BS EN 10264-3-2012 Steel wire and wire products Steel wire for ropes Round and shaped non alloyed steel wire for high duty applications《钢丝和钢丝产品 绳索用钢丝 重型装置用圆形和异型非合金钢丝》.pdf

《BS EN 10264-3-2012 Steel wire and wire products Steel wire for ropes Round and shaped non alloyed steel wire for high duty applications《钢丝和钢丝产品 绳索用钢丝 重型装置用圆形和异型非合金钢丝》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10264-3-2012 Steel wire and wire products Steel wire for ropes Round and shaped non alloyed steel wire for high duty applications《钢丝和钢丝产品 绳索用钢丝 重型装置用圆形和异型非合金钢丝》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10264-3:2012Steel wire and wire products Steel wire for ropesPart 3: Round and shaped non alloyed steel wire for high duty applicationsBS EN 10264-3:2012 BRITISH STANDARDNa

2、tional forewordThis British Standard is the UK implementation of EN 10264-3:2012. It supersedes BS EN 10264-3:2002, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of organizations rep

3、resented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012 ISBN 978 0 580 62606 7 ICS 77.140.65 Compliance wi

4、th a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 10264-3:2012EUROPEAN STANDARD NORME EUROP

5、ENNE EUROPISCHE NORM EN 10264-3 January 2012 ICS 77.140.65 Supersedes EN 10264-3:2002English Version Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications Fils et produits trfils en acier - Fils pour cbles - Partie 3: Fils ro

6、nds et profils, en acier non aill, pour fortes sollicitations Stahldraht und Drahterzeugnisse - Stahldraht fr Seile - Teil 3: Runder und profilierter Draht aus unlegiertem Stahl fr hohe Beanspruchungen This European Standard was approved by CEN on 19 November 2011. CEN members are bound to comply wi

7、th the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Mana

8、gement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same st

9、atus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug

10、al, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any

11、 means reserved worldwide for CEN national Members. Ref. No. EN 10264-3:2012: EBS EN 10264-3:2012EN 10264-3:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Designation of the product .54 General conditions of manufacture .55 Characteristics of the wire 55.1 Tensile strength gra

12、des 55.2 Profiles 65.2.1 Definition of shaped wire 65.2.2 Equivalent diameter .85.3 Minimum requirements for wire characteristics .85.3.1 Dimension measured values .85.3.2 Reverse bend test 95.3.3 Torsion test . 125.3.4 Zinc and Zn95/Al5 coatings . 146 Test methods . 156.1 General . 156.2 Reverse be

13、nd test . 15BS EN 10264-3:2012EN 10264-3:2012 (E) 3 Foreword This document (EN 10264-3:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publi

14、cation of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall

15、not be held responsible for identifying any or all such patent rights. This document supersedes EN 10264-3:2002. This European Standard for wire for ropes is made up of the following parts: Part 1: General requirements Part 2: Cold drawn non alloy steel wire for ropes for general applications Part 3

16、: Round and shaped non alloyed steel wire for high duty applications Part 4: Stainless steel wire This European Standard has been technically revised to incorporate the following changes: a) heavy duty applications have been explained in the new last sentence of the scope; b) the purity of the zinc

17、coating of the drawn wire has been specified according the relevant EN 1179 (see Clause 4); c) a footnote c) has been added in Table 1 in order to precise the meaning of coated; d) the values of the Z and H profiles have been updated in Table 2; e) a note has been added to allow other wire diameters

18、 higher than those given in Table 3 “Dimensional tolerances on round wire diameter“ subject to an agreement between supplier and user at the time of order; f) modifications have been made on values concerning “Coated Class A“ given in Table 4 “Dimensional tolerances for shaped wire“; g) modification

19、s have been made in Table 5 “Minimum number of reverse bends for shaped wire for static applications“ concerning the values of Z profile for the height of profile upper to 5 mm; h) a second quality of zinc coating has been added for dynamic applications (see 5.3.4); i) three additional ranges for No

