BS EN 12482-1-1998 Aluminium and aluminium alloys - Reroll stock for general applications - Specifications for hot rolled reroll stock《铝和铝合金 通用重轧胚料 热轧重轧胚料规范 》.pdf

《BS EN 12482-1-1998 Aluminium and aluminium alloys - Reroll stock for general applications - Specifications for hot rolled reroll stock《铝和铝合金 通用重轧胚料 热轧重轧胚料规范 》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12482-1-1998 Aluminium and aluminium alloys - Reroll stock for general applications - Specifications for hot rolled reroll stock《铝和铝合金 通用重轧胚料 热轧重轧胚料规范 》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12482-1:1998 The Eu

2、ropean Standard EN 12482-1:1998 has the status of a British Standard ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Aluminium and aluminium alloys Reroll stock for general applications Part 1: Specifications for hot rolled reroll stockBS EN 12482-1:1998 This Bri

3、tish Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 December 1998 BSI 1998 ISBN 0 580 30338 1 Amendments issued since publication Amd. No. Date Text affected National for

4、eword This British Standard is the English language version of EN 12482-1:1998. The UK participation in its preparation was entrusted by Technical Committee NFE/35, Light metals and their alloys, to Subcommittee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: aid e

5、nquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organization

6、s represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards C

7、orrespondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard doe

8、s not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Cent

9、ral Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12482-1:1998 E EUROPEAN STANDARD EN 12482-1 NORME EUROPE ENNE EUROPA ISCHE NORM July 1998 ICS 77.150.10 Descriptors: aluminiu

10、m, aluminium alloys, hot rolled products, reroll stock, definitions, specifications, delivery, orders, sales documents, dimensions, dimensional tolerances, tests, acceptance testing, marking, packing English version Aluminium and aluminium alloys Reroll stock for general applications Part 1: Specifi

11、cations for hot rolled reroll stock Aluminium et alliages daluminium Ebauches de relaminage pour applications ge ne rales Partie 1: Spe cifications pour e bauches obtenues par laminage a chaud Aluminium und Aluminiumlegierungen Vorwalzband fu r allgemeine Anwendungen Teil 1: Spezifikationen fu r war

12、mgewalztes Vorwalzband This European Standard was approved by CEN on 1 July 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

13、bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibili

14、ty of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherland

15、s, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 12482-1:1998 BSI 1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 132, Aluminium and aluminium alloys, the Secretariat of which is held by AFNOR. This European Standard shall be given the

16、 status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1999, and conflicting national standards shall be withdrawn at the latest by January 1999. This European Standard has been prepared under a mandate given to CEN by the European Comm

17、ission and the European Free Trade Association, and supports essential requirements of EU Directive(s). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic,

18、Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This standard is part of a series of two standards. The other standard deals with: EN 12482-2, Aluminium and aluminium alloys Reroll stock

19、 for general applications Part 2: Specifications for cold rolled reroll stock. Contents Page Foreword 2 Introduction 3 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Technical conditions for inspection and delivery 3 5 Tolerances on dimensions 4 6 Inspection documents 5 7 Marking 5 8 Packing 5

20、 9 Arbitration tests 5Page 3 EN 12482-1:1998 BSI 1998 Introduction When hot or cold rolled strip in aluminium and aluminium alloy is to be rolled to thinner gauges in order to obtain cold rolled products such as sheets, strips, finstock and foil, this intermediate product is then called reroll stock

21、. As the properties of the final products depend on the properties of the reroll stock and the further process, it is therefore not practicable to specify in detail minimum requirements for all properties of reroll stock. This standard therefore gives only guidelines to the specifications which have

22、 to be established carefully between producer and purchaser prior to ordering. 1 Scope This part of EN 12482 specifies the particular requirements for wrought aluminium and aluminium alloys in the form of hot rolled strip. The thickness range covered is from 2,0 mm to 12 mm. It does not apply to hot

23、 rolled strip which is not rerolled, such as strip for general engineering or special applications. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text

24、 and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies

25、. EN 485-1, Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and delivery. EN 515, Aluminium and aluminium alloys Wrought products Temper designations. EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3:

26、Chemical composition. EN 12258-1, Aluminium and aluminium alloys Terms and definitions Part 1: General terms. 3 Definitions For the purposes of this European Standard, the definitions of aluminium and aluminium alloy according to EN 12258-1, the definitions of strip, hot rolled strip, sample, test p

27、iece and test according to EN 485-1, and the following apply. 3.1 reroll stock rolled strip destined to be rolled to thinner gauges in order to obtain cold rolled products such as sheets, strips, finstock and foil 3.2 hot rolled reroll stock reroll stock whose final thickness is obtained by hot roll

28、ing 4 Technical conditions for inspection and delivery 4.1 Orders or tenders The order or tender shall define the product required and shall contain at least the following information: a) the form and type of product: 1) the designation of the aluminium or aluminium alloy in accordance with EN 573-3

29、; 2) the application intended by the purchaser: the form, final thickness and temper to which the product is transformed at the purchasers works; any indication on intended surface treatments; b) the temper of the product for delivery in accordance with EN 515; c) whether mechanical properties are t

30、o be specified; d) the number of this European Standard or a specification number, or, where none exists, the properties agreed between purchaser and producer; e) the dimensions and shape of the product: thickness; width; net mass of the coil; internal and external diameters of the coil; f) the quan

31、tity: number of coils; minimum and maximum mass of coils; tolerance on quantity if required; g) any requirements for inspection documents; h) any special requirements for packing: mass per coil; design of pallet; i) any special requirements agreed between producer and purchaser: marking of products;

32、 additional property requirements.Page 4 EN 12482-1:1998 BSI 1998 Table 1 Tolerances on thickness Dimensions in millimetres Specified thickness Tolerance on thickness for specified width Over Up to and including Over 1 250 up to and including 1 600 Over 1 600 up to and including 2 000 Over 2 000 up

33、to and including 2 500 2,0 1) 4 0,30 0,35 0,40 45 0,35 0,40 0,45 56 0,40 0,45 0,50 68 0,45 0,50 0,55 1) Including thickness of 2,0 mm. 4.2 Requirements 4.2.1 Production and manufacturing process Unless otherwise stated in the order, the production and manufacturing processes shall be left to the dis

34、cretion of the producer. Unless it is explicitly stated in the order no obligation shall be placed on the producer to use the same processes for subsequent and similar orders. 4.2.2 Quality control The producer shall be responsible for the performance of all inspection and tests required by the rele

35、vant European Standard and/or the particular specification, prior to shipment of the product. If the purchaser wishes to inspect the product at the producers works, he shall notify the producer at the time of placing the order. 4.2.3 Freedom from defects The product shall be free from defects prejud

36、icial to its suitable and proper use. It shall have a smooth and clean rolling surface. The surface condition shall be agreed between producer and purchaser. 4.2.4 Chemical composition The chemical composition shall comply with the requirements as specified in EN 573-3. If the purchaser requires con

37、tent limits for elements not specified in the above standard, these limits shall be stated on the order, after agreement between producer and purchaser. 4.2.5 Mechanical properties If mechanical properties are required, they shall be agreed between producer and purchaser and stated on the order. 4.2

38、.6 Tolerances on dimensions The tolerances on dimensions shall be in conformity with those specified in clause 5 or agreed between producer and purchaser and stated on the order. 4.2.7 Other properties Additional property requirements, such as surface aspect, edge trimming, etc., shall be agreed bet

39、ween producer and purchaser and stated on the order. 4.3 Test procedures 4.3.1 Chemical composition Chemical composition shall be tested as specified in EN 485-1. 4.3.2 Tensile test Selection and preparation of samples and test pieces shall be in conformity with EN 485-1. 4.3.3 Retests Retests shall

40、 be carried out in conformance with EN 485-1. 5 Tolerances on dimensions 5.1 Thickness Tolerances on thickness are specified in Table 1. Tolerances on thickness for nominal thickness between 8 mm and 12 mm shall be agreed between producer and purchaser. 5.2 Width 5.2.1 Strip without trimmed edges To

41、lerances on width for strip without trimmed edges shall be agreed between producer and purchaser and stated on the order. 5.2.2 Strip with trimmed edges For specified width over 600 mm up to 2 500 mm, the tolerance on width is mm. 0 +8Page 5 EN 12482-1:1998 BSI 1998 6 Inspection documents Inspection

42、 documents shall be in conformity with those specified in EN 485-1. 7 Marking Unless otherwise agreed at the time of ordering, the following marking requirements shall apply: a) name or mark of the producer; b) alloy and temper designation; c) order number; d) ordered dimensions; e) production batch

43、 number and mass. Each of these items shall be given on a label, which is to be attached to every coil or pack. 8 Packing The packing requirements shall be agreed between producer and purchaser. 9 Arbitration tests In cases of dispute concerning conformity with the requirements of this European Stan

44、dard or specification cited on the order, before rejecting the products, testing and examination shall be carried out by an arbitrator chosen by mutual agreement between producer and purchaser. The arbitrators decision is final.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | |

45、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body respon

46、sible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendm

47、ents or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be fou

48、nd on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publicat

49、ions should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI