BS EN 3645-010-2006 Aerospace series - Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 C or 200 C continuous - Part 010 Receptac.pdf

《BS EN 3645-010-2006 Aerospace series - Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 C or 200 C continuous - Part 010 Receptac.pdf》由会员分享，可在线阅读，更多相关《BS EN 3645-010-2006 Aerospace series - Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 C or 200 C continuous - Part 010 Receptac.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3645-010:2006Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 010: Receptacle, hermetic, round flange, jam nut mounting Product standardThe European Standard EN 3645-010:2006 has

2、 the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:0

3、0 2007, Uncontrolled Copy, (c) BSIBS EN 3645-010:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978-0-580-49952-4National forewordThis British Standard was published by BSI. It is the UK implementation of EN

4、3645-010:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.This

5、 publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na

6、, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3645-010 December 2006 ICS 49.060 English Version Aerospace series - Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200

7、C continuous - Part 010: Receptacle, hermetic, round flange, jam nut mounting - Product standard Srie arospatiale - Connecteurs lectriques circulaires contacts protgs, accouplement par filetage pas rapide trois filets, tempratures dutilisation 175 C ou 200 C continu - Partie 010 : Embase collerette

8、ronde, hermtique fixation par crou - Norme de produit Luft- und Raumfahrt - Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung, Dauerbetriebstemperaturen 175 C oder 200 C - Teil 010: Hermetischer Fester Steckverbinder mit runden Schwei und Mutternbefestigung - Prod

9、uktnorm This European Standard was approved by CEN on 28 September 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra

10、phical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a C

11、EN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi

12、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Bruss

13、els 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3645-010:2006: ELicensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Term

14、s and definitions .4 4 Required characteristics.5 5 Designation 8 6 Marking .8 7 Technical specification .8 EN 3645-010:2006Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI3 Foreword This document (EN 3645-010:2006) has been prepared by the Aerospace and De

15、fence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its pre

16、sentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. Attention is drawn to the possibility

17、 that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are boun

18、d to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

19、and the United Kingdom. EN 3645-010:2006Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies the characteristics of hermetic receptacles with jam nut mounting in the family of circular, electrical connectors, with triple start t

20、hreaded coupling. It applies to models in Table 3. For plugs and protective covers, see EN 3645-006, EN 3645-008, EN 3645-011 and EN 3645-012 respectively. The contacts are unremovable and soldered termination. These connectors are derived from and interchangeable with model Y in specification MIL-D

21、TL-38999/23. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3645-001,

22、Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 001: Technical specification. EN 3645-002, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating te

23、mperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements. EN 3645-006, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 006: Protective cover for receptacle

24、Product standard. EN 3645-008, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 008: Non release plug with grounding ring Product standard. EN 3645-011, Aerospace series Connectors, electrical, circul

25、ar, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 011: Lanyard release plug with grounding fingers Type 1 Product standard. EN 3645-012, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating tempe

26、rature 175 C or 200 C continuous Part 012: Lanyard release plug with grounding fingers Type 2 Product standard. MIL-DTL-38999/23, Connectors, electrical, circular, threaded, receptacle, jam-nut mounting, hermetic, hermetic solder contacts, series III, metric.1)3 Terms and definitions For the purpose

27、s of this document, the terms and definitions given in EN 3645-001 apply. 1) Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301 USA. EN 3645-010:2006Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI5 4 Required characteristics 4.1

28、 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. Key 1 Red strip 3 H on flats 2 3 holes 1,5 min. for brake wire (see option according to Detail D) 4 B on flat 5 Seal NOTE One disengagement is permissible to accept the accessory mounting. Figure 1 Hermetic

29、jam nut receptacle Option D (Slot with close edges) (without seal) Seal EN 3645-010:2006Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI6 Table 1 Hermetic jam nut receptacle - Dimensions A B C aD E F bG H K max. Shell size 0,3 + 0,10 0,15 + 0,10 0,20 + 0,13

30、 0,03 0,13 max. Thread Male contact Female contact09 30,2 16,53 17,40 15,9 M171 6g 0,1 R 24,00 21,82 11 34,9 19,07 20,60 18,8 M201 6g 0,1 R 27,00 24,99 5,3 5,9 13 38,1 23,82 25,40 23,8 M251 6g 0,1 R 32,00 29,77 15 41,3 26,97 28,50 26,8 M281 6g 0,1 R 36,00 32,91 17 44,5 30,15 31,85 2,39 1,14 30,8 M32

31、1 6g 0,1 R c37,00 36,12 19 49,2 33,32 34,90 33,8 M351 6g 0,1 R 41,00 39,25 21 52,4 36,50 37,9036,8 M381 6g 0,1 R 46,00 42,47 23 55,6 39,67 41,20 39,8 M411 6g 0,1 R 50,00 45,61 25 58,7 42,85 44,40 3,58 1,91 42,8 M441 6g 0,1 R 51,23 49,25 5,1 5,7 L M N P S W X Y Z Mass g + 0,3 0 0,13 + 0,4 0,1 0,4 + 0

32、,7 0,1 max. Stainless steel 9,10 16,3 15,30 27,0 20,5020,19 34 9,10 19,4 16,40 14,1 31,8 29,2 25,2724,97 41 9,10 22,7 21,60 34,9 28,4528,14 50 9,10 25,9 24,80 38,1 31,6231,32 62 9,10 29,0 28,00 41,3 2,2 29,3 34,8034,49 1,85 1,70 83 9,70 32,2 31,20 46,0 37,9237,62 108 9,70 35,4 34,30 49,2 41,2040,69

33、141 9,70 38,6 37,50 52,4 44,3743,86 172 9,70 41,7 40,70 14,3 55,6 3,0 30,1 47,5547,04 2,69 2,54 203 aDimensions C and 1,5 mm shall be compatible with the panel hole bDiameter F corresponds to the start of the thread cUpper diameter modified as follow: 31,95 max. 31,80 min. EN 3645-010:2006Licensed C

34、opy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI7 4.2 Materials and surface treatment See Table 3. 4.3 Recommended panel cut-out See Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Figure 2 Panel cut-out Table 2 Panel cut-out - Dimensions A B C Sh

35、ell size + 0,25 0 0 0,25 min. 09 17,70 16,99 31,80 11 20,88 19,53 35,00 13 25,58 24,26 39,40 15 28,80 27,53 42,50 17 31,98 30,68 45,70 19 35,15 33,86 48,50 21 38,28 37,06 51,70 23 41,50 40,24 54,90 25 44,68 43,41 58,00 4.4 Electrical, mechanical and climatic characteristics See EN 3645-002. EN 3645-

36、010:2006Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSI8 5 Designation EXAMPLE Description block JAM NUT ELECTRICAL CONNECTOR Identity block EN3645-Y7GN35MA Number of the basic standard Model according to Table 3 Shell code for nut mounting receptacle Shel

37、l size code according to Table 4 Only N: no grounded cavity Contact arrangement according to EN 3645-002 except those containing coaxial or triaxial contacts or size 10 contacts Contact code M: male with solder cup X: male with eyelet Polarization: N, A, B, C, D, E NOTE If necessary, the code I9005

38、shall be placed between the description block and the identity block. Table 3 Model coding Model Description Y Hermetic receptacles, with shell in stainless steel Soldered contacts Maximum operating temperature 200 C continuous Table 4 Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21

39、 G23 H 25 J 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001. EN 3645-010:2006Licensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c) BSIblankLicensed Copy: Wang Bin, na, Fri Mar 23 00:09:30 GMT+00:00 2007, Uncontrolled Copy, (c)

40、BSIBS EN 3645-010:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBr

41、itish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity w

42、hile using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscr

43、ibers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI

44、 website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European an

45、d international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: in

46、fobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-

47、.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publicati

48、ons of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permissi

49、on from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Co