BS EN 10088-2-2014 Stainless steels Technical delivery conditions for sheet plate and strip of corrosion resisting steels for general purposes《不锈钢 一般用途耐腐蚀钢薄板 板材和带材的交货技术条件》.pdf

《BS EN 10088-2-2014 Stainless steels Technical delivery conditions for sheet plate and strip of corrosion resisting steels for general purposes《不锈钢 一般用途耐腐蚀钢薄板 板材和带材的交货技术条件》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10088-2-2014 Stainless steels Technical delivery conditions for sheet plate and strip of corrosion resisting steels for general purposes《不锈钢 一般用途耐腐蚀钢薄板 板材和带材的交货技术条件》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 10088-2:2014Stainless steelsPart 2: Technical delivery conditions forsheet/plate and strip of corrosion resistingsteels for general purposesBS EN 10088-2:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10088-2:2014. It superse

2、des BS EN 10088-2:2005 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/105, Steels for Heat Treatment, Alloy Steels, Free-Cutting Steels and Stainless Steels.A list of organizations represented on this committee can be obtained on request to its se

3、cretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 76855 2ICS 77.140.20; 77.140.50Compliance with a British St

4、andard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 10088-2:2014EUROPEAN STANDARD NORME EUROPENNE

5、 EUROPISCHE NORM EN 10088-2 October 2014 ICS 77.140.20; 77.140.50 Supersedes EN 10088-2:2005English Version Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes Aciers inoxydables - Partie 2: Conditions techniques de li

6、vraison des tles et bandes en acier de rsistance la corrosion pour usage gnral Nichtrostende Sthle - Teil 2: Technische Lieferbedingungen fr Blech und Band aus korrosionsbestndigen Sthlen fr allgemeine VerwendungThis European Standard was approved by CEN on 9 August 2014. CEN members are bound to co

7、mply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENEL

8、EC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the

9、same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

10、rg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

11、2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10088-2:2014 EBS EN 10088-2:2014EN 10088-2:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Designation and ord

12、ering .6 4.1 Designation of steel grades 6 4.2 Designation to be used on ordering 6 5 Classification of grades 7 6 Requirements .8 6.1 Steelmaking process .8 6.2 Delivery condition 8 6.3 Chemical composition 8 6.4 Chemical corrosion properties .8 6.5 Mechanical properties .8 6.6 Surface quality .8 6

13、.7 Internal soundness 9 6.8 Formability at room temperature .9 6.9 Dimensions and tolerances on dimensions and shape 9 6.10 Calculation of mass and tolerances on mass .9 7 Inspection and testing .9 7.1 General 9 7.2 Agreement on tests and inspection documents . 10 7.3 Specific inspection and testing

14、 . 10 7.3.1 Extent of testing 10 7.3.2 Selection and preparation of samples and test pieces. 10 7.4 Test methods . 10 7.5 Retests . 11 8 Marking 11 Annex A (informative) Guidelines for further treatment (including heat treatment) in fabrication 51 Annex B (informative) Applicable dimensional standar

15、ds. 57 Bibliography . 58 BS EN 10088-2:2014EN 10088-2:2014 (E) 3 Foreword This document (EN 10088-2:2014) has been prepared by Technical Committee ECISS/TC 105 “Steels for heat treatment, alloy steels, free-cutting steels and stainless steels”, the secretariat of which is held by DIN. This European

16、Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2015 and conflicting national standards shall be withdrawn at the latest by April 2015. Attention is drawn to the possibility that some of the elements of t

17、his document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10088-2:2005. This standard mainly differs from the 2005 edition as follows: a) addition of austenitic grades 1.4618, 1.4376,

18、1.4640, 1.4646, addition of austenitic-ferritic (duplex) grades 1.4162, 1.4662, 1.4482, 1.4062, addition of ferritic grades 1.4600, 1.4607, 1.4611, 1.4613, 1.4630, 1.4634; b) chemical composition was changed for following grades: austenitic grade 1.4371, 1.4597, austenitic-ferritic grade 1.4362; c)

19、standard inspection document is now a test report 2.2 according to EN 10204; d) products delivered with hot-rolled or cold-rolled finishes shall be supplied with a prime surface; e) a new cold rolled surface finish (2A) has been introduced for ferritic stainless steel grades that have been bright-pi

20、ckled and skin passed; f) mechanical values have been changed for austentic grade 1.4372, for ferritic grades 1.4016 and for martensitic grade 1.4034. EN 10088, under the general title Stainless steels, consists of the following parts: Part 1: List of stainless steels (including a table of European

21、Standards, in which these stainless steels are further specified, see Annex B); Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes the present document; Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire,

22、 sections and bright products of corrosion resisting steels for general purposes; Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes; Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corro

23、sion resisting steels for construction purposes. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, F

24、ormer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10088-2:2014EN 10088-2:2014 (E)

25、4 Introduction The European Organization for Standardization (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of patents applied to seven steel grades. CEN takes no position concerning the evidence, validity and scope of these patent rights.

26、 The holder of these patent rights has ensured CEN that they are willing to negotiate licenses, under reasonable and non-discriminatory terms and conditions, with applicants throughout the world. In this respect, the statements of the holders of these patent rights are registered with CEN. Informati

27、on may be obtained from: Grade 1.4162, 1.4662 Outokumpu Stainless AB SE-77480 Avesta, Sweden Grade 1.4062 Ugitech F-73403 Ugine Cedex, France Grade 1.4062 Industeel F-71200 Creusot, 56 Rue Clemenceau, France Grade 1.4646, 1.4611, 1.4613 Acciai Speciali Terni I-05100 Terni, Italy BS EN 10088-2:2014EN

28、 10088-2:2014 (E) 5 1 Scope This European Standard specifies the technical delivery conditions for hot or cold rolled sheet/plate and strip of standard grades and special grades of corrosion resisting stainless steels for general purposes. NOTE General purposes include the use of stainless steels in

29、 contact with foodstuffs. The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard. This European Standard does not apply to components manufactured by further processing of

30、 the product forms listed above with quality characteristics altered as a result of such further processing. 2 Normative references The following referenced documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, on

31、ly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steels Part 1: Steel names EN 10027-2, Designation systems fo

32、r steels Part 2: Numerical system EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel products EN 10088-1:2014, Stainless steels Part 1: List of stainless steels EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates,

33、wide flats and sections Part 2: Plate and wide flats EN 10168, Steel products Inspection documents List of information and description EN 10204, Metallic products Types of inspection documents EN 10307, Non-destructive testing Ultrasonic testing of austenitic and austenitic-ferritic stainless steels

34、 flat products of thickness equal to or greater than 6 mm (reflection method) EN ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method (ISO 148-1) EN ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377) EN ISO

35、3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulfuric acid (ISO 3651-2) EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method

36、(ISO 6506-1) EN ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method (ISO 6507-1) EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-1) BS EN 10088-2:2014EN 10088-2:2014 (E) 6 EN ISO 6892-1, Metallic mat

37、erials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1) EN ISO 6892-2, Metallic materials Tensile testing Part 2: Method of test at elevated temperature (ISO 6892-2) EN ISO 14284, Steel and iron Sampling and preparation of samples for the determination of chemical composition

38、(ISO 14284) 3 Terms and definitions For the purposes of this document, the terms and definitions regarding types of heat-treatment in EN 10052:1993, regarding product forms in EN 10079:2007 and the following apply. 3.1 stainless steels steels with at least 10,5 % of chromium and maximum 1,2 % of car

39、bon SOURCE: EN 10020:2000, 3.2.2 Note 1 to entry: Stainless steels are further subdivided in accordance with their main property into corrosion resisting steels, heat resisting steels and creep resisting steels. Note 2 to entry: One type steel in Table 7 in EN 10088-1:2014 and five types of steel in

40、 Table 9 in EN 10088-1:2014 contain less chromium than the minimum defined for stainless steels, but are included in the heat-resisting and creep-resisting steels standards respectively, because they form a part of these two families of steels. 3.2 corrosion resisting steels steels with at least 10,

41、5 % Cr and max. 1,20 % C if their resistance to corrosion is of primary importance 3.3 general purposes purposes other than the special purposes mentioned in the Bibliography 3.4 standard grades grades with a relatively good availability and a wider range of application 3.5 special grades grades for

42、 special use and/or with limited availability 4 Designation and ordering 4.1 Designation of steel grades The steel names and steel numbers (see Tables 1 to 4) were formed in accordance with EN 10027-1 and EN 10027-2 respectively. 4.2 Designation to be used on ordering The complete designation for or

43、dering a product according to this document shall contain the following information: desired quantity; BS EN 10088-2:2014EN 10088-2:2014 (E) 7 product form (strip or sheet/plate); where an appropriate dimensional standard is available (see Annex B) the number of the standard, plus any choice of requ

44、irements; if there is no dimensional standard, the nominal dimensions and tolerances required; type of material (steel); number of this document; steel name or steel number; if for the relevant steel in the table for the mechanical properties more than one treatment condition is covered, the symbol

45、for the desired heat treatment or cold worked condition; desired process route (see symbols in Table 6); if a verification of internal soundness is required, flat products with thickness 6 mm shall be tested in accordance with EN 10307; any additional optional tests or inspections (see 7.2.3 d); sta

46、ndard designation for a test report 2.2 or, if required, any other type of inspection document in accordance with EN 10204 (see 7.2.1). EXAMPLE 10 plates according to EN ISO 18286 with thickness = 8 mm, width = 2000 mm, length = 5 000 mm; tolerances on width and length class B, flatness tolerance cl

47、ass N made of steel EN 100882 with the name X5CrNi1810 and the number 1.4301 in process route 1D (see Table 6), inspection certificate 3.1 as specified in EN 10204: 10 plates EN ISO 18286 , 8 2000 5000 B Steel EN 100882 X5CrNi1810+1D EN 10204 3.1 or 10 plates EN ISO 18286 , 8 2000 5000 B Steel EN 10

48、0882 1.4301+1D EN 10204 3.1 5 Classification of grades Steels covered in this document are classified according to their structure into: austenitic steels, austenitic-ferritic steels, ferritic steels, martensitic steels, precipitation hardening steels. See also EN 10088-1:2014, Annex C. BS EN 10088-

49、2:2014EN 10088-2:2014 (E) 8 6 Requirements 6.1 Steelmaking process Unless a special steelmaking process is agreed at the time of enquiry and order, the steelmaking process for steels conforming to this document shall be at the discretion of the manufacturer. 6.2 Delivery condition The products shall be supplied in the delivery condition agreed at the time of enquiry and order by reference to the process route given in Table 6 and, where different alt