BS EN 13044-2-2011 Intermodal loading units Marking Markings of swap bodies related to rail operation《联合运输负载单元 标记 关于铁轨操作的可拆卸车体的标记》.pdf

《BS EN 13044-2-2011 Intermodal loading units Marking Markings of swap bodies related to rail operation《联合运输负载单元 标记 关于铁轨操作的可拆卸车体的标记》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13044-2-2011 Intermodal loading units Marking Markings of swap bodies related to rail operation《联合运输负载单元 标记 关于铁轨操作的可拆卸车体的标记》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13044-2:2011Intermodal Loading Units MarkingPart 2: Markings of swap bodies related torail operationBS EN 13044-2:2011 BRITISH STANDARDNational forewordThis British Standar

2、d is the UK implementation of EN 13044-2:2011.Together with BS EN 13044-1:2011 and BS EN 13044-3:2011, itsupersedes BS EN 13044:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee TW/1, Freight containers and swap bodies.A list of organizations represe

3、nted on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 64614 0ICS 35.240.60; 55.180.10Compliance with a British Standard cannot

4、confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2011.Amendments issued since publicationDate Text affectedBS EN 13044-2:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13044-2 January

5、2011 ICS 35.240.60; 55.180.10 Supersedes EN 13044:2000English Version Intermodal Loading Units - Marking - Part 2: Markings of swap bodies related to rail operation Units de chargement intermodales - Marquage - Partie 2: Marquages des caisses mobiles pour lexploitation sur railIntermodale Ladeeinhei

6、ten - Kennzeichnung - Teil 2: Kennzeichnungen von Wechselbehltern fr den Bahnbetrieb This European Standard was approved by CEN on 30 November 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status o

7、f a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German

8、). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia,

9、Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATIO

10、N COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13044-2:2011: EBS EN 13044-2:2011EN 13044-2:2011 (E) 2 Conten

11、ts Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .64 Operational markings 64.1 Purpose of the operational markings 64.2 Structure of the operational marking.65 Location of the marking 96 Assignment of the profile code 97 Allocation bodies for coding and their

12、 responsibilities 98 Other operational marks .98.1 General 98.2 Maximum gross and tare masses . 108.3 Warning sign for not allowed stacking configurations. 108.4 Warning; Electricity 109 Design of the markings 109.1 Size and colour of the markings . 109.2 Display and location of the markings . 109.2

13、.1 General . 109.2.2 Location . 10Annex A (normative) Warning; Electricity . 11Bibliography . 12BS EN 13044-2:2011EN 13044-2:2011 (E) 3 Foreword This document (EN 13044-2:2011) has been prepared by Technical Committee CEN/TC 119 “Swap bodies for combined goods transport”, the secretariat of which is

14、 held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2011, and conflicting national standards shall be withdrawn at the latest by July 2011. Attention is drawn to the possibility tha

15、t some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13044:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations

16、 of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, R

17、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 13044-2:2011EN 13044-2:2011 (E) 4 Introduction This European Standard contains the recommended method of marking Intermodal Loading Units (ILU) to meet current and future requirements. This European Standard follows

18、 the format used in EN ISO 6346, the worldwide accepted standard for marking and coding of marine freight containers. As the above standard can be applied, without alteration, to an ILU, the standard is not directly interchangeable with the ISO standard. However, since the ILU are handled and transp

19、orted in Europe in the same environment as ISO freight containers, the two standards are compatible. BS EN 13044-2:2011EN 13044-2:2011 (E) 5 1 Scope This European Standard provides a system for the identification and presentation of information about the ILU. The identification system is intended fo

20、r general application, for example in documentation, control and communication (including automatic data processing systems), as well as for display on the ILU and other non ISO containers (i.e. which dimensions and testing parameters differ from those defined by the applicable ISO standards) used i

21、n European transport. The methods of displaying identification and specific other data (including operational data) on the ILU by means of permanent marks are included. This European Standard specifies: a) an ILU identification system with an associated system for verifying the accuracy of its use,