20、minal dimensions of round wire (from 0,50 mm to 0,80 mm) have been added (see Table 11 “Minimum mass of coating“). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulga

21、ria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10264

22、-3:2012EN 10264-3:2012 (E) 4 1 Scope This part of this European Standard specifies round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications. Heavy duty refers to

23、situations where the stresses applied to the rope are either high or vary by a large amount during service. This part of this European Standard refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T). In addition to the requirements of this part of this

24、 European Standard, the requirements of EN 10264-1 also apply. It does not apply to steel wire taken from manufactured ropes. This part of this European Standard specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications: dimensional tolerances; mechanical cha

25、racteristics; requirements relating to the chemical composition of the steel wire; conditions to be satisfied by any coating. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For un

26、dated references, the latest edition of the referenced document (including any amendments) applies. EN 1179, Zinc and zinc alloys Primary zinc EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10244-2, Steel wire and wire products Non-ferrous metallic coatings on steel wire Pa

27、rt 2: Zinc or zinc alloy coatings EN 10264-1:2011, Steel wire and wire products Steel wire for ropes Part 1: General requirements EN ISO 16120-1:2011, Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1:2011) EN ISO 16120-2:2011, Non-alloy steel wire rod for c

28、onversion to wire - Part 2: Specific requirements for general-purpose wire rod (ISO 16120-2:2011) EN ISO 16120-4:2011, Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4:2011) BS EN 10264-3:2012EN 10264-3:2012 (E) 5 3 De

29、signation of the product The designation of wire for ropes manufactured in accordance with this European Standard shall be based on the nominal dimension, surface appearance and tensile strength. The indicator of dimension for round wire is the nominal diameter; for shaped wire it is the value of th

30、e height (h), followed by a letter specifying the profile. In the case of H profiles, this indicator shall be followed by the value of the narrowing. The surface appearance shall be indicated as defined in EN 10264-1 with U for uncoated or bright wire, with a letter indicating the class of coating (

31、A, B, ) and in the case of zinc alloy coatings, indicating in brackets (Zn/Al). EXAMPLE 1 2,0 mm wire for rope with thick zinc layer, class A, tensile strength grade 1 570 MPa, in accordance with EN 10264-3. Designation: wire for rope EN 10264-3 2,0 - A 1 570 EXAMPLE 2 Wire for rope, trapezoidal pro

32、file, h = 3,5 mm, class B zinc coated, tensile strength grade 1 770 MPa, in accordance with EN 10264-3. Designation: wire for rope EN 10264-3 - T3,5 - B 1 770 EXAMPLE 3 H shaped wire for rope h = 3,0 mm, w = 1,8 mm, coated with class A zinc alloy, tensile strength grade 1 370 MPa, in accordance with

33、 EN 10264-3. Designation: wire for rope EN 10264-3 - H 3,0 1,8 - A (Zn/Al) 1 370 4 General conditions of manufacture The drawn wire shall be manufactured from rod in accordance with EN ISO 16120-1 and EN ISO 16120-2 for ropes for static applications, and in accordance with EN ISO 16120-1 and EN ISO

34、16120-4 for ropes for dynamic applications. The drawn wire shall show no surface defects or internal defects prejudicial to its use. When specified, the drawn wire shall be supplied with a coating applied by a hot dipping or electrolytic method. The coatings commonly used are zinc or Zn95/Al5. Unles

35、s otherwise specified, the zinc used for coating shall have a purity of 99,95 % according to EN 1179, Z3, other zinc alloys may be agreed at the time of enquiry and order. NOTE If required by the purchaser, the quality of the zinc or zinc alloy used for the coating material (zinc or zinc alloy) shou

36、ld be certified by the manufacturer. Because of the reaction between the base material and coating material, which is inherent to the process, the composition of the coating on the wire is different to that used in the coating bath. 5 Characteristics of the wire 5.1 Tensile strength grades The tensi

37、le strength grades are defined in Table 1. NOTE The nominal values are the minimum tensile strength limits. The upper limits (maximum) are equal to these minimum values increased with the tolerances specified in EN 10264-1:2011, Table 1. BS EN 10264-3:2012EN 10264-3:2012 (E) 6 Table 1 Tensile streng

38、th grade Quality of wire cNominal tensile strength grade MPa aRound Bright or coated Class B 1 570 1 770 1 960 2 160 Zinc or Zn95/Al5 - Class A 1 570 1 770 Shaped Bright or coated Class B 1 370 1 570 1 770 or class D b1 270 1 370 1 470 1 570 1 670 1 770 Zinc or Zn95/Al5 - Class A 1 370 1 570 NOTE Su

39、bject to agreement between the manufacturer and the purchaser, other tensile strength grades can be used.a1 MPa = 1 N/mm2. bMass of coatings for static and dynamic applications are specified in Table 11. cCoated means zinc or Zn95/Al5 alloy. 5.2 Profiles 5.2.1 Definition of shaped wire For shaped wi

40、re, the characteristic sections of the wire are shown in Figure 1 for full lock Z, half lock H and trapezoidal T wires. The nominal dimensions and tolerances shall be agreed between the supplier and the purchaser at the time of ordering. The conventional characteristic values are as follows: h heigh

41、t: difference between the radii of the 2 concentric boundary circles; b width: maximum width of upper part perpendicular to a radial line passing through the centre of the width (as shown in Figure 1); w minimum narrowing: smallest width of the profile; e distance taken diagonally across the transve

42、rse section of the profile (essentially T or Z profiles). The designation of a full lock wire is established using the letter Z and the height (h), that of a half lock wire by H followed by the height (h) and the minimum narrowing (w) (h w) and that of a trapezoidal wire by the letter T followed by

43、the height (h). Table 2 gives the design criteria for the shaped wire shown in Figure 1. These are the relation between the height of the shaped wires and the other major characteristic dimensions. BS EN 10264-3:2012EN 10264-3:2012 (E) 7 Figure 1 Shaped wire sections Table 2 Design criteria for shap

44、ed wire Ratio Z profile H profile Trapezoidal profile T h : b 0,9 to 1,55 - 1,0 to 1,3 h : e 0,55 to 0,80 - 0,75 to 0,90 h : w - 0,8 to 2,3 BS EN 10264-3:2012EN 10264-3:2012 (E) 8 5.2.2 Equivalent diameter The definition of the equivalent diameter of shaped wire is as follows. The diameter of the eq

45、uivalent transverse circular section (a) is the diameter of a circle with the same transverse section surface area as the shaped wire. The diameter of the equivalent circular circumference (c) is the diameter of the circle with the same perimeter as the shaped wire. Nominal values may be measured by

46、 planimetry on the drawing of the shaped wire. If the surface area of the transverse section of the shaped wire is A and the perimeter C, the equivalent values are calculated as follows: equivalent a = AA24= equivalent c = C5.3 Minimum requirements for wire characteristics 5.3.1 Dimension measured v

47、alues The measured values for the round wire shall satisfy the requirements of Table 3. Ovality shall not be greater than half the tolerance specified in Table 3. Table 3 Dimensional tolerances on round wire diameter Dimensions in millimetres Nominal diameter of wire Tolerance on diameter () d Brigh

48、t and coated a Class B Coated a Class A 0,50 d 1,00 0,015 0,030 1,00 d 1,65 0,020 0,040 1,65 d 1,80 0,020 0,050 1,80 d 2,05 0,025 0,050 2,05 d 2,80 0,025 0,060 2,80 d 4,00 0,030 0,070 a Coated means zinc or Zn95/Al5 alloy. NOTE Wire diameters higher than those currently mentioned are possible with a

49、n agreement between the supplier and the user during the order. This agreement should specified the corresponding characteristics.In the case of shaped wire, the measured values for the characteristic “h“ shall satisfy the tolerance requirements in Table 4. The other dimensions shall be agreed at the time of enquiry and order. BS EN 10264-3:2012EN 10264-3:2012 (E) 9 Table 4 Dimensional