BS EN 3142-1996 Rivets solid universal head in heat resisting nickel base alloy NI-P11 inch based series《耐高温镍基合金NI-P11通用头实心铆钉 英制系列》.pdf

《BS EN 3142-1996 Rivets solid universal head in heat resisting nickel base alloy NI-P11 inch based series《耐高温镍基合金NI-P11通用头实心铆钉 英制系列》.pdf》由会员分享，可在线阅读，更多相关《BS EN 3142-1996 Rivets solid universal head in heat resisting nickel base alloy NI-P11 inch based series《耐高温镍基合金NI-P11通用头实心铆钉 英制系列》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3142:1996 Rivets, solid, universal head, in heat resisting nickel base alloy, NI-P11, inch based series The European Standard EN3142:1996 has the status of a BritishStandard ICS 49.040.20BSEN3142:1996 This BritishStandard, having been prepared under the direct

2、ionof the Engineering SectorBoard, was published underthe authority of theStandards Board andcomesintoeffect on 15June1996 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment90/76229 DC ISBN 0 580 25943 9 Committees responsible f

3、or this BritishStandard The preparation of this BritishStandard was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association of Electronic, Telecommunications and Business Equipment Industries British Industrial

4、 Fasteners Federation Ministry of Defence Society of British Aerospace Companies Amendments issued since publication Amd. No. Date CommentsBSEN3142:1996 BSI 12-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Required

5、 characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 Figure 1 4 Table 1 4 Table 2 5 List of references Inside back coverBSEN3142:1996 ii BSI 12-1999 National foreword This BritishStandard has been prepared by Technical Committee ACE/12 and is the English language version of EN3

6、142:1996 Aerospace seriesRivets, solid, universal head, in heat resisting nickel base alloy NI-P11, inch based series, published by the European Committee for Standardization (CEN). EN3142:1996 was produced as a result of international discussions in which the UnitedKingdom took an active part. A Br

7、itish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corr

8、esponding BritishStandard EN2000:1991 BS EN2000:1992 Quality assurance. EN aerospace Products. Approval of the quality system of manufacturers EN2424:1995 BS EN2424:1995 Marking of aerospace products Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN t

9、itle page, pages2 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3142 March 1996 ICS

10、 49.040.20 Descriptors: Aircraft industry, rivet, round head rivet, flat head rivet, nickel alloy, heat resistant material, dimension, designation English version Aerospace seriesRivets, solid, universal head, in heat resisting nickel base alloy NI-P11, inch based series Srie arospatialeRivets ordin

11、aires, tte ronde aplatie, en alliage rsistant chaud base de nickel NI-P11, srie base inches Luft- und RaumfahrtVollniete, mit Universalkopf, aus hochwarmfester Nickelbasislegierung NI-P11, Zoll-Reihe This European Standard was approved by CEN on1995-08-31. CEN members are bound to comply with the CE

12、N/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to

13、 any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions

14、. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation

15、Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN3142:1996 EEN3142:1996 BSI 12-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inqui

16、ries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approval of the National Associations and the Official Services of the members countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the stat

17、us of a national standard, either by publication of an identical text or by endorsement, at the latest by September1996, and conflicting national standards shall be withdrawn at the latest by September1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of th

18、e following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom.EN3142:1996 BSI 12-1999 3 1 Scope This standard specifies

19、 the characteristics of solid rivets, with universal head, in heat resisting nickel base alloy NI-P11, inch based series, for maximum operating temperature650 C. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normati

20、ve references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated referenc

21、es the latest edition of the publication referred to applies. ISO10299, AerospaceIdentification marking of solid rivets 1) . EN2000, Aerospace seriesQuality assuranceEN aerospace productsApproval of the quality system of manufacturers. EN2305, Nickel base alloy NI-P11540MPak R m k 620MPaBars and wir

22、es for rivetsAerospace series 2) . EN2424, Aerospace seriesMarking of aerospace products. EN2941, Aerospace seriesNickel alloy rivetsTechnical specification 3) . 3 Required characteristics 3.1 ConfigurationDimensionsMasses SeeFigure 1 and Table 1 and Table 2. Dimensions and tolerances are expressed

