BS EN 4071-2009 Aerospace series - Bolts normal hexagonal head close tolerance normal shank short thread in titanium alloy aluminium IVD coated - Classification 1100 MPa (at ambien.pdf

《BS EN 4071-2009 Aerospace series - Bolts normal hexagonal head close tolerance normal shank short thread in titanium alloy aluminium IVD coated - Classification 1100 MPa (at ambien.pdf》由会员分享，可在线阅读，更多相关《BS EN 4071-2009 Aerospace series - Bolts normal hexagonal head close tolerance normal shank short thread in titanium alloy aluminium IVD coated - Classification 1100 MPa (at ambien.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 4071:2009ICS 49.030.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Bolts, normalhexagonal head, closetolerance normalshank, short thread,in titanium alloy,aluminium IVD coated Classification: 1100 MPa (at ambienttemperature) / 425 CLice

2、nsed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 August2009 BSI 2009ISBN 978 0 580 56005 7Amendments/corrigenda issued since publicationDate Comments

3、BS EN 4071:2009National forewordThis British Standard is the UK implementation of EN 4071:2009.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest

4、 to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/200

5、9 07:37, Uncontrolled Copy, (c) BSIBS EN 4071:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4071 July 2009 ICS 49.030.20 English Version Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1

6、 100 MPa (at ambient temperature) / 425 C Srie arospatiale - Vis tte hexagonale normale, ft normal tolrance serre, filetage court, en alliage de titane, revtues aluminium IVD - Classification: 1 100 MPa ( temprature ambiante) / 425 C Luft- und Raumfahrt - Sechskant-Paschrauben, kurzes Gewinde, aus T

7、itanlegierung, Aluminium IVD beschichtet - Klasse: 1 100 MPa (bei Raumtemperatur) / 425 C This European Standard was approved by CEN on 23 April 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

8、 of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A v

9、ersion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic,

10、 Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORM

11、ALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4071:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37,

12、 Uncontrolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics .54 Designation 85 Marking .86 Technical specification .87 Oversized bolts 9Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncont

13、rolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 3 Foreword This document (EN 4071:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Stand

14、ard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest

15、by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such

16、 patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

17、Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontrolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009

18、(E) 4 1 Scope This standard specifies the characteristics of bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated. Classification: 1 100 MPa 1) / 425 C 2)2 Normative references The following referenced documents are indispensable for the a

19、pplication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 4016, Aerospace series Oversized bolts 3)EN 9100, Ae

20、rospace series Quality management systems - Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994) EN 9133, Aerospace series Quality management systems Qualification procedure for a

21、erospace standard parts TR 3775, Aerospace series Bolts and pins Materials 4)MIL-C-83488C, Coating, aluminium, ion vapor deposited 5)ISO 3193, Aerospace Bolts, normal hexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or

22、 equal to 1 100 MPa Dimensions ISO 3353-1, Aerospace Lead and runout threads Part 1: Rolled external threads ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts ISO 7913, Aerospace Bolts and screws, metric Tolerances of form and position ISO 9152, Aerospace Bolts, with MJ th

23、reads, in titanium alloys, strength class 1 100 MPa Procurement specification 1) Minimum tensile strength of the material at ambient temperature. 2) Maximum temperature that the bolt can withstand without continuous change in its original characteristics, after return to ambient temperature. The max

24、imum temperature is determined by the surface treatment. 3) Published as ASD Prestandard at the date of publication of this standard. 4) Published as ASD Technical Report at the date of publication of this standard. 5) Published by: Department of Defense (DoD), the Pentagon, Washington,DC 20301, U.S

25、.A. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontrolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 5 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 1. Dimensions and tolerances are: in conformity with ISO 3193, expressed in m

26、illimetres and apply after surface treatment. Details of form not stated are left to the manufacturers discretion. 3.2 Surface roughness ISO 7913 3.3 Materials TR 3775 (titanium alloy, strength class 1 100 MPa) 3.4 Surface treatment MIL-C-83488C, type II, class 3, 4 m to 12 m. After aluminium deposi

27、t: mechanical blasting, followed by a chromate conversion coating within 24 h max. 6); optional lubrication with cethylic alcohol (code E). 6) Products used shall be in conformity with national regulation into force. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontroll

28、ed Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 6 Values in micrometres apply prior to surface treatment. Break sharp edges 0,1 to 0,4. Details of form not stated are left to the manufacturers discretion. Key 1 Continuous surface 2 2 holes D6 (optional) 3 1 hole D7 (optional) 4 Thread 5 Conforms to

29、ISO 3353-1 6 Marking Figure 1 3,2 0,8 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontrolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 7 Table 1 Diameter code Thread aD1D2D3D4bD5D6D7E F G nom. Tol. min. 0 0,5 min. nom. Tol. H13 H13 min. max. min. 0 0,3 030 MJ30,5 4h

30、6h 3 0,006 0,0315,5 5,4 2,30 0,5 6,5 0,4 0,2 2 040 MJ40,7 4h6h 4 0,010 0,0356,4 6,4 3 1,1 7,6 0,5 2,5 050 MJ50,8 4h6h 5 7,4 5,25 7,4 3,4 0,5 1 1,5 8,7 3 060 MJ61 4h6h 6 9,4 6,25 9,3 4,21,4 10,9 3,5 070 MJ71 4h6h 7 0,013 0,03810,3 7,25 10,2 5,21,9 12 4 080 MJ81 4h6h 8 12,3 8,25 12,2 6,2 14,3 4,5 100

31、MJ101,25 4h6h 10 16,3 10,25 16 7,91,6 2,4 18,9 0,6 0,3 5 120 MJ121,25 4h6h 12 0,016 0,04118,3 12,25 18 9,8 21,1 6 140 MJ141,5 4h6h 14 21,3 14,25 21 11,53 24,5 7 160 MJ161,5 4h6h 16 23,3 16,25 23 13,5 26,8 8 180 MJ181,5 4h6h 18 26,3 18,25 26 15,53,8 30,2 9 200 MJ201,5 4h6h 20 0,020 0,04529,3 20,25 29

32、 17,5 33,6 10 Diameter code H J K L1 0,2c, dL2L3N R Mass e nom. Tol. Length code nom. 0 0,3 nom. Tol. fg030 6 h12 002 to 030 2 to 30 6 0,4 0 0,2 0,49 0,03 040 7 002 to 040 2 to 40 7,5 5 0,93 0,06 050 1,35 8 3,25 003 to 050 3 to 50 9 6 2 0,5 1,63 0,09 060 1,6 10 h13 4,1 003 to 060 3 to 60 10 7 2,3 0,

33、7 3,05 0,12 070 1,85 11 4,5 004 to 070 4 to 70 11 2,7 4,17 0,17 080 2,1 13 5,35 004 to 080 4 to 80 11,5 7,5 3 6,28 0,22 100 2,35 17 7,1 005 to 100 5 to 100 14,5 9 3,4 0,8 0 0,3 12,19 0,35 120 2,85 19 7,9 006 to 120 6 to 120 16 10 4 0,9 19,49 0,50 140 3,35 22 9,2 007 to 140 7 to 140 19 12 4,7 1,1 30,

34、01 0,68 160 3,85 24 10,05 008 to 160 8 to 160 20,5 12,5 5,4 43,88 0,88 180 4,35 27 11,3 009 to 180 9 to 180 22,5 14,5 6 1,3 61,84 1,12 200 4,85 30 12,6 010 to 200 10 to 200 24,5 15 6,7 84,60 1,38 aIn accordance with ISO 5855-2. except the thread major diameter “d max.“ which shall be equal to D1min.

35、 0,025. bD4 max. shall be less than J. cIncrements: - 1 for L1 30; - 2 for 30 100. dIf greater lengths are required, they shall be chosen using the above increments. The length code corresponds to the length L1, completed by one or two zeros to the left, where necessary, to obtain a three digit code

36、. eApproximate values (kg/1 000 pieces), calculated on the basis of 4,45 kg/dm3, for information purposes only. They apply to bolts without holes. f Value for head and first L4.g Increase for each additional millimetre of L4. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, U

37、ncontrolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 8 4 Designation EXAMPLE Description block BOLT Identity block EN4071D080060E Number of this standard Hole code (see Table 2) Diameter code (see Table 1) Length code (see Table 1) Lubrication code (see 3.4) NOTE If necessary the originator code

38、 I9005 shall be placed between the description block and the identity block. Table 2 Holes Code Lockwire H Split pin D Lockwire and split pin C No hole (hyphen) 5 Marking See Table 3 and Figure 1, intended. Table 3 Diameter code EN 2424 Style 030 and 040 N 050 to 200 C + MJ 6 Technical specification

39、 ISO 9152, with the following modifications. 6.1 Approval of manufacturers EN 9100 6.2 Qualification of bolts EN 9133 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontrolled Copy, (c) BSIBS EN 4071:2009EN 4071:2009 (E) 9 6.3 Requirement deleted Double shear strength 7 O

40、versized bolts EN 4016 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/12/2009 07:37, Uncontrolled Copy, (c) BSIBS EN4071:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent natio

41、nal body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the lat

42、est amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can b

43、e found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standa

44、rds publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementat

45、ion of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information s

46、ervices are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of stan

47、dards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website a

48、t http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary