BS EN 3642-1997 Rivets solid 100 countersunk normal head with dome in titanium TI-PO2 anodized inch based series《阳极氧化TI-PO2钛制100标准埋头圆顶实心铆钉 英制系列》.pdf

《BS EN 3642-1997 Rivets solid 100 countersunk normal head with dome in titanium TI-PO2 anodized inch based series《阳极氧化TI-PO2钛制100标准埋头圆顶实心铆钉 英制系列》.pdf》由会员分享，可在线阅读，更多相关《BS EN 3642-1997 Rivets solid 100 countersunk normal head with dome in titanium TI-PO2 anodized inch based series《阳极氧化TI-PO2钛制100标准埋头圆顶实心铆钉 英制系列》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3642:1997 Rivets, solid, 100 countersunk normal head, with dome, in titanium TI-PO2, anodized, inch based series The European Standard EN 3642:1996 has the status of a British Standard ICS 49.030.99BSEN 3642:1997 This British Standard, having been prepared und

2、er the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1997 BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 90/76227 DC ISBN 0 580 27030

3、0 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association of Electronics, Telecommunications and Business Equipment

4、Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBSEN 3642:1997 BSI 11-1998 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3

5、2 Normative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 Figure 1 4 Table 1 3 Table 2 5 List of references Inside back coverBSEN 3642:1997 ii BSI 11-1998 National foreword This British Standard has been prepared by Technical Committee ACE/12 and i

6、s the English language version of EN 3642:1996 Aerospace series Rivets, solid,100 countersunk normal head with dome, in titanium TI-PO2, anodized, inch based series, published by the European Committee for Standardization (CEN). EN 3642:1996 was produced as a result of international discussions in w

7、hich the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligatio

8、ns. Cross-references Publication referred to Corresponding British Standard EN 2424:1995 BS EN 2424:1995 Marking of aerospace products ISO 8080:1985 BS M 58:1986 Specification for anodic coating of titanium and titanium alloys by the sulphuric acid process Summary of pages This document comprises a

9、front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STA

10、NDARD NORME EUROPENNE EUROPISCHE NORM EN 3642 September 1996 ICS 49.040.20 Descriptors: Aircraft industry, rivet, countersunk head rivet, titanium, characteristic, dimension, dimensional tolerance, designation English version Aerospace series Rivets, solid, 100 countersunknormalhead with dome, in ti

11、tanium TI-PO2, anodized, inch based series Srie arospatiale Rivets ordinaires, tte fraise 100 normale avec dme, en titane TI-PO2, anodiss, srie base inches Luft- und Raumfahrt Vollniete, mit 100 normalem Senkkopf mit Dom, aus Titan TI-PO2, anodisiert, Zoll-Reihe This European Standard was approved b

12、y CEN on 1996-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

13、 may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the C

14、entral Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN Europe

15、an Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 3642:1996 EEN3642:1996 BSI 11-1998 2 Foreword This European Standard has been prepared by the Eur

16、opean Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to

17、CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 1997, and conflicting national standards shall be withdrawn at the latest by March 1997. According to the CEN/CENELEC Internal Regulation

18、s, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.EN3642:

19、1996 BSI 11-1998 3 1 Scope This standard specifies the characteristics of solid rivets, with 100 countersunk normal head with dome, in titanium TI-PO2, anodized, inch based series, for maximum operating temperature 315 C. 2 Normative references This European Standard incorporates by dated or undated

20、 reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when inco

21、rporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. ISO 8080, Aerospace Anodic treatment of titanium and titanium alloys Sulfuric acid process. ISO 10299, Aerospace Identification marking of solid rivets 1) . EN 2424, Aerospace s

22、eries Marking of aerospace products. EN 3378, Aerospace series Titanium TI-PO2 Annealed 330 # R c# 410 MPa Wire for rivet 1,6 # d # 10 mm 2) . EN 3627, Aerospace series Titanium solid rivets Technical specification 1) . 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and

23、Table 1 and Table 2. Dimensions and tolerances are expressed in millimetres and apply after surface treatment. 3.2 Material EN 3378 3.3 Surface treatment ISO 8080 Table 1 1) In preparation at the date of publication of this standard 2) Published as AECMA Prestandard at the date of publication of thi

24、s standard Diameter code D 1 a D 2 b D 3 D 4 D 5 D 6 L 2 L 3 L 4 L 5 L 6 R max. min. min. max. min. max. min. min. max. min. 0,08 024 2,45 2,35 4,45 4 3,2 2,4 3,54 1,9 1,6 0,9 0,05 0,38 2,4 0,8 0,5 0,15 032 3,25 3,15 5,95 5,35 4,3 3,2 4,82 2,6 2,3 1,1 0,06 0,47 2,6 1 0,7 036 3,65 3,55 6,7 6 4,8 3,6

25、5,46 2,9 2,5 1,3 0,07 0,52 2,9 1,1 0,25 040 4,05 3,94 7,4 6,6 5,3 4 5,79 3,2 2,8 1,4 0,08 0,68 3 1,2 0,8 048 4,85 4,73 8,9 7,95 6,4 4,8 7,39 3,8 3,3 1,8 0,1 0,63 3,8 1,5 1 a D 1max. may increase by 0,03, over length (L 5 L 2 ). b Maximum condition 0 0,08 EN3642:1996 4 BSI 11-1998 Figure 1EN3642:1996

26、 BSI 11-1998 5 Table 2 Diameter code 024 032 036 040 048 Length a Mass b a Mass b a Mass b a Mass b a Mass b code N R N R N R N R N R 004 4 0,106 0,203 0,258 005 5 0,126 0,239 0,302 006 6 0,147 0,276 0,344 0,455 007 7 0,167 0,312 0,385 0,511 008 8 0,188 0,349 0,427 0,567 0,848 009 9 0,208 0,383 0,46

27、9 0,623 0,929 010 10 0,228 0,420 0,512 0,679 1,010 011 11 0,249 0,456 0,553 0,735 1,091 012 12 0,269 0,493 0,595 0,792 1,173 013 13 0,290 0,529 0,637 0,848 1,254 014 14 0,310 0,565 0,678 0,905 1,336 015 15 0,330 0,601 0,720 0,961 1,417 016 16 0,351 0,637 0,764 1,017 1,499 017 17 0,371 0,673 0,805 1,

28、074 1,580 018 18 0,392 0,709 0,848 1,130 1,662 019 19 0,412 0,745 0,890 1,187 1,743 020 20 0,432 0,782 0,932 1,244 1,824 022 22 0,855 1,015 1,357 1,987 024 24 0,928 1,100 1,470 2,150 026 26 1,183 1,583 2,313 028 28 1,270 1,696 2,476 030 30 1,810 2,638 032 32 1,923 2,801 035 35 2,964 040 40 3,127 a T

29、ail end code (see Figure 1) b Approximate values (kg/1 000 pieces), calculated on the basis of 4,45 kg/dm 3 , given for information purposes only L 1 + 0,5 0EN3642:1996 6 BSI 11-1998 4 Designation EXAMPLE: NOTEIf necessary, the code I9005 shall be placed between the description block and the identit

30、y block. 5 Marking 5.1 Rivet EN 2424, style G 5.2 Material ISO 10299 6 Technical specification EN 3627BSEN 3642:1997 BSI 11-1998 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

31、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK

32、view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve

33、 the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020

34、 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 89

35、96 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, Europea

36、n and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing membe

37、rs of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI

38、 also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying,

39、 recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.