BS EN 13617-4-2012 Petrol filling stations Safety requirements for construction and performance of swivels for use on metering pumps and dispensers《加油站 计量泵和配油器用转环的建造和性能的安全性要求》.pdf

《BS EN 13617-4-2012 Petrol filling stations Safety requirements for construction and performance of swivels for use on metering pumps and dispensers《加油站 计量泵和配油器用转环的建造和性能的安全性要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13617-4-2012 Petrol filling stations Safety requirements for construction and performance of swivels for use on metering pumps and dispensers《加油站 计量泵和配油器用转环的建造和性能的安全性要求》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13617-4:2012Petrol filling stationsPart 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensersBS EN 13617-4:2012 BRITIS

2、H STANDARDNational forewordThis British Standard is the UK implementation of EN 13617-4:2012. It supersedes BS EN 13617-4:2004, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e P V E / 3 9 3 / 4 , M e t e r i n g p u m p s a n d d i s p

3、e n s e r s for liquid fuel.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution

4、2012Published by BSI Standards Limited 2012ISBN 978 0 580 71241 8 ICS 75.200 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2012.Amendments issued sinc

5、e publicationDate T e x t a f f e c t e dBS EN 13617-4:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13617-4 March 2012 ICS 75.200 Supersedes EN 13617-4:2004English Version Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on meterin

6、g pumps and dispensers Stations-service - Partie 4: Exigences relatives la construction et aux performances de scurit des raccords tournants utiliss sur les distributeurs de carburants Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken fr Zapfsulen un

7、d druckversorgte Zapfsulen This European Standard was approved by CEN on 28 January 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date li

8、sts and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation unde

9、r the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

10、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITE

11、E FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13617-4:2012: EBS EN 13617-4:2012EN 13617-4:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 4

12、3 Terms and definitions .54 Explosion protection measures .55 Construction .55.1 General 55.2 Connection threads .65.3 Safe breaks .66 Physical properties 67 Functional requirements .78 Frequency of testing .79 Information for use 89.1 General 89.2 Marking and instruction 8Annex A (normative) Testin

13、g .9A.1 General 9A.2 Fuel compatibility pre-conditioning .9A.3 Endurance 9A.4 Electrical resistance test 10A.5 Burst test . 10A.6 Drop test 10A.7 Leak test 10Annex B (informative) Environmental aspects 11Annex ZA (informative) Relationship between this European Standard and the Essential Requirement

14、s of EU Directive 94/9/EC . 13BS EN 13617-4:2012EN 13617-4:2012 (E) 3 Foreword This document (EN 13617-4:2012) has been prepared by Technical Committee CEN/TC 393 “Equipment for tanks and filling stations”, the secretariat of which is held by DIN. This European Standard shall be given the status of

15、a national standard, either by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subje

16、ct of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13617-4:2004. According to edition EN 13617-4:2004 the following fundamental changes are given: a new note at the end of the scope: Fuels other than of Exp

17、losion Group IIA are excluded from this European Standard added; informative Annex B concerning environmental aspects added. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements o

18、f EU Directives. For relationship with EU Directives, see informative Annex ZA, which is an integral part of this standard. The present standard is composed of the following parts: Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units; Pa

19、rt 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers; Part 3: Safety requirements for construction and performance of shear valves; Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and disp

20、ensers. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

21、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13617-4:2012EN 13617-4:2012 (E) 4 1 Scope This European Standard specifies safety requirements for the construct

22、ion and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1. It pays pa

23、rticular attention to electrical, mechanical and hydraulic characteristics of swivels. The requirements apply to swivels at ambient temperatures from 20 C to +40 C with the possibility for an extended temperature range. This European Standard applies mainly to hazards related to the ignition of liqu

24、id fuels being dispensed or their vapour. This European Standard also addresses electrical and mechanical hazards of swivels. This European Standard is not applicable to swivels for the dispensing of any compressed gas. NOTE 1 This European Standard does not apply to equipment for use with liquefied

25、 petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas (CNG). NOTE 2 Fuels other than of Explosion Group IIA are excluded from this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indis

26、pensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 228, Automotive fuels Unleaded petrol Requirements and test methods EN 11271, Explosive atmospheres Explosi

27、on prevention and protection Part 1: Basic concepts and methodology EN 1360, Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems Specification EN 13012:2001, Petrol filling stations Construction and performance of automatic nozzles for use on fuel dispensers EN 13463-1:

28、2009 Non-electrical equipment for use in potentially explosive atmospheres Part 1: Basic method and requirements EN 13483, Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems Specification prEN 136171:2010 Petrol filling stations Part 1: Sa

29、fety requirements for construction and performance of metering pumps, dispensers and remote pumping units EN 13617-2:2012, Petrol filling stations Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers EN 60079-0, Explosive atmospheres Pa

30、rt 0: Equipment General requirements EN ISO 2281, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) EN ISO 1825, Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling Specification (ISO 1825) BS EN 1

31、3617-4:2012EN 13617-4:2012 (E) 5 EN ISO 8031:2009, Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity (ISO 8031:2009) ISO 261, ISO general-purpose metric screw threads General plan ISO 9652, ISO general purpose metric screw threads Tolerances Part 2

