gives guidelines for: the selection of alloys; the choice of a suitable design code; welding. 13 Arbitration In cases of dispute concerning the conformity with the requirements of this document or specification cited in the order, and before rejecting the products, testing and examination shall be c

43、arried out by an arbitrator chosen by mutual agreement between supplier and purchaser. The arbitrators decision shall be final. EN 13981-2:2004 (E) 8 Annex A (informative) Guidelines for application and use A.1 Selection of alloys A.1.1 General The choice of the suitable aluminium alloy is determine

44、d by a combination of the factors strength, durability, physical properties, weldability, formability and availability. A.1.2 EN AW-6082 and EN AW-6061 EN AW-6082 is one of the most widely used heat treatable alloy and often the principle structural alloy in many countries for welded and unwelded ap

45、plications. EN AW-6061 is also a widely used heat treatable alloy for welded and non-welded applications. Both alloys are normally used in the peak aged T6 or T651 temper. The choice of these alloys as a structural material is based on a favourable combination of the properties: high strength after

46、heat treatment, good corrosion resistance, good weldability by both the MIG and the TIG processes, good formability in the T4 or T451 temper and good machinability. Care should be taken to account for the loss of strength in the heat affected zone (HAZ) of welded joints. Filler metals for welding ar

47、e specified in EN 1011-4. A.1.3 EN AW-5083 Among the alloys specified in the present standard EN AW-5083 is the strongest non-heat treatable alloy according to EN 485-2 possessing good welded properties and very good corrosion resistance. It is ductile in the soft condition with good forming propert

48、ies but looses ductility with cold forming, and can become hard with low ductility. This alloy is used commonly in Hxx tempers. However the alloy may in some tempers be susceptible to intergranular corrosion, which under certain circumstances, can develop into stress corrosion cracking under sustained loading. The use of this alloy is not recommended where the material is to be subjected to further heavy cold working and/or where service temperatures are expecte