BS EN 130200-1993 Harmonized system of quality assessment for electronic components - Sectional specification fixed tantalum capacitors with non-solid or solid electrolyte《电子元器件质量评.pdf

《BS EN 130200-1993 Harmonized system of quality assessment for electronic components - Sectional specification fixed tantalum capacitors with non-solid or solid electrolyte《电子元器件质量评.pdf》由会员分享，可在线阅读，更多相关《BS EN 130200-1993 Harmonized system of quality assessment for electronic components - Sectional specification fixed tantalum capacitors with non-solid or solid electrolyte《电子元器件质量评.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 130200:1993 Incorporating Amendment No. 1 Harmonized system of quality assessment for electronic components Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte The European Standard EN 130200:1993, with the incorporation of its amendment A3:1

2、998, has the status of a British Standard ICS 31.060.40BSEN130200:1993 This British Standard, having been prepared under the directionof the Electronic Components Standards PolicyCommittee, was publishedunder the authorityofthe Standards Board andcomes into effect on 15 December 1993 BSI 06-1999 The

3、 following BSI references relate to the work on this standard: Committee reference ECL/4 Special announcement in BSI News, September 1993 ISBN 0 580 22727 8 Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard

4、 was prepared, comprises the national committees of the following countries: Austria Italy Belgium Luxembourg Denmark Netherlands Finland Norway France Portugal Germany Spain Greece Sweden Iceland Switzerland Ireland United Kingdom Amendments issued since publication Amd. No. Date Comments 10078 Jan

5、uary 1999 See foreword to amendment A3 on page 2 NOTEThere was no amendment 1 to EN 130200BSEN130200:1993 BSI 06-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN 130200 5 National annex NA (informative) Committees responsible Inside back co

6、ver National annex NB (informative) Cross-references Inside back coverBSEN130200:1993 ii BSI 06-1999 National foreword This British Standard has been prepared under the direction of the Electronic Components Standards Policy Committee. It is the English language version of EN 130200:1993 Harmonized

7、system of quality assessment for electronic components. Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte, including amendment A3:1998 published by the Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC)

8、. Amendment A3 incorporates amendment A2. It supersedes BS CECC 30200:1986 which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does

9、not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 24, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendment

10、s incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 130200 June 1993 + A3 March 1998 Supersedes CECC 30 200Issue 2:1985 Descriptors: Quality, electronic components, capacitors English version Sectional Specificat

11、ion: Fixed Tantalum Capacitors with Non-Solid or Solid Electrolyte (includes amendment A3:1998) Spcification intermdiaire: Condensateurs fixes au tantale lectrolyte non solide ou solide (inclut lamendement A3:1998) Rahmenspezifikation: Tantal-Festkondensatoren mit festem oder flussigemElektrolyten (

12、enthlt nderung A3:1998) This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on 27 January 1992; amendment A3 was approved by CENELEC on 1994-10-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

13、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three officia

14、l versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committ

15、ees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. The membership of the CECC is identical, with the exception of the national electrotechnical committees of Greece, Ic

16、eland and Luxembourg. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC members Ref. No. EN 13020

17、0:1993 + A3:1998 EEN130200:1993 BSI 06-1999 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed

18、quality. Ths object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate of Conformity. The components produced under the Syste

19、m are thereby acceptable in all member countries without further testing. This European Standard was prepared by CECCWG 3, Capacitors. The text of the draft based on document CECC30200 Issue 2:1985 was submitted to the formal vote for conversion to a European Standard: together with the voting repor

20、t, circulated as document CECC (Secretariat) 2995 it was approved by CECC as EN 130 200 on 27 January 1992. Thetext of EN 130 200 consists of: CECC 30 200 Issue 2 (with A1 to A6, A8 Erratum), CECC (Sec) 2523/01.90 RV CECC (Sec) 2995/12/91, CECC (Sec) 2874/09.91 RV CECC (Sec) 3088/04.92, The followin

21、g dates were fixed: Foreword to amendment A3 This amendment to the European Standard EN130200 was prepared by CLC/TC CECC/SC 40XA (former WG 3), Capacitors. The text of the draft based on document CECC (Secretariat) 3450 was submitted to the formal vote; together with the voting report, circulated a

22、s document CECC (Secretariat) 3550, it was approved as amendment A2 to EN 130200:1993 on 1994-05-15. The text of the draft based on document CECC (Secretariat) 3541 was submitted to the formal vote; together with the voting report, circulated as document CECC (Secretariat) 3620, it was approved as a

23、mendment A3 to EN 130200:1993 on 1994-10-16. This amendment A3 includes amendment A2. The following dates were fixed: latest date of announcement of the EN at national level (doa) 1991-09-11 latest date of publication of an identical national standard (dop) 1992-03-11 latest date of declaration of n

24、ational standards obsolescence 1992-03-11 latest date of withdrawal of conflicting national standards (dow) 2001-09-11 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-10-01 latest date by which n

25、ational standards conflicting with the amendment have to be withdrawn (dow) 1999-10-01EN130200:1993 BSI 06-1999 3 Contents Page Foreword 2 1 General 5 1.1 Scope 5 1.2 Related documents 5 1.3 Information to be given in a detail specification 5 1.4 Terminology 6 1.5 Marking 6 2 Preferred ratings and c