23、in millimetres. 3.2 Material EN2305 1) In preparation at the date of publication of this standard 2) Published as AECMA Standard at the date of publication of this standard 3) Published as AECMA Prestandard at the date of publication of this standardEN3142:1996 4 BSI 12-1999 Table 1 Figure 1 Diamete

24、r code D 1 a D 2 D 3 D 4 L 2 L 3 L 4 R 1 R 2 max. min. max. min. max. min. max. min. max. min. 0,08 024 2,45 2,35 5 4,5 2,4 1,8 1,9 1,6 1 1,4 0,8 0,5 2,9 0,15 032 3,25 3,15 6,7 6 3,2 2,4 2,6 2,3 1,4 1 0,7 3,9 036 3,65 3,55 7,5 6,8 3,6 2,7 2,9 2,5 1,6 1,6 1,1 4,4 0,25 040 4,05 3,94 8,3 7,5 4 3 3,2 2,

25、8 1,7 1,2 0,8 4,9 048 4,85 4,73 10 9 4,8 3,6 3,8 3,3 2 1,5 1 5,9 056 5,65 5,53 11,7 10,5 5,6 4,2 4,5 3,9 2,4 2 1,8 1,2 6,8 064 6,45 6,33 13,3 12,1 6,4 4,8 5,1 4,5 2,7 2,1 1,4 7,8 a D 1max. may increase by0,03, over length L 3 . +0,2 0EN 3142:1996 BSI 12-1999 5 Table 2 Diameter code 024 032 036 040 0

26、48 056 064 Length a Mass 2) a Mass 2) a Mass 2) a Mass 2) a Mass 2) a Mass 2) a Mass 2) code N R N R N R N R N R N R N R 004 4 0,237 0,478 0,727 005 5 0,279 0,552 0,814 006 6 0,321 0,622 0,897 1,036 007 7 0,362 0,696 0,981 1,148 008 8 0,401 0,766 1,064 1,260 1,873 009 9 0,442 0,840 1,147 1,376 2,036

27、 010 10 0,481 0,911 1,231 1,488 2,200 3,171 4,227 011 11 0,523 0,984 1,314 1,600 2,360 3,392 4,517 012 12 0,564 1,055 1,398 1,712 2,527 3,614 4,807 013 13 0,605 1,132 1,481 1,826 2,687 3,834 5,097 014 14 0,645 1,199 1,564 1,940 2,847 4,053 5,387 015 15 0,683 1,276 1,651 2,052 3,043 4,274 5,676 016 1

28、6 0,721 1,344 1,734 2,164 3,239 4,496 5,964 017 17 0,762 1,418 1,818 2,276 3,369 4,717 6,301 018 18 0,802 1,491 1,901 2,389 3,489 4,938 6,637 019 19 0,842 1,561 1,984 2,503 3,660 5,173 6,880 020 20 0,882 1,635 2,068 2,617 3,822 5,409 7,122 022 22 1,780 2,234 2,841 4,146 5,820 7,699 024 24 1,924 2,40

29、1 3,126 4,473 6,262 8,282 026 26 2,571 3,293 4,797 6,641 8,856 028 28 2,738 3,518 5,121 7,147 9,434 030 30 3,745 5,445 7,587 10,010 032 32 3,970 5,769 8,026 10,588 035 35 6,288 8,690 11,454 040 40 7,163 9,793 12,897 a Tail end code (seeFigure 1) 2) Approximate values (kg/1000 pieces), calculated on

30、the basis of8,85kg/dm 3 , given for information purposes only L 1 0,5 + 0EN3142:1996 6 BSI 12-1999 4 Designation EXAMPLE: NOTEIf necessary, the code19005 shall be placed between the description block and the identity block. 5 Marking 5.1 Rivet EN2424, style G 5.2 Material ISO10299 6 Technical specif

31、ication EN2941 plus EN2000 for the approval of manufacturersBSEN3142:1996 BSI 12-1999 List of references Seenational foreword.BS EN 3142:1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It pr

32、esents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BS

33、I to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000.

34、Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02

35、089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European

36、and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BS

37、I are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds th

38、e copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or

39、otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.