BS EN 683-1-2006 Aluminium and aluminium alloys Finstock Part 1 Technical conditions for inspection and delivery《铝和铝合金 叶片坯料 第1部分 检验和交付技术条件》.pdf

《BS EN 683-1-2006 Aluminium and aluminium alloys Finstock Part 1 Technical conditions for inspection and delivery《铝和铝合金 叶片坯料 第1部分 检验和交付技术条件》.pdf》由会员分享，可在线阅读，更多相关《BS EN 683-1-2006 Aluminium and aluminium alloys Finstock Part 1 Technical conditions for inspection and delivery《铝和铝合金 叶片坯料 第1部分 检验和交付技术条件》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 683-1:2006Aluminium and aluminium alloys Finstock Part 1: Technical conditions for inspection and deliveryThe European Standard EN 683-1:2006 has the status of a British StandardICS 77.150.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g

2、44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 683-1:2006This British Standard was published under the authority of the Standards Policy

3、and Strategy Committee on 28 February 2007 BSI 2007ISBN 978 0 580 50132 6National forewordThis British Standard was published by BSI. It is the UK implementation of EN 683-1:2006. It supersedes BS EN 683-1:1996 which is withdrawn.The UK participation in its preparation was entrusted to Technical Com

4、mittee NFE/35, Light metals and their alloys.A list of organizations represented on NFE/35 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British

5、Standard cannot confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 683-1December 2006ICS 77.150.10 Supersedes EN

6、683-1:1996 English VersionAluminium and aluminium alloys - Finstock - Part 1: Technicalconditions for inspection and deliveryAluminium et alliages daluminium - Bandes pourchangeurs thermiques - Partie 1 : Conditions techniquesde contrle et de livraisonAluminium und Aluminiumlegierungen - Vormaterial

7、 frWrmeaustauscher (Finstock) - Teil 1: TechnischeLieferbedingungenThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standar

8、d without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other langua

9、ge made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,German

10、y, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManage

11、ment Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 683-1:2006: ELicensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-1:2006 (E) 2 Content

12、s Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Ordering information.4 5 Requirements.5 5.1 Production and manufacturing processes .5 5.2 Quality control5 5.3 Chemical composition 6 5.4 Mechanical properties.6 5.5 Freedom from defects .6 5.6 Tolerances on dimensions

13、and form.6 5.7 Special properties6 6 Test procedure.6 6.1 Sampling.6 6.2 Methods of testing.7 6.3 Retests 8 7 Inspection documents.8 8 Marking of products 8 9 Packaging .9 10 Complaints of non-conformity .9 Bibliography 10 Licensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled

14、 Copy, (c) BSIEN 683-1:2006 (E) 3 Foreword This document (EN 683-1:2006) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of

15、an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. This document supersedes EN 683-1:1996. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 6 “Foil and finstock“ to rev

16、ise EN 683-1:1996. The following modifications have been made: scope is changed into gauge ranges from 60 m to 400 m; Clause 3 refers now to EN 12258-1; Clause 4: title is changed, and list is amended; Clause 5: subclause 5.2 is modified; Clause 6: subclauses 6.1.1 and 6.2.1 are modified; Clause 7:

17、completely ammended; addition of Bibliography. EN 683 comprises the following parts under the general title “Aluminium and aluminium alloys Finstock“: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Tolerances on dimensions and form Attention is drawn t

18、o the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard p

19、roducts under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, B

20、elgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na,

21、Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-1:2006 (E) 4 1 Scope This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy finstock. The gauge range covered is 60 m to 400 m. It does not apply to cladded fin

22、stock. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium a

23、nd aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition EN 683-2, Aluminium and aluminium alloys Finstock Part 2: Mechanical properties EN 683-3, Aluminium and aluminium alloys Fi

24、nstock Part 3: Tolerances on dimensions and form EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 14242, Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission spectral analysis EN 14361, Aluminium and aluminium

25、alloys - Chemical analysis - Sampling from metal melts 3 Terms and definitions For the purposes of this document, the terms and definitions of EN 12258-1:1998 and the following applies. 3.1 finstock flat, cold rolled product of rectangular cross section and thickness in the range 60 m to 400 m suita

26、ble for heat exchanger applications 4 Ordering information The order shall specify the product required and shall contain the following information: a) type and form of product: the designation of the aluminium or aluminium alloy; the form of the product; b) temper designation of the material to be

27、delivered as specified in EN 515; c) number of this European Standard (EN 683-1) or separate specification, if any; Licensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-1:2006 (E) 5 d) dimensions of the product: thickness; width and type of specified tole

28、rance on width as defined in EN 683-3 (symmetrical, only plus, only minus), or as agreed between supplier and purchaser; internal and external diameter of the coil/reel; core size and type; e) quantity (mass); f) any special requirements agreed between supplier and purchaser, e.g.: test certificates

29、 and inspection reports; marking of the products, e.g. identification; reference to drawings, e.g. for packaging, coil axis orientation, etc.; whether surface degreasing is required. Where special requirements are specified, the application shall be stated. 5 Requirements 5.1 Production and manufact

30、uring processes Unless otherwise specified in the order, the production and manufacturing processes shall be left to the discretion of the supplier. Unless it is explicitly stated in the order, no obligation shall be placed on the supplier to use the same processes for subsequent and similar orders.