26、haracteristics 8 2.1 Preferred climatic categories 8 2.2 Preferred values of ratings 8 3 Quality assessment procedures 9 3.1 Primary stage of manufacture 9 3.2 Structurally similar components 9 3.3 Certified test records of released lots 9 3.4 Qualification approval 9 3.5 Quality conformance inspect

27、ion 10 4 Test and measurement procedures 11 4.1 Visual examination and check of dimensions 11 4.2 Electrical tests 11 4.3 Robustness of terminations 12 4.4 Resistance to soldering heat 13 4.5 Solderability 14 4.6 Rapid change of temperature 14 4.7 Vibration 14 4.8 Bump 14 4.9 Shock 15 4.10 Climatic

28、sequence 15 4.11 Damp heat, steady state 16 4.12 Endurance 16 4.13 Surge 16 4.14 Reverse voltage 17 4.15 Characteristics at high and low temperatures 17 4.16 Component solvent resistance 17 4.17 Solvent resistance of the marking 17 4.18 High surge current test 17 Annex A 18 A.1 Test plan for qualifi

29、cation approval assessment level E 18 A.2 Test plan for quality conformance inspection lot-by-lot tests Assessment level E 19 Page A.3 Test plan for quality conformance inspection periodic tests Assessment level E 19 A.4 Test schedule for qualification approval assessment level E 20 Figure 1 13 Tabl

30、e 1 14 Table 2 15 Table 3 174 blankEN130200:1993 BSI 06-1999 5 1 General 1.1 Scope This specification applies to polar and bipolar tantalum electrolytic capacitors with solid or non-solid electrolyte. It comprises capacitors for long-life applications and capacitors for general-purpose applications.

31、 Capacitors for special purpose application may need additonal requirements. Surface mounting styled capacitors are not covered. This specification covers three basic sub-families, namely: The object of this specification is to prescribe preferred ratings and characteristics and to select from the g

32、eneric specification EN130000 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. 1.2 Related documents ISO 3:1973, Preferred numbers Series of preferred numbers. IEC 62:1974, Marking codes for resistors

33、and capacitors. IEC 63:1963, Preferred number series for resistors and capacitors. Amendment 1:1967 Amendment 2:1977. IEC 68, Basic environmental testing procedures. IEC 384-15:1982, Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte. IEC 410:1973, Sampling plans

34、and procedures for inspection by attributes. CECC 00 014:1986, CECC Assessed Process Average Procedure (APA). EN 130 000:1993, Generic specification: Fixed capacitors. 1.3 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specific

35、ation. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk.

36、The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.3.1 Dimensions and outline drawing The detail specification shall give an illustration of the capacit

37、or as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given. All dimensions shall be stated in mm. NOTEThe information may be presented in tabular form. Normally the numeric

38、al values shall be given for the length, the width and height of the body and the wire spacing or for cylindrical types the body diameter, and the length and diameter of the terminations. When necessary, for example when a number of case sizes are covered by a detail specification, the dimensions an

39、d their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards,

40、 this shall be clearly stated in the detail specification. Sub-family 1 : Fixed non-solid electrolyte tantalum capacitors with foil electrode 1A: Plain foil electrode 1B: Etched foil electrode Sub-family 2 : Fixed non-solid electrolyte tantalum capacitors with porous anode Sub-family 3 : Fixed solid

41、 electrolyte tantalum capacitors with porous anode.EN130200:1993 6 BSI 06-1999 1.3.2 Mounting The detail specification shall specify the method of mounting to be applied for the application of the vibration and the bump or shock tests. The design of the capacitor may be such that special mounting fi

42、xtures are required in its use. In this case the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. NOTEIf recommendations for mounting for “normal” use are made, they shall be included in the detail specifica

43、tion under 1.8 “Additional information (not for inspection purposes)”. If they are included, a warning can be given that the full vibration, bump and shock performance may not be available if mounting methods other than those specified in 1.1 of the detail specification are used. 1.3.3 Ratings and c

44、haracteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following: 1.3.3.1 Rated capacitance range See2.2.1. NOTEWhen products approved to the detail specification have different ranges, the following statement should b

45、e added: “The range of capacitance values available in each voltage range is given in the Register of Approvals, CECC00200”. 1.3.3.2 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and application

46、purposes. 1.3.3.3 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability test and the resistance to soldering heat test. 1.3.4 Marking The detail specification shall specify the content of the marking on the capacitor and on

47、the package. Deviations from 1.5 of this sectional specification shall be specifically stated. 1.4 Terminology In addition to the applicable terms and definitions ofEN130000 the following definitions apply: 1.4.1 Capacitance of an electrolytic capacitor The capacitance of an equivalent circuit havin

48、g capacitance and resistance in series measured with alternating current of approximately sinusoidal wave form of the specified frequency. 1.4.2 Performance grade The performance grade shall be noted in the detail specification. 1.4.2.1 Long-life grade capacitors Capacitors intended for applications

49、 where a high degree of stability of characteristics over a long life is essential. 1.4.2.2 General-purpose grade capacitors Capacitors intended for applications where the high performance level of long-life grade capacitors is not required. 1.4.3 Rated voltage (U R ) The maximum d.c. voltage which may be applied continuously to the terminations of a capacitor at the rated temperature. NOTE 1The sum of the d.c. voltage and the peak alternating voltage applied to the capacitor shall not exceed the rated voltage. NOTE 2For short periods