32、: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 119253, Reaction to fire tests Ignitability of building products subjected to direct impingement of flame Part 3: Multi-source test 3 Terms and definitions For the purposes of this document, the terms and de

33、finitions given in EN 13012:2001, prEN 136171:2010 and EN 136172:2012 and the following apply: 3.1 swivel device fitted between nozzle and metering pump or dispenser to allow rotational movement 3.2 single plane swivel swivel with one plane of rotation 3.3 dual plane swivel swivel with two planes of

34、 rotation 4 Explosion protection measures 4.1 Explosion protection measures shall be taken in accordance with EN 1127-1 and Annex B of EN 13617-1:2012. 4.2 The swivel shall be explosion protected and shall be Category 2 in accordance with EN 134631. The vapour path of a vapour recovery swivel shall

35、be Category 1 in accordance with EN 134631. The swivel shall fulfil the requirements for temperature Class T3 and Group IIA to EN 60079-0 or EN 134631. 5 Construction 5.1 General All electrical and non-electrical equipment and components, intended for use in potentially explosive atmospheres, shall

36、be designed and constructed according to good engineering practice and in conformity with the required categories for Group II equipment to ensure avoidance of any ignition source. To classify the category of the equipment it shall be subjected to an ignition hazard assessment in accordance with 5.2

37、 of EN 13463-1:2009. Materials used in the construction shall be chemically and dimensionally stable under known service conditions. Materials likely to come into contact with fuels in both liquid and vapour phases shall be resistant to attack by these fuels. Conformity shall be demonstrated by manu

38、facturers declaration and by the tests detailed in Annex A. Light alloys when used shall conform to the requirements of 6.4.4.2 of EN 134631:2009. If other specifications for explosion protected equipment impose more stringent requirements then the more stringent requirement shall apply. BS EN 13617

39、-4:2012EN 13617-4:2012 (E) 6 All components shall be of corrosion resistant material or shall be provided with a corrosion resistant protective coating. Outside surfaces likely to be handled shall be free of sharp edges. If protective covers are fitted they shall be constructed so that they allow ve

40、ntilation and evaporation of fuel even if some shrinkage occurs. They shall not affect the performance of the swivels. The sealing surfaces of the connection threads shall be designed such that they are suitable for use with an enclosed O-ring or flat gasket. 5.2 Connection threads Connection thread

41、s shall be one of the following styles: Style 1 Swivels without a vapour recovery path shall use parallel threads in accordance with EN ISO 2281. The connection thread dimensions shall be in accordance with Table 1 Table 1 Thread specifications Nominal connection size Inch Female threadsMaximum thre

42、ad depthamm Male threads Minimum thread lengthbmm ” 12,5 11,01” 15,5 14,01 ” 15,5 17,5 1 ” 15,5 18,0 aThe thread depth, measured from the outer fore-part to the metallic inner sealing face. bThe stated minimum length only applies if the female thread of the connection fitting includes an inner flat

43、gasket. When no inner flat gasket is used the minimum thread length depends on the tightness requirements of the threaded connection. Style 2: Swivels with a vapour recovery path shall use M 34 x 1,5 male outlet threads according to ISO 261 and ISO 965-2. The total thread length shall be maximum 15,

44、0 mm. The inlet end shall be machined to a diameter of (35,0 0,05) mm for a length (6,0 0,1) mm. 5.3 Safe breaks If a swivel has an integral safe break it shall fulfil the requirements of EN 136172. 6 Physical properties The physical properties of the swivel shall conform to the requirements given i

45、n Table 2 when tested by the methods indicated. BS EN 13617-4:2012EN 13617-4:2012 (E) 7 Table 2 Physical properties of swivel Property Requirement Test method Electrical resistance between inlet and outlet when assembled. 105 A.4 Electrostatic properties 6.7 EN 13463-1:2009 EN 13463-1 Fuel compatibi

46、lity 5.1 A.2 followed by A.6, A.7 and A.5Endurance Clause 6 and electrical resistance test 105 after endurance test A.3 Ignitability of composites on the swivel. Ignition source C; Effect time 20 s; Surface flame impingement The material tested shall not flame ISO 119253 Characteristics of swivel co

47、mponents and/or covers to prevent dangerous, mechanically generated, sparks (resistance to sparking). 6.4.4.2 EN 134631:2009 EN 134631 7 Functional requirements The swivel shall comply with the operational requirements of Table 3 when tested by the indicated methods; and with a frequency of testing

48、as specified in Clause 8 and Table 4. Table 3 Operational requirements Test Test method Requirement Burst test A.5 No catastrophic damage. Drop test A.6 No permanent deformation of the swivel leading to malfunction. Leak test A.7 No quantifiable sign of leakage visible to an eye with normal visual a

49、cuity. 8 Frequency of testing Testing shall be performed in accordance with the schedule given in Table 4. A total of five swivels shall be subjected to the type tests. One swivel for type test shall be tested according to A.3 followed by functional requirements under Clause 7. Four swivels for type test shall be pre-conditioned according to A.2. The drop test according to A.6 shall be done immediately after removal from saturated atm