BS EN 10088-4-2009 Stainless steels nPart 4 Technical delivery conditions nfor sheet plate and strip of corrosion nresisting steels for construction npurposes《不锈钢 第4部分 建筑用耐蚀薄钢板 厚钢板.pdf

《BS EN 10088-4-2009 Stainless steels nPart 4 Technical delivery conditions nfor sheet plate and strip of corrosion nresisting steels for construction npurposes《不锈钢 第4部分 建筑用耐蚀薄钢板 厚钢板.pdf》由会员分享，可在线阅读，更多相关《BS EN 10088-4-2009 Stainless steels nPart 4 Technical delivery conditions nfor sheet plate and strip of corrosion nresisting steels for construction npurposes《不锈钢 第4部分 建筑用耐蚀薄钢板 厚钢板.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN10088-4:2009ICS 77.140.20; 77.140.50NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDStainless steelsPart 4: Technical delivery conditionsfor sheet/plate and strip of corrosionresisting steels for constructionpurposesThis British Standardwas published under

2、theauthority of the StandardsPolicy and StrategyCommittee on 31 May 2009 BSI 2009ISBN 978 0 580 54855 0Amendments/corrigenda issued since publicationDate CommentsBS EN 10088-4:2009National forewordThis British Standard is the UK implementation of EN 10088-4:2009.The UK participation in its preparati

3、on was entrusted to TechnicalCommittee ISE/30, Stainless steels.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.C

4、ompliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 10088-4:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10088-4April 2009ICS 77.140.20; 77.140.50English VersionStainless steels - Part 4: Technical delivery conditions forsheet/plate and strip of corrosion re

5、sisting steels for constructionpurposesAciers inoxydables - Partie 4: Conditions techniques delivraison des tles et bandes en acier rsistant lacorrosion pour usage de constructionNichtrostende Sthle - Teil 4: TechnischeLieferbedingungen fr Blech und Band auskorrosionsbestndigen Sthlen fr das Bauwese

6、nThis European Standard was approved by CEN on 21 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical ref

7、erences concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member i

8、nto its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

9、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009

10、CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10088-4:2009: EBS EN 10088-4:2009EN 10088-4:2009 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Designation and ordering .6 4.1 Designati

11、on of steel grades 6 4.2 Order designation 6 5 Classification of grades 7 6 Requirements .8 6.1 Steelmaking process .8 6.2 Delivery condition 8 6.3 Chemical composition 8 6.4 Chemical corrosion properties .8 6.5 Mechanical properties .8 6.6 Surface quality .9 6.7 Internal soundness 9 6.8 Formability

12、 at room temperature .9 6.9 Dimensions and tolerances on dimensions and shape 9 6.10 Calculation of mass and tolerances on mass .9 7 Inspection and testing .9 7.1 General 9 7.2 Agreement on tests and inspection documents . 10 7.3 Specific inspection and testing . 10 7.4 Test methods . 10 7.5 Retests

13、 . 11 8 Evaluation of Conformity . 11 8.1 General . 11 8.2 Initial type testing . 11 8.3 Factory production control (FPC) . 12 9 Marking 14 10 Dangerous substances 14 Annex A (informative) Guidelines for further treatment (including heat treatment) in fabrication 34 Annex B (normative) Applicable di

14、mensional standards . 38 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive 39 Bibliography . 45 BS EN 10088-4:2009EN 10088-4:2009 (E) 3 Foreword This document (EN 10088-4:2009) has been pre

15、pared by Technical Committee ECISS/TC 23 “Steels for heat treatment, alloy steels and free-cutting steels - Qualities and dimensions”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by en

16、dorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by January 2011. EN 10088, under the general title “Stainless steels“, consists of the following parts: Part 1: List of stainless steels (including a table of European Standards, in which th

17、ese stainless steels are further specified, see Annex D); Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes; Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion

18、resisting steels for general purposes; Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes; Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purp

19、oses. The European Committee for Standardisation (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of patents concerning two steel grades. The holder of these patent rights has assured the CEN that he/she is willing to negotiate licences unde

20、r reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with CEN and/or CENELEC. Information may be obtained from: Sandvik AB SE-811 81 SANDVIKEN Sweden for grade 1.4477 Outokumpu S

21、tainless AB SE-77480 AVESTA Sweden for grade 1.4162 CEN takes no position concerning the evidence, validity and scope of this patent right. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. CEN shal

22、l not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). BS EN 10088-4:2009EN 10088-4:2009 (E) 4 Fo

23、r relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyp

24、rus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 10088-4:2009EN 10088-4:2009 (E

25、) 5 1 Scope The scope of this part of EN 10088 is to specify the technical delivery conditions for hot or cold rolled sheet/plate and strip of standard and special grades of corrosion resisting stainless steels for construction purposes in addition to the general technical delivery conditions specif

26、ied in EN 10021. This European Standard does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing. 2 Normative references The following referenced documents are indispensable for the a

27、pplication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature EN 10002-5, Me

28、tallic materials - Tensile testing - Part 5: Method of testing at elevated temperature EN 10021, General technical delivery requirements for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10045-

29、1, Metallic materials - Charpy impact test - Part 1: Test method EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel products EN 10088-1:2005, Stainless steels - Part 1: List of stainless steels EN 10088-2, Stainless steels Part 2: Technical deli

30、very conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plates and wide flats EN 10168:2004, Steel products Inspection documents List of informat

31、ion and description EN 10204, Metallic products - Types of inspection documents CEN/TR 10261, Iron and steel Review of available methods of chemical analysis EN 10307, Non-destructive testing - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal

32、 to or greater than 6 mm (reflection method) EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels - Part 2: Ferritic, austenitic and f

33、erritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulphuric acid (ISO 3651-2:1998) EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2005) BS EN 10088-4:2009EN 10088-4:2009 (E) 6 EN ISO 6507-1, Metallic materials - Vickers har

34、dness test - Part 1: Test method (ISO 6507-1:2005) EN ISO 6508-1, Metallic materials - Rockwell hardness test - Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-1:2005) EN ISO 9001:2008, Quality management systems - Requirements (ISO 9001:2008) EN ISO 14284, Steel and iron - Sa

35、mpling and preparation of samples for the determination of chemical composition (ISO 14284:1996) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 stainless steels the definition in EN 10088-1:2005 applies 3.2 corrosion resisting steels steels

36、with at least 10,5 % Cr and max. 1,20 % C if their resistance to corrosion is of primary importance 3.3 product forms the definitions in EN 10079:2007 apply 3.4 types of heat-treatment the definitions in EN 10052:1993 apply 3.5 standard grades grades with a relatively good availability and a wider r

37、ange of application 3.6 special grades grades for special use and/or with limited availability 4 Designation and ordering 4.1 Designation of steel grades The steel names and steel numbers (see Tables 1 to 4) are allocated in accordance with EN 10027-1 and EN 10027-2 respectively. 4.2 Order designati

38、on The complete designation for ordering a product according to this European Standard shall contain the following information: a) the desired quantity; b) the product form (e.g.: strip or sheet/plate); BS EN 10088-4:2009EN 10088-4:2009 (E) 7 c) the nominal dimensions, the number of the appropriate

39、European Standard (see Annex B) plus any choice of requirements; d) the type of material (steel); e) the number of this European Standard; f) the steel name or steel number; g) the symbol for the desired heat treatment or cold worked condition, if for the relevant steel in the tables for the mechani

40、cal properties more than one treatment condition is covered; h) the desired process route (see symbols in Table 6); i) verification of internal soundness, if required (flat products with thickness 6 mm shall be tested in accordance with EN 10307); j) the type of inspection certificate (3.1 or 3.2) a

41、ccording to EN 10204; k) regulatory marking requirements (see Annex ZA). EXAMPLE 10 plates of a steel grade with the name X5CrNi18-10 and the number 1.4301 as specified in EN 10088-4 with nominal dimensions thickness = 8 mm, width = 2000 mm, length = 5000 mm; tolerances on dimensions, shape and mass

42、 as specified in EN 10029 with thickness tolerance class B and “normal“ flatness tolerance class, in process route 1D (see Table 6), inspection certificate 3.1 as specified in EN 10204 and declaration of conformity: 10 plates EN 10029-8B x 2000 x 5000 Steel EN 10088-4 - X5CrNi18-10+1D Inspection cer

43、tificate 3.1, CE or 10 plates EN 10029-8B x 2000 x 5000 Steel EN 10088-4 - 1.4301+1D Inspection certificate 3.1, CE 5 Classification of grades Steels covered in this European Standard are classified according to their structure into a) ferritic steels; b) martensitic steels; c) precipitation hardeni

44、ng steels; d) austenitic steels; e) austenitic-ferritic steels. See also Annex B to EN 10088-1:2005. BS EN 10088-4:2009EN 10088-4:2009 (E) 8 6 Requirements 6.1 Steelmaking process Unless a special steelmaking process is agreed at the time of enquiry and order, the steelmaking process for steels conf

45、orming to this European Standard shall be at the discretion of the manufacturer. 6.2 Delivery condition The products shall be supplied by reference to the process route given in Table 6 and, where different alternatives exist, to the treatment conditions given in Tables 7 to 11, 13 and 14 (see also

46、Annex A). 6.3 Chemical composition 6.3.1 The requirements given in Tables 1 to 4 shall apply with respect to the chemical composition according to the cast analysis. If grades other than those included in this European Standard are required for construction purposes, they shall comply with EN 10088-

47、2 and be in conjunction with the requirements of this European Standard. 6.3.2 The product analysis may deviate from the limiting values for the cast analysis given in Tables 1 to 4 by the values listed in Table 5. 6.4 Chemical corrosion properties Referring to resistance to intergranular corrosion

48、as defined in EN ISO 3651-2, for ferritic, austenitic and austenitic-ferritic steels the specification in Tables 7, 10 and 11 shall apply. EN ISO 3651-2 shall not be applicable for testing martensitic and precipitation hardening steels. NOTE The corrosion resistance of stainless steels is very depen

49、dant on the type of environment and can therefore not always be clearly ascertained through laboratory tests. It is therefore advisable to draw on the available experience of the use of the steels. 6.5 Mechanical properties 6.5.1 The mechanical properties at room temperature as specified in Tables 7 to 11 shall apply for the relevant specified heat treatment condition. This does not apply to the process route 1U (hot rolled, not heat treated, not descaled). If the products are to be supplied in a non-heat-treated condition, the mechanical properties specified in 7