BS EN 10277-1-2008 en 6009 Bright steel products - Technical delivery conditions - General《光亮钢产品 交货技术条件 总则》.pdf

《BS EN 10277-1-2008 en 6009 Bright steel products - Technical delivery conditions - General《光亮钢产品 交货技术条件 总则》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10277-1-2008 en 6009 Bright steel products - Technical delivery conditions - General《光亮钢产品 交货技术条件 总则》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 10277-1:2008Bright steel products Technical delivery conditions Part 1: GeneralICS 77.140.60g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43

2、g55g3g47g36g58BS EN 10277-1:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 52920 7National forewordThis British Standard is the UK implementation of EN 10277-1:2008. It supersedes BS EN 10277-1:1999 w

3、hich is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/31, Wrought steels.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a cont

4、ract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10277-1March 2008ICS 77.140.60 Supersedes EN 10277-1:1

5、999 English VersionBright steel products - Technical delivery conditions - Part 1:GeneralProduits en acier transforms froid - Conditionstechniques de livraison - Partie 1: GnralitsBlankstahlerzeugnisse - Technische Lieferbedingungen -Teil 1: AllgemeinesThis European Standard was approved by CEN on 4

6、 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be

7、obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Mana

8、gement Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

9、y, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and

10、by any means reservedworldwide for CEN national Members.Ref. No. EN 10277-1:2008: EEN 10277-1:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Classification and designation.6 4.1 Classification6 4.2 Designation 6 5 Information to be supplied by the

11、purchaser .6 5.1 Mandatory information6 5.2 Options .7 6 Manufacturing process .7 6.1 Steel making process7 6.2 Manufacture of the product 8 6.3 Delivery conditions8 7 Requirements.8 7.1 Chemical composition 8 7.2 Mechanical properties.8 7.3 Hardenability 8 7.4 Grain size9 7.5 Non-metallic inclusion

12、s 9 7.6 Decarburization9 7.7 Surface condition.9 7.8 Internal soundness10 7.9 Dimensions, shape and tolerances10 8 Inspection and testing.10 8.1 Types and contents of inspection documents .10 8.2 Specific inspection 11 9 Marking .11 Annex A (normative) Ruling section for mechanical properties 13 Ann

13、ex B (normative) Options .16 Bibliography 18 BS EN 10277-1:2008EN 10277-1:2008 (E) 3 Foreword This document (EN 10277-1:2008) has been prepared by Technical Committee ECISS/TC 23 “Steels for heat treatment, alloy steels and free-cutting steels - Qualities and dimensions”, the secretariat of which is

14、 held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. Attention is drawn to the possi

15、bility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10277-1:1999. According to the CEN/CENELEC Internal Regulations, the national standards o

16、rganizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal

17、, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. This European Standard EN 10277 Bright steel products - Technical delivery conditions is subdivided as follows: Part 1: General; Part 2: Steels for general engineering purposes; Part 3: Free-cutting steels; Part 4: Cas

18、e hardening steels; Part 5: Steels for quenching and tempering. During the preparation of the first edition of this European Standard there were not enough statistical data available concerning mechanical properties of bright bar products. Since then it has been recognized that the proof strength va

19、lues in the cold drawn condition were too high. In addition, cyclic stresses that occur during straightening can reduce the proof strength (Bauschingers effect), which was not taken into account when drafting the first edition of this standard. In this second edition the proof strength values of non

20、-alloy and alloy grades in condition +QT+C in parts 3 and 5 have been adjusted downwards compared to the first edition. BS EN 10277-1:2008EN 10277-1:2008 (E) 4 1 Scope This part of EN 10277 specifies the general technical delivery conditions for bright steel bars in the drawn, turned or ground condi

21、tion, in straight lengths and of the following steel types: a) steels for general engineering purposes as specified in EN 10277-2; b) free-cutting steels as specified in EN 10277-3; c) case hardening steels as specified in EN 10277-4; d) steels for quenching and tempering as specified in EN 10277-5.

22、 It does not cover cold rolled products and cut lengths produced from strip or sheet by cutting. In special cases variations in these technical delivery requirements or additions to them may form the subject of an agreement at the time of enquiry and order (see Annex B). In addition to the specifica

23、tions of this European Standard, the general technical delivery requirements of EN 10021 are applicable, unless otherwise specified. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.

24、 For undated references, the latest edition of the referenced document (including any amendments) applies. EN 606, Bar coding - Transport and handling labels for steel products EN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature EN 10020:2000, Definition

25、and classification of grades of steel EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10052, Vocabulary of heat treatment terms for ferrous pro

26、ducts EN 10079:2007, Definition of steel products EN 10083-2, Steels for quenching and tempering Part 2: Technical delivery conditions for non alloy steels EN 10083-3, Steels for quenching and tempering Part 3: Technical delivery conditions for alloy steels EN 10084, Case hardening steels Technical

27、delivery conditions EN 10204, Metallic products - Types of inspection documents prCEN/TR 10261, Iron and steel - Review of available methods of chemical analysis EN 10277-2, Bright steel products - Technical delivery conditions - Part 2: Steels for general engineering purposes BS EN 10277-1:2008EN 1

28、0277-1:2008 (E) 5 EN 10277-3, Bright steel products - Technical delivery conditions - Part 3: Free-cutting steels EN 10277-4, Bright steel products - Technical delivery conditions - Part 4: Case-hardening steels EN 10277-5, Bright steel products - Technical delivery conditions - Part 5: Steels for q

29、uenching and tempering EN 10278, Dimensions and tolerances of bright steel products EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 643, Steels - Micrographic determination of the apparent grain size (ISO 643:200

30、3) EN ISO 3887, Steels - Determination of depth of decarburization (ISO 3887:2003) EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2005) EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 1

