BS EN 13672-2004 Surfaces for sports areas - Determination of resistance to abrasion of non-filled synthetic turf《运动场表面 非填装人工草皮的抗摩擦测定》.pdf

《BS EN 13672-2004 Surfaces for sports areas - Determination of resistance to abrasion of non-filled synthetic turf《运动场表面 非填装人工草皮的抗摩擦测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13672-2004 Surfaces for sports areas - Determination of resistance to abrasion of non-filled synthetic turf《运动场表面 非填装人工草皮的抗摩擦测定》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 13672:2004 Surfaces for sports areas Determination of resistance to abrasion of non-filled synthetic turf The European Standard EN 13672:2004 has the status of a British Standard ICS 97.220.40 BS EN 13672:2004 This British Standard was published under the authority of the Stan

2、dards Policy and Strategy Committee on 18 August 2004 BSI 18 August 2004 ISBN 0 580 44309 4 National foreword This British Standard is the official English language version of EN 13672:2004. The UK participation in its preparation was entrusted to Technical Committee PRI/57, Surfaces for sports area

3、s, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under th

4、e section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicat

5、ion. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monit

6、or related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last

7、issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN13672 August2004 ICS Englishversion SurfacesforsportsareasDeterminationofresistanceto abrasionofnonfilledsyntheticturf SolssportifsDterminationdelarsistancelabrasion desgazonssynthtique

8、snonchargs SportbdenBestimmungdesVerschleiverhaltensvon ungeflltemKunststoffrasen ThisEuropeanStandardwasapprovedbyCENon14June2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteratio

9、n.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoi

10、tsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Pola

11、nd,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMe

12、mbers. Ref.No.EN13672:2004:EEN 13672:2004 (E) 2 Contents page Foreword3 1 Scope4 2 Normative references4 3 Terms and definitions .4 4 Principle4 5 Apparatus.4 6 Sampling and preparation of test pieces 4 7 Conditioning.4 8 Procedure.5 9 Calculation and expression of results.5 10 Test report5 EN 13672

13、:2004 (E) 3 Foreword This document (EN 13672:2004) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endor

14、sement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the latest by February 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel

15、gium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13672:2004 (E) 4 1 Scope This documen

16、t describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions. It is applicable to non-filled synthetic turf with a pile height greater than 15 mm. 2 Normative references The following referenced documents

17、 are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 5470-1, Rubber- or plastics-coated fabrics Determination of abrasion resista

18、nce Taber abrader (ISO 5470-1:1999). 3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1 wear resistance loss of mass from the pile of synthetic turf 4 Principle A test piece is abraded by the action of a pair of abrasive wheels on a rotating tes

19、t piece. The resulting loss in mass is determined. 5 Apparatus 5.1 Abrasion apparatus, as specified in EN ISO 5470-1. 5.2 Freshly re-faced abrasive wheels H18, acting under a load of 1 000 g per wheel. 5.3 Re-facing disc S11. 5.4 Balance, capable of weighing to an accuracy of 0,001 g. 6 Sampling and

20、 preparation of test pieces Take four test pieces with edge length of 100 mm across the sample, not closer than 200 mm to the edge of the sample. Remove any loose particles from the test pieces. 7 Conditioning Condition the test pieces for a minimum of 3 h at the test temperature. If the material is

21、 known to be sensitive to humidity, condition for a minimum of 48 h at standard temperature and relative humidity. EN 13672:2004 (E) 5 Unless otherwise specified, the standard temperature shall be (23 2) C and the standard relative humidity shall be (50 5) %. 8 Procedure 8.1 Weigh the test piece to

22、an accuracy of 0,001 g. 8.2 Before each test, re-face the abrasive wheels using re-facing disc S11. 8.3 Position the test piece in the abrasion apparatus (5.1). Lower the loaded abrasive wheels onto the surface of the test piece and start the machine. After 2 000 revolutions stop the machine. Remove

23、 the test piece from the machine. Remove any loose debris from the test piece by vacuuming. Re-weigh the test piece. Re-face the abrasive wheels with re-facing disc . Repeat this procedure after further 3 000 revolutions so that the test piece is subjected to a total of 5 000 revolutions. 8.4 Repeat

24、 the procedure on the other three test pieces. 9 Calculation and expression of results Record the mass loss after 2 000 and 5 000 revolutions for each test piece. Calculate the arithmetic mean of the mass loss for the four test pieces after 2 000 and 5 000 revolutions. Express the results in absolut

25、e figures to the nearest of 0,01 g and as the percentage mass loss to the nearest of 0,01 %. 10 Test report The test report shall include the following information: a) reference to this document, i.e. EN 13672:2004; b) complete identification of the product tested, including type, source, colour, ma

26、nufacturers reference and previous history; c) method of sampling; d) test temperature and relative humidity, if required; e) arithmetic mean of the mass loss after 2 000 and 5 000 revolutions, expressed in grams and as a percentage. BS EN 13672:2004 BSI 389 Chiswick High Road London W4 4AL BSI Brit

27、ish Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of B

28、ritish Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of

29、the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.

30、Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for intern

31、ational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Tec

32、hnical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date wi

33、th standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standar

34、ds via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodi

35、es. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free

36、use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.