22、having mandatory marks for the presentation of the identification system for visual interpretation; and b) a coding system for data on ILU size, with corresponding marks for their display; c) mandatory operational marks; d) physical presentation of the marks on the ILU. This part of the European Sta

23、ndard prescribes the system of operational data for the codification of the swap bodies. The codification assigns a maximum profile for the cover area available at the rail tracks to the swap bodies in order to enable the selection of those rail tracks on which these swap bodies can be transported w

24、ithout any danger. This part of the European Standard prescribes furthermore the additional operational markings, which are necessary for railway operation. This European Standard does not cover temporary operational marks of any kind, permanent marks, data plates, etc. which may be required by inte

25、rgovernmental agreements, national legislation or non-governmental organisations other than CEN. NOTE Some of the major international conventions whose container-marking requirements are not covered in this European Standard are as follows: International Convention for Safe Containers (UN/IMO 1992);

26、 Customs Convention on Containers 1956 and 1972; Customs Convention on International Movement of Goods under Cover of TIR Carnets (TIR-Convention) 1959 and 1975. It should not be assumed that this list is exhaustive. This European Standard does not cover the display of technical data on Swap tanks (

27、see EN 1432) nor does it, in any way, include identification marks or safety signs for items of cargo which may be carried in swap bodies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

28、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. BS EN 13044-2:2011EN 13044-2:2011 (E) 6 EN 12642, Securing of cargo on road vehicles Body structure of commercial vehicles Minimum requirements EN 13044-1, Swap bodies Marking Part 1: Mar

29、kings for identification CEN/TS 13853, Swap bodies for combined transport Stackable swap bodies type C 745-S16 Dimensions, design requirements and testing UIC 596-6, Conveyance of road vehicles on wagons Technical organisation Conditions for coding combined-transport load units and combined-transpor

30、t lines 3 Terms and definitions For the purposes of this document, the following term and definition apply. 3.1 Intermodal Loading Unit ILU loading unit suitable for European intermodal transport on road, rail, inland waterway and sea, which is not an ISO-container according to ISO 830 EXAMPLE Among

31、st others swap body, semi-trailer. 4 Operational markings 4.1 Purpose of the operational markings The operational marking covers the information for codification and for approval of the swap bodies for transportation within the European railway network. The assignment of the operational markings inc

32、ludes: the approval of the swap bodies to be transported on the European railway network; the assignment of a profile code according to UIC 596-6 for these specific swap bodies. It is up to the owner of the swap body to choose a horizontal or vertical plate according to the geometry (shape) of the u

33、nit or to the place available. 4.2 Structure of the operational marking A swap body shall be marked according to Figure 1 and Figure 2. The marking with a two-digit profile number is valid for swap bodies having a width equal to or less than 2 550 mm, or a three-digit profile number is valid for swa

34、p bodies having a width greater than 2 550 mm but not more than 2 600 mm. BS EN 13044-2:2011EN 13044-2:2011 (E) 7 Figure 1 Shape and content of the operational marking with a 2 or 3-digit profile number on a vertical plate The items of the marking have the following meaning: the code for the railway

35、 profile according to UIC 596-6 in connection with S or C; two digit length code of the swap bodies according to Table 1 and Table 2; the width class of the swap bodies in mm (2 500, 2 550 or 2 600); indicates the strength of the swap bodies body, standard or reinforced with the marking referring to

36、 EN 12642. The left part of the marking contains all information about the approval of the swap bodies for the transport on the railway network. The meaning of the numerals is as follows: the leading 3 digits are coding the authorised body, which has certified the approval, according to UIC 596-6; t

37、he following 6 digits, separated by a dot are coding the case number assigned by the certification body; the last characters, separated by a dot representing the body frame number of the swap bodies. BS EN 13044-2:2011EN 13044-2:2011 (E) 8 Figure 2 Shape and content of the operational marking with a

38、 2 or 3-digit profile number on a horizontal plate Table 1 Coding of the swap bodies length for symmetrical dimensions Length code Maximum length (mm) Maximum projection (mm) Distance of corner casting centre points (mm) Maximum projection (mm) 20 6 058 101,5 5 853 3 101,5 21 6 250 198,5 5 853 3 198

39、,5 22 7 150 648,5 5 853 3 648,5 23 7 450 798,5 5 853 3 798,5 24 7 820 983,5 5 853 3 983,5 26 8 150 1 148,5 5 853 3 1 148,5 30 9 125 101,5 8 918 4 101,5 31 9 300 191,0 8 918 4 191,0 40 12 192 101,5 11 985 4 101,5 42 12 500 257,5 11 985 4 257,5 44 13 100 557,5 11 985 4 557,5 45 13 716 865,5 11 985 4 8

40、65,5 BS EN 13044-2:2011EN 13044-2:2011 (E) 9 Table 2 Coding of the swap bodies length for asymmetrical dimensions Length code Maximum length (mm) Maximum projection (mm) Distance of corner casting centre points (mm) Maximum projection (mm) 60 8.543 1.190 5 853 3 1.500 81 9.275 101,5 8.918 4 253,5 82

41、 9.330 101,5 8.918 4 308,5 84 10.040 101,5 8.918 4 1.018,5 85 10.200 101,5 8.918 4 1.178,5 86 10.900 101,5 8.918 4 1.878,5 91 12.500 101,5 11.985 4 411,5 94 12.750 101,5 11.985 4 661,5 95 13.200 257,5 11.985 4 957,5 96 13.600 715 11.985 4 900 97 14.040 715 11.985 4 1.340 5 Location of the marking Th

42、e marking plates shall be fixed on each side wall of the swap bodies, preferably at the lower area near the front end (see also EN 13044-1). 6 Assignment of the profile code The assignment of the profile code shall be according to UIC 596-6. 7 Allocation bodies for coding and their responsibilities

43、The allocation and assignment of the operational markings for the codification of the swap bodies according to Figure 1 or Figure 2 shall be done only by a Railway Undertaking (RU) certified in Europe or any other approved authority in the country concerned. Operational markings for codification of

44、swap bodies shall only be assigned for swap bodies fulfilling all tests according to EN 283. The allocation body is obliged to document the assignment of the codification to the specific swap bodies for later checks. 8 Other operational marks 8.1 General The marks in this section are not intended to

45、 correspond to any particular code (e.g. for use in data transmission or any other purpose). They are solely intended as markings for use on swap bodies to convey specific information or give visual warnings. BS EN 13044-2:2011EN 13044-2:2011 (E) 10 8.2 Maximum gross and tare masses Swap bodies, whi

46、ch will be transported on inland waterways and by sea, shall be mandatory marked with the maximum gross mass and the tare mass in kilogram (kg). For other transport modes for swap bodies these marks are optional. These marks shall be displayed at the door end as follows: MAX GROSS 00 000 kg TARE 00

47、000 kg 8.3 Warning sign for not allowed stacking configurations A stackable swap body that does not meet all requirements of ISO 1496 for stack ability shall be marked with a warning sign according to CEN/TS 13853. 8.4 Warning; Electricity All swap bodies equipped with ladders shall display a warnin

48、g sign in accordance with the details given in Annex A. 9 Design of the markings 9.1 Size and colour of the markings Letters and numbers for MAX GROSS and TARE shall have a minimum size of 50 mm. Width and height of all digits shall have a suitable proportion to each other and the colour shall be in

49、 contrast in relation to the colour of the swap bodies. NOTE It is recommended to use white or black for the letters and numerals. 9.2 Display and location of the markings 9.2.1 General The requirements of this clause are especially related to swap bodies with solid structure (box type). Display and location of markings for other swap bodies types shall follow these rules as far as possible. NOTE I