BS EN 664-1995 Resilient floor coverings Determination of volatile loss《弹性地板覆盖物 挥发损失的测定》.pdf

《BS EN 664-1995 Resilient floor coverings Determination of volatile loss《弹性地板覆盖物 挥发损失的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 664-1995 Resilient floor coverings Determination of volatile loss《弹性地板覆盖物 挥发损失的测定》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、CEN EN*bb4 9Y = 3404587 0083178 631 Resilient floor coverings - Determination of volatile loss The European Standard EN 664 : 1994 has the status of a British Standard BS EN 664: 1995 I .- I. . Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo re

2、production or networking permitted without license from IHS-,-CEN EN*bb4 94 3404589 OOd31fl 578 H BS EN 664 : 1995 direction of the Building and Civil Engineering Sector Board (B/-), was published under the authority of the Standards Board and comes into effect on 15 February 1996 O BSI 1995 The fol

3、lowing BSI references relate to the work on this standard: Committee reference PRY60 Draft for comment 92/38638 DC BBN O 680 23249 2 Amd. No. Cooperating organizations Date Qxt affected F The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, c

4、omprises the national standards organizations of the following countries: Austria Belgium Denmark Finland France Germany Greece Iceland Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom Oesterreichisches Normungsinstitut Institut belge de normalisation Dans

5、k Standard Suomen Standardisoimisliito, KY, Association franaise de normalisation Deutsches Institut fr Normung e.V. Hellenic Organization for Standardization Tkchnological Institute of Iceland National Standards Authority of Ireland Ente Nazionale Italiano di Unificazione Inspection du Travail et d

6、es Mines Nederlands Noimalisatie-instituut Norges Standardiseringsforbund Instituto Portugus da Qualidade Asociacin Espaola de Normalizacin y Certificacin Standardiseringskommissionen i Sverige Association suisse de normalisation British Standards Institution Copyright European Committee for Standar

7、dization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-BS EN 664 : 1995 Contents Cooperating organizations Nat.iona1 foreword Page Inside front cover i Foreword 2 Text of EN 664 3 National annex NA (informative) Committees resp

8、onsible Inside back cover National foreword This British Standard has been prepared by %chnical Conunittee PRI/GO, Resilient floor coverings, and is the English language version of EN 664 : 1994 Resilient floor coverirzgs - Detei-)izirzc;ltion of vokctile loss, published by the European Committee fo

9、r Standardization (CEN). Compliance with a British Standard does not of itself confer immunity from legal obligations. i Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-CEN EN*bb4

10、94 3404589 0083281 126 EUROPEAN STANDARD EN 664 NORME EUROPENNE EUROPISCHE NORM November 1994 ICs 91.180 Descriptors: Floor coverings, tests, determination, weight losses, weight losses on heating, volatile matter English version Resilient floor coverings - Determination of volatile loss Revtements

11、de sol rsilients - Dtermination de la perte de matires volatiles Elastische Bodenbelge - Bestimmung des Verlustes an flchtigen Bestandteilen This European Standard was approved by CEN on 1994-11-10. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditio

12、ns for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three off

13、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria,

14、 Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de

15、 Stassart 36, B-1050 Brussels O 1994 Copyright reserved to CEN members Ref. No. EN 664 : 1994 E Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-CEN ENxbb4 94 = 3404589 0083182 Ob2

16、Page 2 EN 664 : 1994 Foreword This European Standard was prepared by %chnical Committee CEN/TC 134, Resilient and textile floor coverings, the secretariat of which is held by BSI. This European Standard shal be given the status of a national standard, either by publication of an identical text or by

17、 endorsement, at the latest by May 1995, and conflicting national standards shall be withdrawn at the latest by May 1995. According to the CENCENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Gree

18、ce, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-1 Scope This

19、European Standard specifies a method for determining the volatile loss in mass of polyvinyl chloride floor coverings. 2 Principle The percentage loss of mass of a test piece taken from the suiface layer of a material during a specified heat treatment in the presence of an absorbent mateiial is measu

20、red. 3 Apparatus and materials at (100 f 2) OC. 3.1 A eizti2ttc.d men, capable of being maintained Page 3 EN 664 : 1994 6 Procedure Weigh each test piece separately and record the mass. Place the test piece in a metal dish. Csing new charcoal for each test, pour approximately 120 O00 min3 of activat

21、ed charcoal into the bottom of the container. Place the dish on the charcoal and cover with a further 120 000 MIT? of charcoal. Repeat this procedure for the two other test pieces, then place the perforated cover on the container. Place the container in the oven which has previously been brought up

22、to a temperature of 100 OC. Six hours later: remove the test pieces, leave them to cool for 24 h in the standard atmosphere and then weigh them again. 3.2 A metal coiztctitzeii; of volume approximately 900 O00 min3. with nerforatecl cover. 7 Calculation and expression of results 3.3 Metal mesh cimul

23、m clisiws, with approximately 1 hole per min2; diameter 60 mm, height approximately 6 mm. 3.4 Activated chwcoctl, free of powder, grain size (4 to 6) min, of uniform type and quality. The charcoal, sieved and dried at 70 OC (preferably in a vacuum) to a constant niass, shall be kept in a hermeticall

24、y sealed container. 3.5 A balatzm with a sensitivity of 1 mg. 4 Sampling and preparation of test pieces Pake a representative sample from the available material. Pake three test pieces peeled or cut from the surface layer of the sample, the distance between the outer edge of the sample and the neare

25、st edge of the test pieces being at least 100 mm, of minimum area 2000 mm2. 5 Conditioning Condition the test pieces at a temperature of (23 f 2) OC and relative humidity of (50 f 5) % for a minimum of 24 h. Maintain these conditions when carrying out the test. Express the change in mass loss as a p

26、ercentage of the original mass for each test piece. Calculate the mean value for volatile loss for the three test pieces. 8 Test report The test report shall include the following information: a) a reference to this standard, i.e. EN 664; b) a complete identification of the product tested, including

27、 type, source, manufacturers reference nuinbeis; e) the previous histoiy of the sample; d) the mean valiie for volatile loss; e) any deviation from this standard which may have affected the results. Copyright European Committee for Standardization Provided by IHS under license with CENNot for Resale

28、No reproduction or networking permitted without license from IHS-,- CEN EN*bb4 94 W 3404589 0083184 935 BS EN 664 : 1995 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted to Technical Committee PRI/GO, R

29、esilient floor coverings, upon which the following bodies were represented: British Adhesive and Sealants Association British Floor Covering Manufacturers Association British Railways Board British Rubber Manufacturers Association Ltd. Consumer Policy Committee of BSI Contract Flooring Association C

30、ork Industry Federation Department of the Environment (British Board of Agrment) Department of the Environment (Building Research Establishment) Federation of Plastering and Drywall Contractors Institute of Chartered Arbitrators Royal Institute of British Architects Wood Panel Products Federation Co

31、opted members Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-CEN EN*bb4 94 = 3404589 0083185 871 BS EN 664 : 1995 BSI 389 Chiswick High Road London W4 4AL 9502- 3- 0.5k- JWD BSI -

32、 British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include al

33、l the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. Any person who finds

34、an inaccuracy or ambiguity while using this British Standard should bring it to the attention of the Quality Manager, BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive t

35、he latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick: Tel: 0181 996 7000; Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy t

36、o supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information

37、Echnology Service (BITS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick: Tel: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standard

38、s. For details of these and other benefits contact Customer Services, Membership at Chiswick: El: 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in ail BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude t

39、he free use, in the course of implementing the standard of necessary details such as symbols and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any

40、 other form whatsoever, the permission in writing of BSI must be obtained and if granted will be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager at Chiswick. ISBN O 580 23249 2 PRI/GO Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-