BS EN 12488-2016 Glass in building Glazing recommendations Assembly principles for vertical and sloping glazing《建筑用玻璃 玻璃装配建议 垂直和倾斜玻璃装配原则》.pdf

《BS EN 12488-2016 Glass in building Glazing recommendations Assembly principles for vertical and sloping glazing《建筑用玻璃 玻璃装配建议 垂直和倾斜玻璃装配原则》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12488-2016 Glass in building Glazing recommendations Assembly principles for vertical and sloping glazing《建筑用玻璃 玻璃装配建议 垂直和倾斜玻璃装配原则》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 12488:2016Glass in building Glazingrecommendations Assemblyprinciples for vertical andsloping glazingBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12488:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12488:201

2、6.The UK participation in its preparation was entrusted to TechnicalCommittee B/520/4, Properties and glazing methods.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contrac

3、t. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 83392 2ICS 81.040.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authorit

4、y of theStandards Policy and Strategy Committee on 31 July 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 12488:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12488 June 2016 ICS 81.040.20 English Version Glass in building - Glazing recommendations - A

5、ssembly principles for vertical and sloping glazing Verre dans la construction - Recommandations pour la mise en oeuvre - Principes de pose pour vitrage vertical et inclin Glas im Bauwesen - Empfehlungen fr die Verglasung -Verglasungsgrundlagen fr vertikale und abfallende Verglasung This European St

6、andard was approved by CEN on 8 April 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning

7、such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its

8、own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany

9、, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NO

10、RMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12488:2016 EBS EN 12488:2016EN 12488:2016 (E) 2 Contents Page European foreword . 4 Introduction 5 1 Scope

11、6 2 Normative references 6 3 Terms and definitions . 7 4 Basic requirements . 12 4.1 General . 12 4.2 Support of glazing 12 4.3 Mechanical stability 12 4.4 Durability 13 4.4.1 Ultraviolet attack on sensitive components . 13 4.4.2 Chemical and atmospheric attack on sensitive components . 13 4.4.3 Wea

12、ther tightness 13 4.4.4 Additional considerations for sloping glazing . 13 4.5 Special requirements 13 5 Requirements for the components 14 5.1 Frame selection, materials and finishes 14 5.1.1 Design of the frame 14 5.1.2 Selection 14 5.1.3 Frame materials . 15 5.2 Sealants 15 5.3 Preformed strip ma

13、terials 16 5.4 Putty 16 5.5 Glazing blocks 17 5.5.1 General . 17 5.5.2 Setting blocks . 18 5.5.3 Location block . 19 5.5.4 Distance pieces 20 5.5.5 Temporary blocks 21 Annex A (informative) Recommendations for drainage and ventilation 22 A.1 General . 22 A.2 Drainage and ventilation per module: . 22

14、 A.3 Cascading drainage and ventilation 24 Annex B (informative) Aspects for determining the rebate dimensions 26 B.1 General . 26 B.2 Insulating glass unit 27 Annex C (informative) Positioning of glazing blocks as a function of frame type 28 C.1 General . 28 C.2 Position of the glazing blocks for v

15、ertical windows and doors . 29 C.3 Position of the glazing blocks for sloped glazings 35 Annex D (informative) Additional considerations for sloped glazing . 37 BS EN 12488:2016EN 12488:2016 (E) 3 D.1 Water entrapment 37 D.2 Snow and ice entrapment 37 Bibliography . 39 BS EN 12488:2016EN 12488:2016

16、(E) 4 European foreword This document (EN 12488:2016) has been prepared by Technical Committee CEN/TC 129 “Glass in building”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsemen

17、t, at the latest by December 2016, and conflicting national standards shall be withdrawn at the latest by December 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identify

18、ing any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implemen

19、t this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Sl

20、ovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12488:2016EN 12488:2016 (E) 5 Introduction This European Standard deals with the glazing system i.e. the glazing, the glazing blocks, the sealants, the gaskets and the components used to assemble the glazing into a fr

