BS EN 12350-2-2009 Testing fresh concrete - Slump-test《新拌混凝土试验 坍落试验》.pdf

《BS EN 12350-2-2009 Testing fresh concrete - Slump-test《新拌混凝土试验 坍落试验》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12350-2-2009 Testing fresh concrete - Slump-test《新拌混凝土试验 坍落试验》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN12350-2:2009ICS 91.100.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTesting fresh concretePart 2: Slump-testThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2009 BSI 2009ISBN 978 0 580 58

2、789 4Amendments/corrigenda issued since publicationDate CommentsBS EN 12350-2:2009National forewordThis British Standard is the UK implementation of EN 12350-2:2009. It supersedes BS EN 12350-2:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/517/

3、1, Concrete production and testing.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. Compliance with a British Sta

4、ndard cannot confer immunityfrom legal obligations.BS EN 12350-2:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 12350-2March 2009ICS 91.100.30 Supersedes EN 12350-2:1999 English VersionTesting fresh concrete - Part 2: Slump-testEssais pour bton frais - Partie 2: Essai daffaissement Prfung von

5、 Frischbeton - Teil 2: SetzmaThis European Standard was approved by CEN on 20 January 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date li

6、sts and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the respo

7、nsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Icela

8、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marni

9、x 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12350-2:2009: EBS EN 12350-2:2009EN 12350-2:2009 (E) 2 Contents Page Foreword 31 Scope 52 Normative references 53 Principle 54 Apparatus .55 Test sample 66 Pr

10、ocedure .67 Test result .78 Test report 89 Precision .8BS EN 12350-2:2009EN 12350-2:2009 (E) 3 Foreword This document (EN 12350-2:2009) has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. This European Standard shall be given

11、the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009. Attention is drawn to the possibility that some of the elements of this document ma

12、y be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12350-2:1999. This standard is one of a series concerned with testing concrete. This series EN 12350 includes the following parts: Part 1: Sa

13、mpling; Part 2: Slump-test; Part 3: Vebe test; Part 4: Degree of compactability; Part 5: Flow table test; Part 6: Density; Part 7: Air content - Pressure methods; Part 8: Self-compacting concrete - Slump-flow test (in preparation); Part 9: Self-compacting concrete - V-funnel test (in preparation); P

14、art 10: Self-compacting concrete - L-box test (in preparation); Part 11: Self-compacting concrete - Sieve segregation test (in preparation); Part 12: Self-compacting concrete - J-ring test (in preparation). CAUTION When cement is mixed with water, alkali is released. Take precautions to avoid dry ce

15、ment entering the eyes, mouth and nose whilst mixing concrete. Prevent skin contact with wet cement or concrete by wearing suitable protective clothing. If cement or concrete enters the eye, immediately wash it out thoroughly with clean water and seek medical treatment without delay. Wash wet concre

16、te off the skin immediately. BS EN 12350-2:2009EN 12350-2:2009 (E) 4 The following amendments have been made to the 1999-10 edition of this standard: editorial revision; time allowed for raising the mould changed from between 5 s and 10 s to between 2 s and 5 s. According to the CEN/CENELEC Internal

17、 Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

18、 Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 12350-2:2009EN 12350-2:2009 (E) 5 1 Scope This European standard specifies a method for determining the consistence of fresh concrete by the slump test. The slump test is sen

19、sitive to changes in the consistence of concrete, which correspond to slumps between 10 mm and 210 mm. Beyond these extremes the measurement of slump can be unsuitable and other methods of determining the consistency should be considered. If the slump continues to change over a period of 1 min after

20、 de-moulding, the slump test is not suitable as a measure of consistence. The test is not suitable when the maximum size of aggregate in the concrete is greater than 40 mm. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated ref

21、erences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12350-1 Testing fresh concrete Part 1: Sampling 3 Principle The fresh concrete is compacted into a mould in the shape of a frustum of a cone. When the

22、 cone is withdrawn upwards, the distance the concrete has slumped provides a measure of the consistency of the concrete. 4 Apparatus 4.1 Mould to form the test specimen, made of metal not readily attacked by cement paste and not thinner than 1,5 mm. The interior of the mould shall be smooth and free

23、 from projections, such as protruding rivets and shall be free from dents. The mould shall be in the form of a hollow frustum of a cone having the following internal dimensions: diameter of base: (200 2) mm; diameter of top: (100 2) mm; height: (300 2) mm. The base and the top of the mould shall be

24、open and parallel to each other and at right angles to the axis. The mould shall be provided with two handles near the top and fixing clamps or foot pieces near the bottom to hold it steady. A mould which can be clamped to the base is acceptable provided the clamping arrangement can be fully release

25、d without movement of the mould or interference with the slumping concrete. BS EN 12350-2:2009EN 12350-2:2009 (E) 6 4.2 Compacting rod, of circular cross-section, straight, made of steel, having a diameter of (16 1) mm and length of (600 5) mm, and with rounded ends. 4.3 Funnel (optional), made of n

26、on-absorbent material not readily attacked by cement paste and having a collar to enable the funnel to be located on the mould specified in 4.1. 4.4 Rule, graduated from 0 mm to 300 mm, at intervals not exceeding 5 mm, the zero mark being at the extreme end of the rule. 4.5 Base plate/surface, non-a

