BS EN 683-3-2006 Aluminium and aluminium alloys - Finstock - Part 3 Tolerances on dimensions and form《铝和铝合金 散热片坯料 第3部分 尺寸和形状公差》.pdf

《BS EN 683-3-2006 Aluminium and aluminium alloys - Finstock - Part 3 Tolerances on dimensions and form《铝和铝合金 散热片坯料 第3部分 尺寸和形状公差》.pdf》由会员分享，可在线阅读，更多相关《BS EN 683-3-2006 Aluminium and aluminium alloys - Finstock - Part 3 Tolerances on dimensions and form《铝和铝合金 散热片坯料 第3部分 尺寸和形状公差》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 683-3:2006Aluminium and aluminium alloys Finstock Part 3: Tolerances on dimensions and formThe European Standard EN 683-3:2006 has the status of a British StandardICS 77.150.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g5

2、9g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 683-3:2006This British Standard was published under the authority of the Standards Policy and Strategy Co

3、mmittee on 28 February 2007 BSI 2007ISBN 978 0 580 50130 2National forewordThis British Standard was published by BSI. It is the UK implementation of EN 683-3:2006. It supersedes BS EN 683-3:1997 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/35,

4、Light metals and their alloys.A list of organizations represented on NFE/35 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot

5、 confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 683-3December 2006ICS 77.150.10 Supersedes EN 683-3:1996 Engl

6、ish VersionAluminium and aluminium alloys - Finstock - Part 3: Toleranceson dimensions and formAluminium et alliages daluminium - Bandes pourchangeurs thermiques - Partie 3 : Tolrances surdimensions et formeAluminium und Aluminiumlegierungen - Vormaterial frWrmeaustauscher (Finstock) - Teil 3: Grenz

7、abmae undFormtoleranzenThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists a

8、nd bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibili

9、ty of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy,

10、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brus

11、sels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 683-3:2006: ELicensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-3:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative refer

12、ences 4 3 Tolerances on dimensions and form.4 3.1 Gauge4 3.2 Width .5 3.3 Lateral bow .6 Tables Table 1 Tolerances on average gauge for finstock 5 Table 2 Density.5 Table 3 Tolerance on width for finstock 6 Table 4 Maximum value of lateral bow.7 Figures Figure 1 Measurement of lateral bow: method a)

13、 .6 Figure 2 Measurement of lateral bow: method b).7 Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-3:2006 (E) 3 Foreword This document (EN 683-3:2006) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secreta

14、riat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. This document supersede

15、s EN 683-3:1996. Within its program of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 6 “Foil and finstock“ to revise EN 683-3:1996. The following modifications have been made: subclause 3.1.1: the text has been amended; subclause 3.1.2: title is changed alloys EN AW-6060 and EN AW-695

16、1 have been deleted in Table 2; subclause 3.3: lateral bow is applicable to thickness greater than 130 m. Test procedures have been amended and acceptance criteria have been edited. EN 683 comprises the following parts under the general title “Aluminium and aluminium alloys Finstock“: Part 1: Techni

17、cal conditions for inspection and delivery Part 2: Mechanical properties Part 3: Tolerances on dimensions and form Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such p

18、atent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal

19、 Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan

20、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-3:2006 (E) 4 1 Scope This document specifies the tolerances on dimensions and form for wrought a

21、luminium and wrought aluminium alloy finstock supplied in accordance with EN 683-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of th

22、e referenced document (including any amendments) applies. Not applicable 3 Tolerances on dimensions and form 3.1 Gauge 3.1.1 Single gauge measurement The tolerance on gauge for a single measurement for finstock shall be 6 %. Gauge can be measured with any of the usual precision instruments capable o

23、f assessing finstock thickness but, in the event of a dispute, the weighing method shall be used as a referee procedure. Description of the weighing method: From the test sample, cut an area (A) of approximately 1 dm2either square or circular. Degrease the sample if necessary in a suitable solvent a

24、nd weigh on a laboratory balance with an accuracy of equal to or better than 1 mg. The dimensions of the sample (sides of square or diameter of circle) shall be measured to an accuracy of equal or better than 0,1 mm. Gauge shall be calculated by use of the formula: DAME=10where: E is the gauge in mi

25、crometres; M is the mass in milligrams; D is the density as defined in Table 2, in grams per cubic centimetre; A is the area in square decimetres. 3.1.2 Average gauge evaluation The tolerance on average gauge is specified in Table 1. Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, U

26、ncontrolled Copy, (c) BSIEN 683-3:2006 (E) 5 Table 1 Tolerances on average gauge for finstock Lot size kg Tolerance % 3 000 5 3 000 to 10 000 4 10 000 3 Average gauge may be obtained by either: a) Calculation Calculation of average gauge by this method requires an accurate knowledge of length and ne

27、t weight of the reels. The mean gauge shall be calculated by the formula: DWLPEm=610where: Emis the average gauge in micrometres; P is the net mass in kilograms; L is the length in metres; W is the width in millimetres; D is the density as defined in Table 2, in grams per cubic centimetres. Table 2

28、Density Density Material g/cm3EN AW-1050A 2,70 EN AW-1100 2,71 EN AW-1200 2,71 EN AW-3003 2,73 EN AW-3103 2,73 EN AW-5005 2,69 EN AW-6063 2,70 EN AW-8006 2,74 EN AW-8011A 2,71 EN AW-8079 2,71 b) Averaging spot measurements The method shall be agreed between purchaser and supplier. 3.2 Width The tole

29、rance on width is specified in Table 3. Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-3:2006 (E) 6 Table 3 Tolerance on width for finstock Dimensions in millimetres Width Toleranceover up to Symmetrical Only plus Only minus - 100 0,2 4,0 0 +0 4,0 -

30、 100 350 0,3 6,0 0 +0 6,0 - 350 1 000 0,5 0,1 0 +0 ,01 - 1 000 - 1,0 0,2 0 +0 ,02 - Unless otherwise specified in the order, the type of tolerance is at the discretion of the supplier. 3.3 Lateral bow 3.3.1 Test procedure Lateral bow shall be measured on finstock with a width greater than 100 mm and

31、 a thickness greater than 130 m; on narrow width finstock (width up to 100 mm), this measurement shall be carried out only if required by the purchaser. One of the following test procedures shall be used. a) Take a sample from the first set of slit reels produced from the parent coil. Cut one 2 000

32、mm length from that sample. Measure the lateral bow called a against a straight edge as shown on Figure 1 on length of 2 000 mm. Dimensions in millimetres Figure 1 Measurement of lateral bow: method a) b) Take a sample from the first set of slit reels produced from the parent coil. Cut two 1 000 mm

33、lengths from that sample. Place the two lengths back to back on a flat surface. Measure the maximum distance called b between the two lengths as shown in Figure 2. Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-3:2006 (E) 7 Dimensions in millimetres

34、 Key 1 Side edges Figure 2 Measurement of lateral bow: method b) 3.3.2 Test results The lateral bow is defined as the distance a according to method a. The lateral bow is defined as the distance b according to method b 3.3.3 Acceptance criteria The maximal lateral bow shall not exceed a certain valu

35、e as given in Table 4. Table 4 Maximum value of lateral bow Dimensions in millimetres Method a Method b Width a for 2 000 b for 1 000 over up to max. max. 100 300 8 16 300 500 6 12 500 1 000 5 10 1 000 - 4 8 Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIE

36、N 683-3:2006 (E) 8 Bibliography 1 EN 683-1, Aluminium and aluminium alloys - Finstock - Part 1: Technical conditions for inspection and delivery Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSIblankLicensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00

37、2007, Uncontrolled Copy, (c) BSIBS EN 683-3:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by

38、 Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an

39、 inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS

40、 which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are a

41、lso available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of informatio

42、n on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44

43、(0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7

44、001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, i

45、n the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise with

46、out prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.Licensed Copy: Wang Bin, na, Wed Apr 04 07:26:51 GMT+00:00 2007, Uncontrolled Copy, (c) BSI