21、ame, as well as the rebate. It gives the basic principles to avoid damages due to the construction. The observance of these recommendations will ensure a reasonable working life of the glazing. Additional requirements and precisions are to be found in the national regulations and/or national codes o

22、f practice, in order to deal with regional particularities due to climate, professional habits, availability of materials, etc. Special requirements can also be specified by manufacturers of components of the glazing system, including glazing. Mechanical, thermal, chemical and moisture conditions ar

23、e essential to preserve the functionality and the operability of the glazing in the long term. Information with regards to the durability of a glass product is given in the applicable harmonized European Standard (hEN). BS EN 12488:2016EN 12488:2016 (E) 6 1 Scope This European Standard defines princ

24、iples of glazing as well as recommendations on the selection of components, e.g. frame sections, beads, drainage holes, etc., for fitting glazing into frames of any material. This European Standard applies to all basic types of edge supported vertical and sloping glazing systems, in all types of fix

25、ed or opening frames used in buildings. This European standard specifies also the functions, requirements and installation of glazing blocks within a frame during its manufacturing, transportation, installation and operational life. The standard applies to glazing blocks used for all types of flat o

26、r curved glass, as well as to derived processed types of glass. For certain glass products, e.g. fire resistant glazing, security glass, other or additional requirements, rules or recommendations may apply. The standard is applicable to European climate conditions. This European Standard does not ap

27、ply to the following: glass blocks and glass pavers (EN 1051-1); channel-shaped glass (EN 572-7); structural sealant glazing (see EN 13022-1 and EN 13022-2 and ETAG 002); adhesively bonded glazing in window; point fixed glazing; greenhouses (see EN 13031-1). As this standard gives basic assembly pri

28、nciples only, national requirements, rules or recommendations may also apply. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated

29、references, the latest edition of the referenced document (including any amendments) applies. EN 1279-1, Glass in Building Insulating glass units Part 1: Generalities, dimensional tolerances and rules for the system description EN 12365-1, Building hardware Gasket and weatherstripping for doors, win

30、dows, shutters and curtain walling Part 1: Performance requirements and classification EN 13241-1, Industrial, commercial and garage doors and gates Product standard Part 1: Products without fire resistance or smoke control characteristics EN 13830, Curtain walling Product standard EN 14351-1, Windo

31、ws and doors Product standard, performance characteristics Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics BS EN 12488:2016EN 12488:2016 (E) 7 prEN 14351-2, Windows and doors Product standard, performance characteristics Part 2: Intern

32、al pedestrian doorsets without resistance to fire and/or smoke leakage characteristics EN 16034, Pedestrian doorsets, industrial, commercial, garage doors and openable windows Product standard, performance characteristics Fire resisting and/or smoke control characteristics EN 15651-2, Sealants for n

33、on-structural use in joints in buildings and pedestrian walkways Part 2: Sealants for glazing EN ISO 868, Plastics and ebonite Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868) 3 Terms and definitions For the purposes of this document, the following terms and d

34、efinitions apply. NOTE Whenever the word “frame” is used, it refers also to the sash and casement, according to EN 12519. 3.1 glazing glass product that is monolithic, laminated, and/or insulating glass unit Note 1 to entry: In French called “vitrage” and in German called “Glasaufbau”. 3.2 vertical

35、glazing glazing which is not more than 15 from vertical, either inwards or outwards 3.3 sloping glazing glazing which is sloping between 15 and 85 from the vertical Note 1 to entry: Glazing between 85 and 90 may be subjected to water ponding that should be prevented by proper design 3.4 glazing syst

36、em materials and the conditions under which the glazing is installed into a frame 3.5 drained and pressure equalized glazing system glazing system that enable any water and water vapour which has entered the rebate to be effectively removed Note 1 to entry: Openings for ventilation and drainage in t

37、he frame are designed to achieve partial water vapour pressure equalization and evacuation of water from the glazing rebate to the outside of the building. Note 2 to entry: Recommendations for drainage and ventilation are given in informative Annex A. 3.6 fully bedded glazing system sealant that com

38、pletely covers the perimeter of the glazing Note 1 to entry: Fully bedded system is not recommended for insulating glass units and laminated glass. BS EN 12488:2016EN 12488:2016 (E) 8 3.7 glazing rebate part of a frame or surround into which the glazing is glazed Note 1 to entry: See Figure 1. 3.8 g

39、lazing rebate platform face of the glazing rebate which forms an angle with the upstand Note 1 to entry: See Figure 1. Note 2 to entry: This can be opened or closed. 3.9 glazing rebate upstand fixed face of the glazing rebate parallel to the face of the glazing Note 1 to entry: See Figure 1. 3.10 gl

40、azing bead component holding the glazing in place in the glazing rebate Note 1 to entry: See Figure 1. Note 2 to entry: For vertical windows, the bead may be fixed either internally or externally. For sloping glazing, the bead is fixed externally. 3.11 drainage channel channel in the rebate platform

41、 aiming at collecting possible water coming from infiltration and/or condensation, in order to evacuate it to the exterior of the frame, and to connect rebate spaces to equalise pressure around the glazing Note 1 to entry: See Figure 1. 3.12 drainage opening opening that evacuate the possible water

42、collected in the drainage channel to the outside of the frame Note 1 to entry: See Figure 1. 3.13 glass retention area r height of the perimeter of the glass that transmits loads to the frame Note 1 to entry: See Figure 2 and Annex B. BS EN 12488:2016EN 12488:2016 (E) 9 3.14 free intersection f non

43、load-bearing part of the glass around the perimeter Note 1 to entry: See Figure 2 and Annex B. 3.15 mechanical edge cover m sum of the glass retention area (r) and the free intersection (f) Note 1 to entry: See Figure 2 and Annex B. 3.16 edge clearance Jp distance, which may be variable, between the

44、 edge of the glazing and the glazing rebate platform Note 1 to entry: See Figure 2 and Annex B. 3.17 rebate depth t sum of the mechanical edge cover (m) and the edge clearance (Jp) Note 1 to entry: See Figure 2 and Annex B. Note 2 to entry: In German: Glasfalzhhe. 3.18 face clearance d distance betw

45、een either glazing and the rebate upstand or glazing and the bead Note 1 to entry: See Figure 2 and Annex B. 3.19 glazing block piece of suitable material placed between the glazing and the frame preventing direct contact between the two of them Note 1 to entry: See Figure 3 and Annex C. Note 2 to e

46、ntry: Glazing blocks may not take over any loads from the construction. Note 3 to entry: Glazing blocks include setting blocks, location blocks and distance pieces. 3.20 setting block glazing block transferring the load of the glazing via the hardware and/or frame to the structure of the building No

47、te 1 to entry: See Figure 3 and Annex C. BS EN 12488:2016EN 12488:2016 (E) 10 3.21 location block glazing block holding the correct position of the glazing in the frame Note 1 to entry: See Figure 3 and Annex C. 3.22 distance piece glazing block used to transmit the loads perpendicular to the plane

48、of glazing Note 1 to entry: See Figure 3 and Annex C. Note 2 to entry: This function can also be ensured by a strip or a gasket. 3.23 compensation block block that create a flat platform for the correct positioning of setting block or location block in certain frame profiles Note 1 to entry: See Fig

49、ure 3. Note 2 to entry: Compensation block is generally used with aluminium or plastic profiles. 3.24 temporary block additional glazing block used to ensure the correct positioning of the glazing when glazed frames are transported to a work site, and that may be removed before installation of the glazed frame into the building Vertical glazing, open rebate Vertical glazing, closed rebate Sloping glazing Key 1 glazing rebate platform 4 drainage channel 2 glazing rebate upstand 5 drainage opening 3 glazing bead Figure 1 Def