BS EN 13247-2001 Packaging - Specification for tensional strapping for lifting lashing and securing of loads《装运 固定货物用提升系紧绳规范 》.pdf

《BS EN 13247-2001 Packaging - Specification for tensional strapping for lifting lashing and securing of loads《装运 固定货物用提升系紧绳规范 》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13247-2001 Packaging - Specification for tensional strapping for lifting lashing and securing of loads《装运 固定货物用提升系紧绳规范 》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 13247:2001 Packaging Specification for tensional strapping for lifting, lashing and securing of loads The European Standard EN 13247:2001 has the status of a British Standard ICS 55.040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 13247:2001 This

2、 British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 2001 BSI 05-2001 ISBN 0 580 37223 5 National foreword This British Standard is the official

3、 English language version of EN 13247:2001. The UK participation in its preparation was entrusted by Technical Committee PKW/5, Primary and transport packaging, to Subcommittee PKW/5/33, Tensional strapping, taping and accessories, which has the responsibility to: A list of organizations represented

4、 on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence

5、 Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itse

6、lf confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them

7、 in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. N

8、o. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN13247 March2001 ICS55.040 Englishversion PackagingSpecificationfortensionalstrappingforlifting, lashingandsecuringofloads EmballageSpcificationsrelativesauxcerclagesdacier pourlelevage,larrimageetlafixationdescharges VerpackungSpezifik

9、ationfrUmreifungsbnderausStahl zumHeben,BindenundSichernvonLadungen ThisEuropeanStandardwasapprovedbyCENon4February2001. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatel

10、istsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguage

11、andnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMIT

12、TEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2001CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN13247:2001EPage2 EN13247:2001 Contents Page Foreword3 1 Scope 4 2 Normat

13、ivereferences 4 3 Dimensionsandmechanicalproperties 4 4 Physicalproperties. .5 5 Marking .5 AnnexA (informative) Finishing . .8Page3 EN13247:2001 Foreword ThisEuropeanStandardhasbeenpreparedbyTechnicalCommitteeCEN/TC261“Packaging“,thesecretariatof whichisheldbyAFNOR . ThisEuropeanStandardshallbegive

14、nthestatusofanationalstandard,eitherbypublicationofanidenticaltextor byendorsement,atthelatestbySeptember2001,andconflictingnationalstandardsshallbewithdrawnatthe latestbySeptember2001. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsofthefollowing countriesareboundtoim

15、plementthisEuropeanStandard:Austria,Belgium,CzechRepublic,Denmark,Finland, France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden, SwitzerlandandtheUnitedKingdom.Page4 EN13247:2001 1Scope ThisEuropeanstandardspecifiesdimensions,physicalpropertiesandspecialreq

16、uirementsforTensional SteelStrappingusedforlifting,lashingandsecuringofloads. Thissteelstrappingformspartofacompletesystemofequipment,sealsandstrappingandmaybeused accordingtotheinstructionsissuedbythemanufacturer,whichincorporateallthesystemrequirements. NOTE Technicalsafetyregulationsoftheindividu

17、almemberstatesshouldbetakenintoaccount. 2 Normativereferences ThisEuropeanStandardincorporatesbydatedorundatedreference,provisionsfromotherpublications. Thesenormativereferencesarecitedattheappropriateplacesinthetextandthepublicationsarelisted hereafter.Fordatedreferences,subsequentamendmentstoorrev

18、isionsofanyofthesepublicationsapply tothisEuropeanStandardonlywhenincorporatedinitbyamendmentorrevision.Forundatedreferences thelatesteditionofthepublicationreferredtoapplies(includingamendments). EN100021 MetallicmaterialsTensiletestingPart1:Methodoftestat(ambienttemperatures) 3 Dimensionsandmechan

19、icalproperties 3.1Width ThewidthofthetensionalsteelstrappingshallbewithinthespecifiedrangeasshowninTable1. Table1Widthrange Range(mm) Nominalwidth mm From to 31,75 31,60 32,00 3.2Thickness ThethicknessofthetensionalsteelstrappingshallbewithinthespecifiedrangeasshowninTable2. Table2Thicknessrange Nom

20、inalthicknessmm Rangemm F rom to 0,79 0,79 0,87 1,12 1,12 1,22 1,27 1,27 1,37 1,45 1,45 1,55Page5 EN13247:2001 3.3Breakingstrength TheminimumbreakingstrengthofthetensionalsteelstrappingshallbeasspecifiedinTable3,whentested inaccordancewithEN100021,usingatestpieceoftheoriginalstrappingusingagaugeleng

21、thof100mm. Table3Minimumbreakstrength Size mm Minimumbreakstrength kN 31,75 0,79 25 31,75 1,12 38 31,75 1,27 43 31,75 1,45 49 3.4Elongationatbreak Elongationatbreakshallbegreaterthan7%,measuredusingagaugelengthof100mm,whentestedin accordancewithEN100021. 4 Physicalproperties Physicalpropertiesforten

22、sionalsteelstrappingareshowninTables1to3, 4.1Camber Cambershallnotexceed10mmper2000mmmaximum(Seefigure1). 4.2Curl Endsshallnotliftmorethan40mmper2000mmmaximum(Seefigure1). 4.3Twist Shallnotexceed30degreesin2000mmmaximum(Seefigure1). 4.4Edgefinish Edgesshallbeproperlyfinishedtoeliminateburrsandsharpe

23、dges. 4.5Productionwelds Nonepermitted. 5Marking 5.1 Thethickness,andminimumbreakingstrengthandnameofthemanufacturerofthetensionalsteel strappingshallbemarkedbycirclesorcirclesplustheletter“M“asshowninTable4. 5.2 Thefirstletterofthemanufacturersbrandnameshallbeprintedinsidethecircle.Thislettershallb

24、e aslargeaspossibleandhaveathicknessofatleast2mm.The“M“shallbesimilarlyprinted.Page6 EN13247:2001 5.3 Thismarkingshallberepeatedevery500mmto1000mmalongthelengthofthetensionalsteel strapping. Table4Markingoftensionalsteelstrapping Size mm Marking 31,75 0,79 0 31,75 1,12 00 31,75 1,27 000 31,75 1,45 0

25、00MPage7 EN13247:2001 Key 1 AmountofCamber10mmmaximum 2 Camber 3C u r l 4T w i s t Figure1Tolerancesper2000mmlengthPage8 EN13247:2001 AnnexA (informative) Finishing Surfacefinish A.1 General Tensionalsteelstrappingcanbeavailableinachoiceofsurfacefinishaccordingtothespecialrequirements necessaryforag

26、ivenapplication NOTE Usersareadvisedtocheckwiththesuppliersthatthefinishtheyrequirecanbesuppliedforthetype,size andqualityofstrappingthattheyareordering. A.2 Paintedandwaxed Variouscoatingareusedtoprovideadegreeofresistancetocorrosionorchemicalreactionbetweenthe strappingandthesurfaceofthegoodsbeing

27、strapped.Waxcanbeappliedtothesurfacetoimprove tensioningability. A.3 Paintedonly Variouscoatingsareusedtoprovideadegreeofresistancetocorrosionorchemicalreactionbetweenthe strappingandthesurfaceofthegoodsbeingstrapped. Thesurfaceshouldbefreeofalldepositswhichhavealubricatingeffectwhichwouldresultinre

28、ductionof jointstrength.blankBS EN 13247:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated

29、 by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone find

30、ing an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS whic

31、h ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website

32、 at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and int

33、ernational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI

34、 are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at h

35、ttp:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sys

36、tem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If t

37、hese details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.