BS EN 6049-003-2009 Aerospace series - Electrical cables installation - Protection sleeve in meta-aramid fibres - Braided tubular expandable - Product standard《航空航天系列 安装电缆 间聚芳族酰胺纤维.pdf

《BS EN 6049-003-2009 Aerospace series - Electrical cables installation - Protection sleeve in meta-aramid fibres - Braided tubular expandable - Product standard《航空航天系列 安装电缆 间聚芳族酰胺纤维.pdf》由会员分享，可在线阅读，更多相关《BS EN 6049-003-2009 Aerospace series - Electrical cables installation - Protection sleeve in meta-aramid fibres - Braided tubular expandable - Product standard《航空航天系列 安装电缆 间聚芳族酰胺纤维.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 6049-003:2009ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Electrical cables, installation Protection sleeve in meta-aramid fibresPart 003: Braided, tubular, expandable Product standardThis British Standard was published under

2、the authority of the Standards Policy and Strategy Committee on 31 December 2009 BSI 2009ISBN 978 0 580 67328 3Amendments/corrigenda issued since publicationDate CommentsBS EN 6049-003:2009National forewordThis British Standard is the UK implementation of EN 6049-003:2009. The UK participation in it

3、s preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Use

4、rs are responsible for its correct application. Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 6049-003:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6049-003 August 2009 ICS 49.060 English Version Aerospace series - Electrical cables, installation -

5、 Protection sleeve in meta-aramid fibres - Part 003: Braided, tubular, expandable - Product standard Srie arospatiale - Cbles lectriques, installation - Gaine de protection en fibres mta-aramides - Partie 003: Tresse, tubulaire, expansible - Norme de produit Luft- und Raumfahrt - Elektrische Leitung

6、en, Installation - Schutzschlauche aus Meta-Aramidfasern - Teil 003: Geflecht, rohrenformig, dehnbar - Produkt Norm This European Standard was approved by CEN on 20 June 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

7、opean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (Engl

8、ish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria

9、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZAT

10、ION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6049-003:2009: EBS EN 6049-003:2009EN 6049-003:2009 (E) 2 C

11、ontents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Characteristics .4 5 Test methods 6 6 Designation 7 7 Marking .7 BS EN 6049-003:2009EN 6049-003:2009 (E) 3 Foreword This document (EN 6049-003:2009) has been prepared by the Aerospace and Defence Industries Assoc

12、iation of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This

13、 European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2010, and conflicting national standards shall be withdrawn at the latest by February 2010. Attention is drawn to the possibility that some of

14、the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement

15、 this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and

16、the United Kingdom. BS EN 6049-003:2009EN 6049-003:2009 (E) 4 1 Scope This standard defines the characteristics of tubular braided expandable mechanical protection sleeves for electrical cable and cable bundles made from Meta-aramid fibres and provided with a water repelled protection. 2 Normative r

17、eferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3475-601, Aerospace series Cables, e

18、lectrical, aircraft use Test methods Part 601: Smoke density. EN 3475-602, Aerospace series Cables, electrical, aircraft use Test methods Part 602: Toxicity. EN 6049-001, Aerospace series Electrical cables, installation Protection sleeve in meta-aramid fibres Part 001: Technical specification. 2)EN

19、6059-100 1), Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General. 2)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 6049-001 apply. 4 Characteristics 4.1 Composition, dimensions and mass 4.1.1 Composition

20、 of the tows Each tow shall be built-up of several groups of multifilament fibres made from Meta-aramid. The number of groups which forms a tow and the width of the tow depends on the braiding configuration (braiding Figure 1 and braiding angle) of the sleeve, see 4.1.2. The thickness of the tow sha

21、ll be so that the finished sleeve meet the mechanical and environmental requirements. One length of sleeve shall be built-up of one type of tow. 4.1.2 Composition, dimensions and mass of the sleeve The composition of the sleeve (braiding Figure 1, braiding angle and tow width) shall be so that the s

22、leeve meet the requirements for dimensions, coverage, expansion range and mass. The coverage shall be 80 % minimum. The braiding Figure 1 shall consist of two groups of tows in two directions. The braiding angle between the two groups shall be equal over the length of the sleeve. The maximum differe

23、nce measured on a mandrel with the delivered diameter in accordance with EN 6059-202 is 3 %. Figure 2 and Table 2 give the composition and the dimensions of the sleeve. 1) All parts quoted in this document. 2) Published as ASD Prestandard at the date of publication of this standard. BS EN 6049-003:2

24、009EN 6049-003:2009 (E) 5 Braiding pattern Key 1 Pitch 2 One tow d = Inner diameter Figure 1 Composition of the sleeve Table 1 Dimensions and mass Size code d Mass Delivered min. max. Nominal a max. b mm mm mm mm g/m 02 1 1 2 2 3 04 2 2 4 4 4 06 4 4 8 6 8,5 08 6 6 12 8 11,5 10 8 8 16 10 14 15 10 10

25、20 15 17,5 20 12 12 24 20 22 25 15 15 30 25 32,5 30 20 20 40 30 39,5 aIn practice approximately the maximum diameter of a cable bundle. bAt the delivered diameter. BS EN 6049-003:2009EN 6049-003:2009 (E) 6 4.2 Color and materials 4.2.1 Color Color shall be olive green, code 5 (preferential), or ivor

26、y, code 9. 4.2.2 Materials The materials shall be multifilament fibres of Meta-aramid and meet the requirements as specified in this standard. 4.3 Mechanical properties 4.3.1 Sun light exposure After testing according to EN 6059-301 for 40 hours, the retention of the tensile strength shall be 45 % m

27、inimum with respect to the determined values of non-tested tows. 4.3.2 Temperature range The operation temperature of the protection sleeves shall be: a) Maximum: 240 C; b) Minimum: 55 C. NOTE Above 175 C: loss of water repellent properties. 4.3.3 Resistance to fluids range After testing according t

28、o EN 6059-303, the retention of the tensile strength shall be 90 % minimum with respect to the determined values of non-tested tows. 4.3.4 Water absorption To fulfil the requirements for water absorption, the sleeve shall repel water as tested in EN 6059-305 for 6 hours. This test shall be executed

29、after a high temperature exposure test according to EN 6059-302 at 175 C. 4.3.5 Mould growth After testing according to EN 6059-306, there shall no external deterioration which would affect service use and no mould growth visible to the naked eye. 4.3.6 Tensile strength of tows The tensile force to

30、be applied per dTEX shall not be less than 0,03 N. Degradation of the tensile strength after environmental tests shall be within the limits as mentioned in the relevant paragraph. For this test, unbraided tows of the batch which have been used for braiding of the sleeves may be used. 5 Test methods

31、The tests shall be carried out as shown in Table 2. For the number of samples, see EN 6049-001. BS EN 6049-003:2009EN 6049-003:2009 (E) 7 Table 2 Test methods and sanctions Test methods Title Remarks EN 6059-201 Visual examination See 4.1 and 4.2.1. EN 6059-202 Dimensions and mass See 4.1.2. EN 6059

32、-203 Coverage See 4.1.2. EN 6059-301 Sun light exposure See 4.3.1. EN 6059-302 High temperature exposure At maximum operating temperature (continue). See 4.3.2. EN 6059-303 Resistance to fluids See 4.3.3. EN 6059-304 Flammability EN 6059-305 Fluid absorption See 4.3.4. EN 6059-306 Mould growth See 4

33、.3.5. EN 6059-401 Expansion range See 4.1.2. EN 6059-402 Bending properties Not applicable EN 6059-403 Scrape abrasion Needle load shall be 10 N EN 6059-404 Tensile strength See 4.3.6. EN 6059-405 Dynamic cut through Load shall be 30 N EN 3475-601 Smoke density EN 3475-602 Toxicity 6 Designation EXA

34、MPLE Description block BRAIDED, TUBULAR, EXPANDABLE Identity block EN6049-003-02-5 Number of this standard Size code (see Table 1) Color code NOTE 1 If necessary, the code I9005 may be placed between the description block and the identity block. 7 Marking For the marking of the packaging, see EN 604

35、9-001. BS EN6049-003:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at thei

36、nternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We

37、would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an indi

38、vidual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Ema

39、il: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsB

40、SI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:

41、+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +

42、44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the pu

43、blications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermi

44、ssion from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: