BS EN 10106-2015 Cold rolled non-oriented electrical steel strip and sheet delivered in the fully processed state《经完全处理后交付的冷轧非定向电工钢板和钢带》.pdf

《BS EN 10106-2015 Cold rolled non-oriented electrical steel strip and sheet delivered in the fully processed state《经完全处理后交付的冷轧非定向电工钢板和钢带》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10106-2015 Cold rolled non-oriented electrical steel strip and sheet delivered in the fully processed state《经完全处理后交付的冷轧非定向电工钢板和钢带》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 10106:2015Cold rolled non-orientedelectrical steel strip and sheetdelivered in the fully processedstateBS EN 10106:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10106:2015. Itsupersedes BS EN 10106:2007 which is withdrawn.Th

2、e UK participation in its preparation was entrusted to TechnicalCommittee ISE/108, Magnetic Alloys and Steels.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users

3、 are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83974 0ICS 77.140.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the

4、Standards Policy and Strategy Committee on 31 October 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 10106:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10106 October 2015 ICS 77.140.50 Supersedes EN 10106:2007English Version Cold rolled non-oriented

5、electrical steel strip and sheet delivered in the fully processed state Bandes et tles en acier lectrique grains non orients lamines froid et livres ltat fini Kaltgewalztes nicht kornorientiertes Elektroband und -blech im schlussgeglhten Zustand This European Standard was approved by CEN on 29 Augus

6、t 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtai

7、ned on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN

8、-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,

9、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre:

10、Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10106:2015 EBS EN 10106:2015EN 10106:2015 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions .

11、 5 4 Classification and designation 6 4.1 Classification . 6 4.2 Designation 6 5 Information supplied by the purchaser 6 5.1 Mandatory information 6 5.2 Options 7 5.3 Example of an order . 7 6 General requirements . 7 6.1 Production process . 7 6.2 Form of supply 7 6.3 Delivery condition 8 6.4 Surfa

12、ce condition 8 6.5 Suitability for cutting . 8 7 Technical requirements 8 7.1 Magnetic properties . 8 7.1.1 General 8 7.1.2 Magnetic polarization 8 7.1.3 Specific total loss . 9 7.1.4 Anisotropy of loss 9 7.2 Geometric characteristics and tolerances 10 7.2.1 Thickness 10 7.2.2 Width 11 7.2.3 Length

13、. 12 7.2.4 Edge camber . 12 7.2.5 Flatness (wave factor) 12 7.2.6 Residual curvature 12 7.3 Technological characteristics 12 7.3.1 Density . 12 7.3.2 Stacking factor . 12 7.3.3 Number of bends 12 7.3.4 Internal stresses . 12 8 Inspection and testing 13 8.1 General . 13 8.2 Selection of samples 13 8.

14、3 Preparation of test specimens . 13 8.3.1 Magnetic properties 13 8.3.2 Geometrical characteristics and tolerances . 14 8.3.3 Technological characteristics 14 8.4 Test methods . 14 BS EN 10106:2015EN 10106:2015 (E) 3 8.4.1 General . 14 8.4.2 Magnetic properties. 14 8.4.3 Geometrical characteristics

15、and tolerances . 15 8.4.4 Technological characteristics 15 8.5 Retests 16 9 Marking, labelling and packaging . 16 10 Complaints 16 Annex A (normative) Options 17 Annex B (informative) Non-specified magnetic properties . 18 Annex C (informative) Density determination 19 Annex D (informative) Minimum

16、stacking factor for coated products 20 Annex E (informative) Changes to the previous version EN 10106:2007 . 21 Bibliography . 22 BS EN 10106:2015EN 10106:2015 (E) 4 European foreword This document (EN 10106:2015) has been prepared by Technical Committee ECISS/TC 108 “Steel sheet and strip for elect

17、rical applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2016, and conflicting national standards shall be withdrawn at the latest by Apr

18、il 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10106:2007. Regarding the changes that were made

19、in this new edition of EN 10106, see Annex E. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Form

20、er Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10106:2015EN 10106:2015 (E) 5 1 Sco

21、pe This European Standard specifies cold-rolled non-oriented electrical steel strip and sheet in nominal thicknesses of 0,35 mm, 0,50 mm, 0,65 mm and 1,00 mm. In particular, it specifies general requirements, the magnetic properties, geometric characteristics and tolerances, technological characteri

22、stics as well as the inspection procedure. This European Standard applies to materials supplied in the fully annealed condition intended for the construction of magnetic circuits. It does not apply to semi-processed material. These magnetic materials correspond to IEC 60404-1:2000, C.2.3.2.1. 2 Norm

23、ative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

24、 applies. EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steels Part 1: Steel names EN 10027-2, Designation systems for steels Part 2: Numerical system EN 10204, Metallic products Types of inspection documents EN 10251, Magnetic materials Metho

25、ds of determination of the geometrical characteristics of electrical steel sheet and strip EN 10280, Magnetic materials Methods of measurement of the magnetic properties of electrical sheet and strip by means of a single sheet tester EN 10342, Magnetic materials Classification of surface insulations

26、 of electrical steel sheet, strip and laminations EN 60404-2, Magnetic materials Part 2: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of an Epstein frame (IEC 60404-2) EN 60404-13, Magnetic materials Part 13: Methods of measurement of density, resist

27、ivity and stacking factor of electrical steel sheet and strip (IEC 60404-13) EN ISO 7799, Metallic materials Sheet and strip 3 mm thick or less Reverse bend test (ISO 7799) IEC 60050-121, International Electrotechnical Vocabulary Chapter 121: Electromagnetism IEC 60050-221, International Electrotech

28、nical Vocabulary Chapter 221: Magnetic materials and components 3 Terms and definitions For the purposes of this document, the terms and definitions of the principal terms relative to magnetic properties given in IEC 60050-121 and IEC 60050-221 and the following apply. BS EN 10106:2015EN 10106:2015

29、(E) 6 3.1 edge camber greatest distance between a longitudinal edge of the sheet and the line joining the two extremities of the measured length of this edge 3.2 flatness property of a sheet or a length of strip which is characterized by the wave factor, i.e. by the relation of the height of the wav

30、e to its length 3.3 number of bends number of alternate bends possible before the appearance of the first crack in the base metal visible to the naked eye indicating the ductility of the material 3.4 internal stresses stresses that are characterized by a deviation in relation to the line of cutting

31、4 Classification and designation 4.1 Classification The grades covered by this European Standard are classified according to the value of the maximum specific total loss in watts per kilogram and according to the nominal thickness of the material (0,35 mm, 0,50 mm, 0,65 mm and 1,00 mm). 4.2 Designat

32、ion For the steel grades covered by this European Standard, the steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. The steel name comprises the following in the order given: a) capital letter M for electrical steel; b) number of on

33、e hundred times the specified value of maximum specific total loss at 50 Hz, in watts per kilogram and corresponding to the nominal product thickness, at 1,5 T; c) one hundred times the nominal thickness of the material, in millimetres; d) characteristic letter A for non-oriented electrical sheet or

34、 strip supplied in the fully processed state. EXAMPLE Non-oriented electrical steel sheet or strip with a maximum specific total loss at 1,5 T of 2,50 W/kg at 50 Hz, a nominal thickness of 0,35 mm, supplied in the fully processed state: M25035A. 5 Information supplied by the purchaser 5.1 Mandatory

35、information For material to adequately comply with the requirements of this standard, the purchaser shall include the following information in their enquiry or order: BS EN 10106:2015EN 10106:2015 (E) 7 a) quantity; b) type of product (strip or sheet); c) number of this European Standard (EN 10106);

36、 d) steel name or number (see 4.2); e) dimensions of sheets or strips required (including any limitation on the external diameter of a coil) (see 6.2 and 7.2.2); f) axis of coil (horizontal or vertical) (see 6.2); g) internal diameter of coil (508 mm or 610 mm) (see 6.2); h) limitation on the mass o

37、f a bundle of sheets or of a coil or limitation of external diameter (see 6.2); i) limitation of the mass of the packing unit (see 6.2); j) type of inspection procedure, and for specific inspection type of the related document (see 8.1). 5.2 Options A number of options are specified in this standard

38、 and listed in Annex A. lf the purchaser does not indicate his wish to implement one of these options, the products shall be supplied in accordance with the basis specification of this standard (see 5.1). 5.3 Example of an order 18 t strip with 0,35 mm thickness in accordance with EN 10106, made of

39、steel grade M270-35A, delivered in coils with a width of 1 000 mm and a maximum mass of 3 500 kg, vertical coil axis (v), with specific inspection, inspection report 3.1 in accordance with EN 10204: 18 t strip EN 10106 M270-35A 1000 mm max. 3500 kg v 3.1 6 General requirements 6.1 Production process

40、 The production process of the steel and its chemical composition are left to the discretion of the manufacturer. 6.2 Form of supply For sheets the material is supplied in bundles and for strip the material is supplied in coils. The mass of bundles of sheets or the mass and/or the external diameter

41、of coils shall be agreed at the time of enquiry and order. The mass of the package unit shall be agreed at the time of enquiry and order. The recommended value for the internal diameter of coils is 508 mm or 610 mm. The direction of coils, horizontal (h) or vertical (v), shall be agreed at the time

42、of enquiry and order. BS EN 10106:2015EN 10106:2015 (E) 8 Sheets that make up each bundle shall be stacked so that the side faces are substantially flat and approximately perpendicular to the top face. Strip shall be of constant width and wound in such a way that the edges are superimposed in a regu

43、lar manner and that the side faces of the coil are substantially flat. Coils shall be sufficiently tightly wound so that they do not collapse under their own weight. Strip may exhibit welds resulting from removing defective zones if agreed at the time of enquiry and order. If necessary the marking o

44、f welds may be agreed at the time of enquiry and order. For coils containing welds, each part of the strip shall be of the same grade. The edges of parts welded together shall not be so much out of alignment as to affect further processing of the material. 6.3 Delivery condition The material may be

45、supplied either without insulation or with insulation on one or both sides in accordance with EN 10342. lf the material is supplied with insulation, the nature of the insulation, its thickness and properties, the stacking factor and their verification shall be agreed at the time of enquiry and order

46、 (see Annex A, Option 2) and in accordance with the values stated in Table D.1. 6.4 Surface condition The surfaces shall be smooth and clean, free from grease and rust1). Dispersed defects such as scratches, blisters, cracks, etc. are permitted if the products are within the tolerances and if these

47、defects are not detrimental to the correct use of the supplied material. When an insulation coating is present on the surface of the material, it shall be sufficiently adherent so that the coating does not become detached during cutting operations. During the alternating bend test (see 8.4.4.2), the

48、 coating shall not be detached after a bend of 90. If the coating becomes detached during the test, the piece from which the sample was taken shall be subjected to a shearing test. During this test, it shall not be admissible for large pieces of the coating to become detached; however, slight chippi

49、ng of this coating at the shearing edges shall be tolerated. 6.5 Suitability for cutting The material shall be able to be cut or punched at any point and in the usual shapes, thus ensuring accurate working with the correct cutting tools. 7 Technical requirements 7.1 Magnetic properties 7.1.1 General The properties defined in 7.1.2 to 7.1.4 are applicable to products in the delivery conditions defined in 6.3. For coated products, the mass of the insulation coating should be taken into account. 7.1.2 Magnetic polarization The m