31、4284:1996) 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 10021:2006, EN ISO 377:1997, EN ISO 14284:2002 and the following apply. 3.1 non-alloy and alloy steel; quality and special steel see the terms and definitions in EN 10020:2000 3.2 ste

32、el products steel products are defined according to their shape and dimensions in EN 10079. In particular the following definitions are reproduced 3.2.1 drawn products (3.4.5.1, EN 10079:2007) products of various cross section shapes obtained, after descaling, by drawing of hot rolled bars or rod on

33、 a draw bench (cold deformation without removing material) NOTE This operation gives the product special features with respect to shape, dimensional accuracy and surface finish. In addition, the process causes cold working of the product, which can be eliminated by subsequent heat treatment. Product

34、s in lengths are delivered straightened regardless of size. 3.2.2 turned products (3.4.5.2, EN 10079:2007) round bars produced by turning on a lathe where the product can be further processed by straightening and polishing NOTE 1 This operation gives the bar special features with respect to shape, d

35、imensional accuracy and surface finish. The removal of metal is carried out in such a way that the bright product is generally free from rolling defects and surface decarburization. NOTE 2 For technical reasons some bars ordered as hot rolled products may be delivered roughly turned (peeled), nevert

36、heless such products are treated as hot rolled products and not as bright products. BS EN 10277-1:2008EN 10277-1:2008 (E) 6 3.2.3 ground products (3.4.5.3, EN 10079:2007) drawn or turned round bars given an improved surface quality and dimensional accuracy by grinding or grinding and polishing 3.3 h

37、eat treatment terms terms used in the heat treatment of steel are defined in EN 10052 3.4 ruling section for heat treatment ruling section for heat treatment of a product is the section for which the mechanical properties have been specified (see Annex A). Whatever the actual shape and dimensions of

38、 the cross section of the product, the size of its ruling section is expressed as a diameter. This corresponds to the diameter of an “equivalent round bar” which, at the position of its cross section specified for taking test pieces for mechanical tests, will, when being cooled from the austenitisin

39、g temperature, show the same cooling rate as the actual ruling section of the product concerned at its position for taking test pieces NOTE The term “ruling section” should not be confused with the term “equivalent diameter” as defined in EN 10052. 4 Classification and designation 4.1 Classification

40、 The classification of the relevant steel grades according to EN 10020 is indicated in EN 10277-2 to EN 10277-5. 4.2 Designation 4.2.1 Steel names For the steel grades covered by this European Standard, the steel names as given in the relevant tables of EN 10277-2 to EN 10277-5 are assigned in accor

41、dance with EN 10027-1. 4.2.2 Steel numbers For the steel grades covered by this European Standard, the steel numbers as given in the relevant tables of EN 10277-2 to EN 10277-5 are allocated in accordance with EN 10027-2. 5 Information to be supplied by the purchaser 5.1 Mandatory information The fo

42、llowing information shall be supplied by the purchaser at the time of enquiry and order: a) quantity (mass, number of bars) to be delivered; b) shape of the product (e.g. round, hexagon, square, flat); c) number of the dimensional standard (EN 10278); d) dimensions and tolerances on dimensions; BS E

43、N 10277-1:2008EN 10277-1:2008 (E) 7 e) reference to this European Standard including the number of the part (e.g. EN 10277-3); f) steel name or steel number (see 4.2); g) delivery condition (see 6.3); h) class of surface quality (see 7.7 and Table 1); 5.2 Options The following options may be supplie

44、d by the purchaser and as agreed with the manufacturer: a) reference testing for products used in the quenched and tempered condition (see B.1); b) any fine grain requirement and verification of fine grain size (see 7.4 and B.2); c) any requirement for the verification of non-metallic inclusions (se

45、e 7.5 and B.3); d) depth of decarburization (see 7.6 and B.4); e) additional requirements to the tolerances on shape according to EN 10278; f) temporary corrosion protection (see B.5); g) non-destructive testing (see 7.8 and B.6); h) product analysis (see 7.1.2 and B.7); i) special marking (see 9 an

46、d B.8); j) hardenability requirements for grades of EN 10277-4 and EN 10277-5 (see 7.1.1.2 and 7.3 of EN 10277-4 and EN 10277-5); k) type of inspection document in accordance with EN 10204 (see 8.1). EXAMPLE 2 t round bars with nominal diameter 20 mm, tolerance h9, stock length 6000 mm according to

47、EN 10278 made of steel grade 38SMn28 (1.0760) according to EN 10277-3 in the delivery condition +C, surface quality class 3 and a test report 2.2 as specified in EN 10204. 2t round bars EN 10278 - 20 h9 x stock 6000 EN 10277-3-38SMn28+C - class 3 EN 10204 2.2 or 2t round bars EN 10278 - 20 h9 x stoc

48、k 6000 EN 10277-3-1.0760+C - class 3 EN 10204 2.2 6 Manufacturing process 6.1 Steel making process The steelmaking process shall be at the manufacturers discretion. BS EN 10277-1:2008EN 10277-1:2008 (E) 8 6.2 Manufacture of the product The manufacturing process route of the steel product shall be at

49、 the manufacturers discretion. 6.3 Delivery conditions 6.3.1 Finished condition The steel product shall be delivered in one or a combination of the following finished conditions with or without heat treatment: a) drawn, symbol +C; b) turned, symbol +SH; c) ground, symbol +SL. 6.3.2 Cast separation The products shall be delivered separated by cast. 7 Requirements 7.1 Chemical composition 7.1.1 Cast analysis 7.1.1.1 The chemical composition determined by cast analysis shall be as specified in Table 1 of EN 10277-2 to EN 10277-5. 7.1.1.2 In cases where steels