BS EN 10034-1993 Structural steel I and H sections - Tolerances on shape and dimensions《工字型和 H 型结构钢 形状和尺寸公差》.pdf

《BS EN 10034-1993 Structural steel I and H sections - Tolerances on shape and dimensions《工字型和 H 型结构钢 形状和尺寸公差》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10034-1993 Structural steel I and H sections - Tolerances on shape and dimensions《工字型和 H 型结构钢 形状和尺寸公差》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 10034:1993 Structural steel I and H sections Tolerances on shape and dimensions The European Standard EN 10034:1993 has the status of a British Standard UDC 669.14.018.29-423.1:621.753.1BSEN10034:1993 This British Standard, having been prepared under the direction of the Iron

2、and Steel Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 December 1993 BSI 12-1998 The following BSI references relate to the work on this standard: Committee reference ISM/13 Draft for comment 91/38815 DC ISBN 0 580 21968 2 Cooperati

3、ng organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk

4、Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ent

5、e Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i

6、 Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN10034:1993 BSI 12-1998 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN 10034 3 N

7、ational annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back coverBSEN10034:1993 ii BSI 12-1998 National foreword This British Standard has been prepared under the direction of the Iron and Steel Standards Policy Committee and i

8、s the English language version of EN10034:1993, Structural steel I and H sections Tolerances on shape and dimensions, published by the European Committee for Standardization (CEN). This British Standard, together with BS4-1:1993, published simultaneously with this standard, supersedes BS4-1:1980, wh

9、ich is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This d

10、ocument comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside fron

11、t cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10034 September 1993 UDC 669.14.018.29-423.1:621.753.1 Descriptors: Iron and steel products, I beams, structural steels, dimensional tolerances, form tolerances English version Structural steel I and H sections Tolerances on shape and dime

12、nsions Poutrelles I et H en acier de construction Tolerances de formes et de dimensions I- und H-Profile aus Baustahl Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 1993-08-30. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the

13、conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in t

14、hree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of

15、Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat

16、: rue de Stassart 36, B-1050 Brussels 1993 Copyright reserved to CEN members Ref. No. EN 10034:1993 EEN10034:1993 BSI 12-1998 2 Foreword This European Standard has been prepared by ECISS/TC11 Sections: Tolerances and Dimensions; the Secretariat of which is held by BSI. The discussions within ECISS/T

17、C11 were based on Euronorm34-62 Broad flanged beams with parallel sides. Rolling tolerances and Euronorm44-63 Hot rolled IPE joists. Rolling tolerances This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at least by M

18、arch1994, and conflicting national standards shall be withdrawn at the latest by March1994. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,

19、Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Rolling tolerances for structural steel I and H sections 3 5 Tolerance on mass 3 6 Tolerance on length 3 Annex A (informative) Strai

20、ghtness measurement 7 Figure 1 Measurement of length L on I and H steel sections 6 Table 1 Dimensional tolerances for structural steel I and H sections 4 Table 2 Tolerances on out-of-square and web off-centre of structural steel I and H sections 5 Table 3 Tolerances on straightness of structural ste

21、el I and H sections 6EN10034:1993 BSI 12-1998 3 1 Scope This European Standard specifies tolerances on shape dimensions and mass of structural steel I and H sections. These requirements do not apply to I and H sections rolled from stainless steel. These requirements do not apply to taper flange sect

22、ions. NOTEUntil a European Standard for dimensions of I and H beams is published Euronorm19 and Euronorm53 or corresponding national standards may be used. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative re

23、ferences are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references t

24、he latest edition of the publication referred to applies. EN 10079, Definition of steel products. Euronorm 19:1957, IPE beams, parallel flanged beams. Euronorm 53:1962, Wide flange beams with parallel flanges. 3 Definitions For the purpose of this European Standard, the definitions in EN 10079 apply

25、. 4 Rolling tolerances for structural steel I and H sections 4.1 Section height (h) The deviation from nominal on section height measured at the centre line of web thickness shall be within the tolerance given inTable 1. 4.2 Flange width (b) The deviation from nominal on flange width shall be within

