BS EN 13017-2-2001 Solid wood panels - Classification by surface appearance - Hardwood《实心木镶板 根据表面性质分类 硬木》.pdf

《BS EN 13017-2-2001 Solid wood panels - Classification by surface appearance - Hardwood《实心木镶板 根据表面性质分类 硬木》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13017-2-2001 Solid wood panels - Classification by surface appearance - Hardwood《实心木镶板 根据表面性质分类 硬木》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 13017-2:2001 The Eu

2、ropean Standard EN 13017-2:2000 has the status of a British Standard ICS 79.060.99 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Solid wood panels Classification by surface appearance Part 2: HardwoodThis British Standard, having been prepared under the direction of the Sect

3、or Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 January 2001 BSI 01-2001 ISBN 0 580 36581 6 BS EN 13017-2:2001 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard

4、is the official English language version of EN 13017-2:2000. The UK participation in its preparation was entrusted to Technical Committee B/541, Wood based panels, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on th

5、e interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standa

6、rds which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard

7、 does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an

8、inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13017-2 November 2000 ICS 79.060.99 English version Solid wood panels Classificat

9、ion by surface appearance Part 2: Hardwood Bois panneauts Classification selon laspect des faces Partie 2: Bois feuillus Massivholzplatten Klassifizierung nach dem Aussehen der Oberflche Teil 2: Laubholz This European Standard was approved by CEN on 8 September 2000. CEN members are bound to comply

10、with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Cen

11、tre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official v

12、ersions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROP

13、EN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13017-2:2000 EPage 2 EN 13017-2:2000 BSI 01-2001 Contents Page Foreword

14、.3 1 Scope .3 2 Normative references .3 3 Terms and definitions 4 4 General requirements 4 4.1 General requirements for multi-layer solid wood panels .4 4.2 General requirements for single-layer solid wood panels 4 5 Appearance classes .4 5.1 General .4 5.2 Appearance classes of multi-layer solid wo

15、od panels .4 5.3 Appearance classes of single-layer solid wood panels .4 6 Marking 5Page 3 EN 13017-2:2000 BSI 01-2001 Foreword This European Standard was prepared by Technical Committee CEN/TC 112, Wood-based panels, the Secretariat of which is held by DIN. This European Standard shall be given the

16、 status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2001, and conflicting national standards shall be withdrawn at the latest by May 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the fol

17、lowing countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This standard is one of two standards fo

18、r the classification of solid wood panels by surface appearance, the other is: EN 13017-1, Solid wood panels Classification by surface appearance Part 1: Softwood. 1 Scope This European standard specifies general requirements and appearance classes for both single layer and multi-layer solid wood pa

19、nels, the latter with a minimum thickness of the outer layers of 3,5 mm, manufactured from hardwood species. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places i

20、n the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred

21、 to applies (including amendments). EN 844-1, Round and sawn timber Terminology Part 1: General terms common to round timber and sawn timber. EN 844-3, Round and sawn timber Terminology Part 3: General terms relating to sawn timber. EN 844-4, Round and sawn timber Terminology Part 4: Terms relating

22、to moisture content. EN 844-6, Round and sawn timber Terminology Part 6: Terms relating to dimensions of sawn timber. EN 844-7, Round and sawn timber Terminology Part 7: Terms relating to anatomical structure of timber. EN 844-9, Round and sawn timber Terminology Part 9: Terms relating to features o

23、f sawn timber. EN 844-10, Round and sawn timber Terminology Part 10: Terms relating to stain and fungal attack. EN 844-11, Round and sawn timber Terminology Part 11: Terms relating to degrade by insects. EN 1310, Round and sawn timber Method of measurement of features. EN 1311, Round and sawn timber

24、 Method of measurement of biological degrade. prEN 12775:2000, Solid wood panels Classification and terminology. prEN 13353:1998, Solid wood panels Requirements.Page 4 EN 13017-2:2000 BSI 01-2001 3 Terms and definitions For the purposes of this standard the terms and definitions given in prEN 12775:

25、2000 apply, together with some common terms referring to timber which are given in those parts of EN 844 listed in Clause 2. 4 General requirements 4.1 General requirements for multi-layer solid wood panels All types of panels shall have a symmetrical construction throughout their thickness. Joints

26、in the outer layer shall be glued; open glue lines, with the exception in Grades B and C (see Table 1), are not permitted. Unglued joints are permitted in the inner layers. Butt joints and finger joints in the individual pieces of the inner layers are also permitted. The width of lamellas in the out

27、er layers should be at least 75 mm. All layers and lamellas of a panel shall be made of the same wood species. The surfaces of the panel shall be fine sanded. Some surface blemishes are only permitted in Grade C. 4.2 General requirements for single-layer solid wood panels All joints shall be properl

28、y glued; open joints are not permitted. Mixing of wood species within one panel is not permitted. The surfaces of the panel shall be planed or sanded. Cuttermarks are not permitted. Some sanding blemishes in the surface are only permitted in Grade C. Panels with pieces of timber cut in length may ha

29、ve pieces finger jointed as well as butt jointed or have any other type of end joint. 5 Appearance classes 5.1 General Classification for appearance classes shall be in accordance with the requirements given in Table 1. The measurement of features shall be made according to EN 1310. For knots the ge

30、neral method according to EN 1310:1997, 4.1.1 shall be used. 5.2 Appearance classes of multi-layer solid wood panels Assessment of appearance classes shall be made for both face and back of the panel. In marking and specification, the symbols of the classes of both face and back shall be given separ

31、ated by a slash as face class/back class (e.g. A/C). 5.3 Appearance classes of single-layer solid wood panels Assessment of appearance classes shall be made on the better surface on the panel. Only the appearance class of the better surface shall be given in the specification of the panel.Page 5 EN

32、13017-2:2000 BSI 01-2001 Table 1 Appearance classes for multi-layer and single-layer solid wood panels Appearance class Features ABC Glueing Outer layer perfectly glued, with closed joints on edges and faces Outer layer perfectly glued on faces, no requirements on edge glueing Appearance and colour

33、Composed appearance, balanced in colour Pronounced as well as rustic appearance permitted No requirements Texture Texture, typical for the species permitted, uniform texture required Coarse texture permitted No requirements Brown, wet, irregular heart Not permitted Not permitted a) Permitted Rays Pe

34、rmitted Sapwood Permitted b) Permitted c) Permitted Fiddle back grain Permitted Dormant shoots Permitted Pin knots Permitted Sound intergrown knots Permitted up to a diameter of 10 mm, single up to diameter of 25 mm Up to a diameter of 30 mm Permitted Loose knots, patches Not permitted Loose knots a

35、nd patches or plugs in rows not permitted; fine patch-work or plugs up to a diameter of 30 mm permitted Permitted, with or without patches Fissures Not permitted Single shakes up to 2 mm 50 mm permitted; shakes near the edges permitted up to 1 mm 100 mm Permitted Ingrown bark Not permitted Permitted

36、 Insect attack, small worm holes Not permitted Discolouration, fungal attack d) Not permitted Slight discolouration permitted; rot not permitted Rot not permitted Open joints Not permitted Near the edges permitted up to 1 mm 200 mm Permitted Thickness of glue line max. 0,2 mm max. 0,2 mm No requirem

37、ent Length of pieces of panel type SC min. 150 mm a)Brown heart in class B permitted with ash and red heart with steamed or unsteamed beech. b)Sapwood not permitted in class A with oak, cherry, elm, sweet chestnut or false acacia. c)Sapwood not permitted in class B with oak or sweet chestnut. d)Can

38、be measured according to EN 1311. 6 Marking Marking shall be made in accordance with the panel type suitable for certain climatic conditions in service. For full marking of panels see prEN 13353:1998.BS EN 13017-2:2001 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | |

39、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for

40、 preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or e

41、ditions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the

42、 inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications shou

43、ld be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standar

44、ds, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on al

45、l its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Member

46、ship Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies

47、. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free us

48、e, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.