BS EN 915-2008 Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety《体操器材 高低杠 包括安全性的试验方法和要求》.pdf

《BS EN 915-2008 Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety《体操器材 高低杠 包括安全性的试验方法和要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 915-2008 Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety《体操器材 高低杠 包括安全性的试验方法和要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 915:2008ICS 97.220.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDGymnastic equipment Asymmetric bars Requirements andtest methods includingsafetyLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIThis Bri

2、tish Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 July2009. BSI 2009ISBN 978 0 580 58246 2Amendments/corrigenda issued since publicationDate CommentsBS EN 915:2008National forewordThis British Standard is the UK implementation of EN 915:2008. Itsupersed

3、es BS EN 915:1996 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee SW/136/22, Gymnasium and playing field equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to incl

4、ude all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EUROPEAN S

5、TANDARDNORME EUROPENNEEUROPISCHE NORMEN 915November 2008ICS 97.220.30 Supersedes EN 915:1996 English VersionGymnastic equipment - Asymmetric bars - Requirements andtest methods including safetyMatriel de gymnastique - Barres asymtriques - Exigenceset mthodes dessai y compris la scuritTurngerte - Stu

6、fenbarren - Anforderungen undPrfverfahren einschlielich SicherheitThis European Standard was approved by CEN on 27 September 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standar

7、d without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other lang

8、uage made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,

9、France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR

10、 NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 915:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 9

11、15:2008EN 915:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Requirements.4 3.1 Classification4 3.2 Dimensions.4 4 Safety requirements 6 4.1 General requirements6 4.2 Entrapment .6 4.3 Stability .6 4.4 Vertical stiffness and residual deflection6 4.5 Strength 6 4.6 Rigidity o

12、f framework 6 5 Test methods6 5.1 General6 5.2 Determination of stability and rigidity .6 5.2.1 Principle6 5.2.2 Apparatus .7 5.2.3 Test temperature7 5.2.4 Procedure .7 5.2.5 Expression of results 7 5.3 Determination of stiffness and residual deflection7 5.3.1 Principle7 5.3.2 Apparatus .7 5.3.3 Tes

13、t temperature7 5.3.4 Procedure .7 5.3.5 Expression of results 7 5.4 Determination of strength.8 5.4.1 Principle8 5.4.2 Apparatus .8 5.4.3 Test temperature8 5.4.4 Procedure .8 5.4.5 Expression of results 8 6 Instructions for use .8 7 Marking .8 Annex A (informative) Example of a suitable profile and

14、fixing points .9 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 3 Foreword This document (EN 915:2008) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equip

15、ment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention

16、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 915:1996. This European Standard is one of several standards, each

17、of which deals with a particular type or a particular group of gymnastic equipment. The principal changes from the previous edition of EN 915 are as follows: a) the dimensions in Table 2 have been adapted; b) safety requirements and test methods have been modified; c) entrapment has been included; d

18、) requirements and test methods for endurance have been deleted. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin

19、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncon

20、trolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 4 1 Scope This European Standard specifies functional requirements (see Clause 3) and specific safety requirements in addition to the general safety requirements in EN 913 (see Clause 4) which shall be read in conjunction with this standard. This Eu

21、ropean Standard is applicable to 2 types of asymmetric bars (see Table 1) intended for use under supervision of a competent person. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.

22、For undated references, the latest edition of the referenced document (including any amendments) applies. EN 913, Gymnastic equipment General safety requirements and test methods 3 Requirements 3.1 Classification Asymmetric bars shall be classified by the design (types and sizes) as shown in Table 1

23、. Table 1 Types Type Size Description 1 freestanding asymmetric bar without fixing points 2 1 and 2 asymmetric bar with fixing points 3.2 Dimensions All asymmetric bars shall comply with the dimensions specified in Table 2 and Figure 1. The diameter of the bar profile shall be circular (40 1) mm. Li

24、censed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 5 Dimensions in millimetres Key 1 Bar 2 Upright extension 3 Stop, lock and adjustment device 4 Higher upright 5 Lower upright 6 Horizontal adjustment device 7 Base 8 Support

25、ing cup point (Type 1) NOTE Type 2 does not have supporting cup points. The bars are connected to the uprights according to the individual manufacturers design. Figure 1 Asymmetric bars Table 2 Typical dimensions Dimensions in millimetres Minimum range of adjustment Type Size b1b2h1h2h3h4h5 max. 1 1

26、 150 600 2 350 2 100 1 400 1 600 60 1 1 300 600 2 350 2 100 1 400 1 600 60 2 2 1 625 1 025 2 550 2 400 1 600 1 750 10 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 6 4 Safety requirements 4.1 General requirements Asym

27、metric bars shall comply with the requirements of EN 913, except insofar as they are modified by this European Standard. 4.2 Entrapment The entrapment requirements of EN 913 relate to the uprights, horizontal adjustment devices and connections between them as well as bars but excluding the bar conne

28、ctions. 4.3 Stability When tested in accordance with 5.2, equipment shall not tip in any direction when subjected to a horizontal force representing 40 % of the self weight of the equipment with a minimum of 400 N. The force shall be applied at the middle of the upper bar and perpendicular to its le

29、ngth. 4.4 Vertical stiffness and residual deflection When each bar is tested in accordance with 5.3 using a force of 1 350 N 50 N, the deflection of each bar shall be a minimum of 40 mm and a maximum of 100 mm. The residual deflection shall be no greater than 1 mm. 4.5 Strength When each bar is test

30、ed in accordance with 5.4 using a vertical force of 2 850 N 50 N the equipment shall show no signs of fracture, rupture or defects. 4.6 Rigidity of framework For type 1 equipment when tested in accordance with 5.2, the bar at the supporting cup point shall not deflect by more than 20 mm in the longi

31、tudinal or the transverse direction when subjected to horizontal forces of 570 N 20 N in each of these directions. For type 2 equipment when tested in accordance with 5.2, the bar shall not deflect by more than 20 mm at the attachment points in the transverse direction when subjected to a horizontal

32、 force of 570 N 20 N in that direction. Transverse forces shall be applied to the middle of the bar and perpendicular to its length. Longitudinal forces shall be applied along the axis of the bar. 5 Test methods 5.1 General All loading tests shall be carried out with the bars set at their maximum us

33、eful heights. 5.2 Determination of stability and rigidity 5.2.1 Principle A horizontal force is applied to the equipment in the specified manner. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 7 5.2.2 Apparatus A strap

34、 (100 1) mm wide. 5.2.3 Test temperature Condition the equipment for a minimum of 3 h at a test temperature of (23 2) C. 5.2.4 Procedure Block freestanding equipment (type 1) on the ground to avoid the sliding. Apply the specified horizontal force for a period of 65 s 5 s. Note any tipping of the eq

35、uipment. When required, measure the deflection of the bar supporting cup in the direction of the applied force. 5.2.5 Expression of results Report whether tipping has occurred. When required, report the deflection of the bar supporting cup in millimetres. 5.3 Determination of stiffness and residual

36、deflection 5.3.1 Principle A vertical force is applied to the centre of each bar and any deflection is measured. The force is then removed and any residual deflection is measured. 5.3.2 Apparatus A strap (100 1) mm wide. 5.3.3 Test temperature Condition the equipment for a minimum of 3 h at a test t

37、emperature of (23 2)C. 5.3.4 Procedure Apply a vertical force at the centre of the bar for 65 s 5 s. Measure the position of the loaded component from any convenient datum point. Record the deflection at the centre of the bar. Remove the force. Measure the residual deflection 30 min 10+min after rem

38、oval of the force. Record any residual deflection. 5.3.5 Expression of results Express stiffness as the deflection under load in millimetres. Express the residual deflection as the deflection in millimetres remaining 30 min 10+min after the removal of the load. Licensed Copy: Wang Bin, ISO/EXCHANGE

39、CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 8 5.4 Determination of strength 5.4.1 Principle The equipment is loaded with a vertical force and examined for fracture or other damage. 5.4.2 Apparatus A strap (100 1) mm wide. 5.4.3 Test temperature Conditio

40、n the equipment for a minimum of 3 h at a test temperature of (232)C. 5.4.4 Procedure Apply a vertical force at the centre of the bar for 65 s 5 s. Note any fracture, rupture, defects or other damage to the equipment. 5.4.5 Expression of results Express the strength by whether fracture or other dama

41、ge has occurred. 6 Instructions for use An information booklet shall be provided by the manufacturers containing the following: a) installation details; b) assembly details covering method of adjustment; c) equipment space; d) self weight of the equipment; e) maintenance details; f) warning notice t

42、hat the equipment should be used under controlled supervision. 7 Marking Marking shall comply with EN 913. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008EN 915:2008 (E) 9 Annex A (informative) Example of a suitable profile and fixing

43、 points Dimensions in millimetres Figure A.1 Type 2 with its fixing points Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 13/10/2009 04:14, Uncontrolled Copy, (c) BSIBS EN 915:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - Briti

44、sh Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British

45、Standards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technic

46、al committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standards

47、Orders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international stan

48、dards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to Ex

49、portersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Te