27、bsorbent, rigid, flat, plate or other surface on which to place the mould. 4.6 Remixing container, flat tray of rigid construction and made from a non-absorbent material not readily attacked by cement paste. It shall be of appropriate dimensions such that the concrete can be thoroughly re-mixed, usi

28、ng the square-mouthed shovel or scoop. 4.7 Shovel, with square mouth NOTE The square mouth is required to ensure proper mixing of material on the remixing container. 4.8 Moist cloth. 4.9 Scoop, approximately 100 mm in width. 4.10 Timer, or clock capable of measuring to 1 s. 5 Test sample The sample

29、of the concrete shall be obtained in accordance with EN 12350-1. The sample shall be re-mixed using the remixing container and the square mouthed shovel before carrying out the test. NOTE Alternative sampling procedures may be given in national standards or provisions in the place of use of the conc

30、rete. 6 Procedure Dampen the mould and base plate and place the mould on the horizontal base plate/surface. During filling of the mould hold it firmly against the base plate/surface by clamping in place, or by standing on the two foot pieces. Fill the mould in three layers, each approximately one-th

31、ird of the height of the mould when compacted. Compact each layer with 25 strokes of the tamping rod. Uniformly distribute the strokes over the cross-section of each layer. For the bottom layer this will necessitate inclining the rod slightly and positioning approximately half the strokes spirally t

32、oward the centre. Compact the first layer throughout its depth, taking care not striking the base. Compact the second layer and the top layer each throughout its depth, so that the strokes just penetrate into the immediately underlying layer. In filling and compacting the top layer, heap the concret

33、e above the mould before tamping is started. If the tamping operation of the top layer results in subsidence of the concrete below the top edge of the mould, add more concrete to keep an excess above the top of the mould at all times. After the top layer has been compacted, strike off the surface of

34、 the concrete by means of a sawing and rolling motion of the compacting rod. BS EN 12350-2:2009EN 12350-2:2009 (E) 7 Remove spilled concrete from the base plate/surface. Remove the mould from the concrete by raising it carefully in a vertical direction. Perform the operation of raising the mould in

35、2 s to 5 s, by a steady upward lift, with no lateral or torsional motion being imparted to the concrete. Carry out the entire operation from the start of the filling to the removal of the mould without interruption and complete it within 150 s. Immediately after removal of the mould, measure and rec

36、ord the slump h by determining the difference between the height of the mould and that of the highest point of the slumped test specimen as shown in Figure 1. NOTE The consistency of a concrete mix changes with time, due to hydration of the cement and, possibly, loss of moisture. Tests on different

37、samples should, therefore, be carried out at a constant time interval after mixing, if strictly comparable results are to be obtained. 7 Test result The test is only valid if it yields a true slump, this being a slump in which the concrete remains substantially intact and symmetrical as shown in Fig

38、ure 2(a). If the specimen shears, as shown in Figure 2(b), another sample shall be taken and the procedure repeated. If two consecutive tests show a portion of the concrete shearing off from the mass of the test specimen, the concrete lacks the necessary plasticity and cohesiveness for the slump tes

39、t to be suitable. Report the true slump h, as shown in Figure 1, to the nearest 10 mm. Figure 1 Slump measurement a) True slump b)Shear slump Figure 2 Forms of slump BS EN 12350-2:2009EN 12350-2:2009 (E) 8 8 Test report The report shall include: a) identification of the test sample; b) location of p

40、erformance of test; c) date of test; d) type of slump true/shear; e) measured true slump, to nearest 10 mm; f) any deviation from standard test method; g) declaration by the person technically responsible for the test that it was carried out in accordance with this document, except as noted in item

41、f). The report may include: h) temperature of the concrete sample at time of test; i) time of test. 9 Precision Precision data are given in Table 1. These apply to slump measurements made on concrete from the same sample and when each test result is obtained from a single slump determination. The va

42、lues which apply when each test result is obtained as the average of duplicate determinations are given in Table 2. Table 1 Precision data for slump measurements (single determination) Range (mm) Repeatability conditions Reproducibility conditions Sr(mm) r (mm) SR(mm) R (mm) 50 to 80 5,8 16 9,0 25 T

43、able 2 Precision data for slump measurements (duplicate determinations) Range (mm) Repeatability conditions Reproducibility conditions Sr(mm) r (mm) SR(mm) R (mm) 50 to 80 4,1 11 8,0 22 NOTE 1 The precision data was determined as part of an experiment in the UK in 1987 in which precision data was ob

44、tained for several of the tests then described in BS 1881. The experiment involved 16 operators. The concretes were made using an ordinary Portland cement, Thames Valley sand, and Thames Valley 10 mm and 20 mm coarse aggregates. NOTE 2 The difference between two test results from the same sample by

45、one operator using the same apparatus within the shortest feasible time interval will exceed the repeatability value r on average not more than once in 20 cases in the normal and correct operation of the method. BS EN 12350-2:2009EN 12350-2:2009 (E) 9 NOTE 3 Test results on the same sample obtained

46、within the shortest feasible time interval by two operators each using their own apparatus will differ by the reproducibility value R on average not more than once in 20 cases in the normal and correct operation of the method. NOTE 4 For further information on precision, and for definitions of the s

47、tatistical terms used in connection with precision, see ISO 5725. BS EN12350-2:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards.

48、It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of B

49、SI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standard