26、 the tolerance given inTable 1. 4.3 Web thickness (s) The deviation from nominal on web thickness measured at the mid-point of dimension h shall be within the tolerance given inTable 1. 4.4 Flange thickness (t) The deviation from nominal on flange thickness measured at the quarter flange width point

27、 shall be within the tolerance given inTable 1. 4.5 Out-of-squareness (k + k) The out-of-squareness of the section shall not exceed the maximum given inTable2. 4.6 Web off-centre (e) The mid-thickness of the web shall not deviate from the mid-width position on the flange by more than the distance (e

28、) given inTable2. 4.7 Straightness (q xxor q yy ) The straightness shall comply with the requirements given inTable3. 5 Tolerance on mass The deviation from the nominal mass of a batch or a piece shall not exceed 4.0 %. The mass deviation is the difference between the actual mass of the batch or pie

29、ce and the calculated mass. The calculated mass shall be determined using a density of 7,85 kg/dm 3 . 6 Tolerance on length The sections shall be cut to ordered lengths to tolerances of: a) 50 mm; or b) +100 mm where minimum lengths are requested. L represents the longest useable length of the secti

30、on assuming that the ends of the section have ben cut square (seeFigure1).EN10034:1993 4 BSI 12-1998 Table 1 Dimensional tolerances for structural steel I and H sections Section height h Flange width b Web thickness s Flange thickness t height tolerance width tolerance thickness tolerance thickness

31、tolerance mm mm mm mm mm mm mm mm h 180 b 110 s 700 b 325 20 s 40 2,0 20 t 30 40 s60 2,5 30 t 40 s 60 3,0 40 t 60 t 60 + 3,0 2,0 + 4,0 1,0 + 1,5 0,5 +4,0 2,0 + 4,0 2,0 + 2,0 1,0 + 5,0 3,0 + 4,0 4,0 + 2,5 1,5 + 5,0 5,0 + 6,0 5,0 + 2,5 2,0 + 2,5 2,5 + 3,0 3,0 + 4,0 4,0EN10034:1993 BSI 12-1998 5 Table2

32、 Tolerances on out-of-square and web off-centre of structural steel I and H sections Out-of-square Web off-centre flange width b tolerance flange width b tolerance mm mm mm mm b 110 1,5 Where t 110 2% of b b 110 2,5 (max 6,5 mm) 110 325 5,0 Where t 40 110 325 8,0 kk + e wheree b 1 b 2 2 - =EN10034:1

33、993 6 BSI 12-1998 Table3 Tolerances on straightness of structural steel I and H sections Section height h Tolerance on straightness q xxand q yy on length L mm % 80360 0,1L Figure1 Measurement of length L on I and H steel sectionsEN10034:1993 BSI 12-1998 7 Annex A (informative) Straightness measurem

34、ent Straightness measurement requires a reference straight edge from which deviations in section straightness are measured. A taut string line is an acceptable straight edge provided that deviations in the horizontal plan only are measured. Measurement is carried out as follows: for q xx : The beam

35、is laid in the H position on a flat surface and the string is taken along the outside of the centre of the flange width between the two ends of the unconstrained section. for q yy : The beam is laid in the I position on a flat surface and the string is taken along the flange tip between the two ends

36、 of the unconstrained section.8 blankBSEN10034:1993 BSI 12-1998 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Iron and Steel Standards Policy Committee (ISM/-) to Technical Committee ISM/13 up

37、on which the following bodies were represented: BEAMA Ltd. British Constructional Steelwork Association Ltd. British Steel Industry National Association of Steel Stockholders National annex NB (informative) Cross-references Publication referred to Corresponding British Standard Euronorm19 BS4 Struct

38、ural steel sections Euronorm53 Part1:1993 Specification for hot-rolled sections EN10079:1992 BSEN10079:1993 Definition of steel products BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

39、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and a

40、t the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and

41、services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an

42、 individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In r

43、esponse to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards thr

44、ough its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date wit

45、h standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the

46、 UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without p

47、rior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.