31、 5.2 Quality control The manufacturer shall establish and maintain a quality management system, which should be at least equivalent to EN ISO 9001. The manufacturer shall establish and maintain inspection plans defining all inspections and tests to be performed on the product to fulfil the requireme

32、nts of this standard and any other requirement agreed according to Clause 6 of the present standard, their frequency and the type of record to be established. The inspection plan shall specify for each inspection or test whether it is to be performed per cast, per heat treatment batch, per inspectio

33、n lot as defined in EN 12258-1 or per any other lot of importance. The inspection plan shall conform as a minimum to the test procedures and test requirements stipulated in this standard. The inspection plan shall include additional schemes for appropriate process control. If required the inspection

34、 plan shall be submitted to the purchaser for approval before start of production. The manufacturer shall be responsible for carrying out all inspections and tests required by this standard, prior to the shipment of the product. If the purchaser wishes to inspect the product at the manufacturers sit

35、e of production, he shall stipulate this at the time of placing the order. The extent of inspections shall be in accordance with Clause 6 of the present standard. Unless explicitly stated quality controls and inspections shall be performed on inspection lots. Products included in one inspection lot

36、shall be manufactured in the same production unit. Licensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-1:2006 (E) 6 5.3 Chemical composition The chemical composition shall be in conformity with the requirements specified in EN 573-3, unless otherwise agr

37、eed between supplier and purchaser. 5.4 Mechanical properties The mechanical properties shall be in conformity with EN 683-2, unless otherwise agreed between supplier and purchaser. 5.5 Freedom from defects The product shall be free from defects prejudicial to its suitable and proper use. 5.6 Tolera

38、nces on dimensions and form The tolerances on dimensions and form shall be in conformity with EN 683-3. 5.7 Special properties Any special property requirements shall be agreed between purchaser and supplier. 6 Test procedure 6.1 Sampling 6.1.1 Samples for chemical analysis Sampling shall be carried

39、 out at the time of casting according to EN 14361. The average content of each sample shall be within the specification for the chemical composition. NOTE EN 14361 includes criteria how to determine number, volume and shape of samples, about time and location of sampling and about the design and mai

40、ntenance of the tools, in order to make sure that the average chemical composition of the sample is representative of the average chemical composition of the whole melt. 6.1.2 Specimens for mechanical testing 6.1.2.1 Location and size Specimens shall be taken from samples in such a way that it is po

41、ssible to orientate the test pieces in relation to the product, as specified in 6.1.2.2. The specimens shall be large enough to allow manufacture of the test pieces necessary to carry out the required tests and shall include sufficient metal to allow manufacture of test pieces for any retests requir

42、ed. 6.1.2.2 Orientation Specimens shall be taken in such a manner that the test pieces can be prepared in the longitudinal direction. 6.1.2.3 Identification Each specimen shall be identified in such a way that after removal, it is still possible to identify the product from which it was taken and it

43、s location and orientation. If during the course of subsequent operations removal of the markings cannot be avoided, new markings shall be made before the originals are removed. Licensed Copy: Wang Bin, na, Thu Aug 09 02:45:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 683-1:2006 (E) 7 6.1.2.4 Pre

44、paration Specimens shall be taken from the sample after completion of all the mechanical and heat treatment operations that the product has to undergo before delivery and which can influence the mechanical properties of the metal. In cases where this is not possible, the sample or specimens may be t

45、aken at an earlier stage, but they shall be subjected to the same treatment as that to which it is intended to submit the product concerned. Cutting shall be carried out in such a manner that it does not change the characteristics of the part of the specimen from which the test pieces are to be prep

46、ared. Thus, the dimensions of the specimens shall provide an adequate allowance to permit removal of the zone affected by cutting. Specimens shall not be treated in any way that alters their mechanical properties. 6.1.2.5 Number One specimen shall be taken from each inspection lot of 10 000 kg or pa

47、rt thereof. For single coils weighing more than 10 000 kg each, only one specimen per coil shall be taken. 6.1.3 Test pieces for tensile test 6.1.3.1 Identification Each test piece shall be marked in such a manner that it is possible to identify the inspection lot from which it was taken and, if req

48、uired, its location and orientation in the product. If a test piece is identified by stamping, this shall not be in a place or manner which can interfere with subsequent testing. Where it is not convenient to mark a test piece, an identification tag may be attached. 6.1.3.2 Number One test piece sha

49、ll be taken from each specimen. 6.1.3.3 Type Flat test pieces shall be used for all thicknesses covered by EN 683-2. The test piece shall be prepared so that both rolled surfaces are included undisturbed. 6.1.3.4 Machining Any machining necessary shall be carried out in such a manner that it does not change the characteristics of the metal in the test piece. 6.2 Methods of testing 6.2.1 Analysis of chemical composition The ranges of application and the accuracy of the test procedure used shall be validated