BS EN 3063-1994 Bolts double hexagon head close tolerance shank medium length thread in heat resisting nickel base alloy NI-P101HT (Waspaloy) Classification 1210 MPa (at ambient te.pdf

《BS EN 3063-1994 Bolts double hexagon head close tolerance shank medium length thread in heat resisting nickel base alloy NI-P101HT (Waspaloy) Classification 1210 MPa (at ambient te.pdf》由会员分享，可在线阅读，更多相关《BS EN 3063-1994 Bolts double hexagon head close tolerance shank medium length thread in heat resisting nickel base alloy NI-P101HT (Waspaloy) Classification 1210 MPa (at ambient te.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3063:1994 Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) Classification: 1210MPa (at ambient temperature)/730 C The European Standard EN3063:1994 has the status of a British Sta

2、ndard UDC 621.882.214.1-034.018.44:629.7BSEN3063:1994 This British Standard, having been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15November1994 BSI 01-2000 The following BSI references rel

3、ate to the work on this standard: Committee reference ACE/12 Draft for comment 88/76363 DC ISBN 0 580 22611 5 Cooperating organizations The European Committee for Standardization(CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the

4、following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization fo

5、r Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instit

6、uto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation UnitedKingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN3063:1994 BSI 01-20

7、00 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 8 5 Marking 8 6 Technical specification 8 National annex NA (informative) Committees responsible Inside back cover National an

8、nex NB (informative) Cross-references Inside back cover Figure 1 4 Table 1 4 Table 2 5BSEN3063:1994 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN3063:1994 Aerospace se

9、ries Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) Classification:1210MPa(at ambient temperature)/730 C, published by the European Committee for Standardization(CEN). EN3063:1994 was produced as a result of internati

10、onal discussions in which theUnited Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity

11、from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2 to8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indic

12、ated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN3063 August1994 UDC 621.882.214.1-034.018.44:629.7 Descriptors: Aircraft industry, fastener, screw, double hexagonal head screw, heat resistant steel, alloy steel, nickel alloy, classification,c

13、haracteristic, dimension, screw thread, code, designation, marking English version Aerospace series Bolts,doublehexagonhead,closetoleranceshank, mediumlength thread, in heat resisting nickel base alloy NI-P101HT(Waspaloy) Classification:1210MPa(atambient temperature)/730 C Srie arospatiale Vis tte b

14、ihexagonale, tige tolrance serre, filetage moyen, en alliage rsistant chaud base nickel NI-P101HT(Waspaloy) Classification:1210MPa( temprature ambiante)/730 C Luft- und Raumfahrt Zwlfkant-Paschrauben, mittlere Gewindelnge,aus hochwarmfester Nickelbasislegierung NI-P101HT(Waspaloy) Klasse:1210MPa (be

15、i Raumtemperatur)/730 C This European Standard was approved by CEN on1994-08-17. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and b

16、ibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions(English, French, German). A version in any other language made by translation under the responsibility

17、 of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portuga

18、l, Spain, Sweden, Switzerland andUnited Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN3063:1994 EEN3063:1994 BSI 01-2000 2 Fo

19、reword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official S

20、ervices of the membercountries of AECMA, prior to its presentation to CEN. This standard was submitted for Formal Vote, and the result was positive. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

21、 February1995, and conflicting national standards shall be withdrawn at the latest by February1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland,

22、 Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN3063:1994 BSI 01-2000 3 1 Scope This standard specifies the characteristics of double hexagon headed bolts with close tolerance shank and medium length thread, in NI-P101HT, for aerospace applications.

23、 Classification:1210MPa 1) /730 C 2) 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references

24、, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. ISO3353, Aerospace Rolled threads for bolts Lead and runout re

25、quirements. ISO4095, Fasteners for aerospace construction Bi-hexagonal wrenching configuration. ISO5855-2, Aerospace construction MJ threads Part2: Limit dimensions for bolts and nuts. EN2424, Aerospace series Marking of aerospace products 3) . EN2582, Aerospace series Bolts in heat resisting nickel

26、 base alloy NI-P101HT(Waspaloy) Classification:1210MPa/730 C Technical specification 4) . EN2959, Aerospace series Heat resisting nickel base alloy(NI-P101HT) Solution treated and coldworked Bar for hot upset forging for fasteners3k Dk 30mm 4) . EN3220, Aerospace series Heat resisting nickel base al

27、loy(NI-P101HT) Cold worked and softened Bar and wire for continuous forging or extrusion for fasteners 3k Dk 30mm 4) . 3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses SeeFigure 1 and Table 1 and Table 2. Dimensions and tolerances are in millimetres. 3.2 Materials EN2959 or

28、EN3220 1) Minimum tensile strength of the material at ambient temperature 2) Maximum test temperature of the parts 3) Published as AECMA Standard at the date of publication of this standard 4) Published as AECMA Prestandard at the date of publication of this standardEN3063:1994 4 BSI 01-2000 Table 1

29、 Figure 1 Thread ac D E F G H K Q R 1 S b T U V X Y Z Code Designation 17 max. min. min. min. h15 0,5 max. min. min. max. min. max. min. 050 MJ5 0,84h6h 5 9,1 8,3 6,8 1 5,5 3,4 0,5 0,3 7 2 2,9 2,5 3,7 3,2 0,002 0,12 0,13 060 MJ6 14h6h 6 10,6 9,8 7,8 1,2 6 4,2 0,7 0,5 8 2,3 3,2 2,8 4,6 4,1 0,15 070 M

30、J7 14h6h 7 12,1 11,3 8,8 1,4 6,5 5,2 9 2,6 3,7 3,3 5,4 4,9 0,15 0,18 080 MJ8 14h6h 8 13,6 12,8 9,8 1,6 7 6,2 10 2,8 4,1 3,7 5,7 5,2 0,2 100 MJ10 1,254h6h 10 16,7 15,7 11,8 2 8 7,9 0,8 0,6 12 3,1 5,1 4,7 7,2 6,7 0,0015 0,25 120 MJ12 1,254h6h 12 19,9 18,8 13,7 2,4 9,2 9,8 0,9 14 3,5 6 5,6 8,5 8 0,18 0

31、,3 a In accordance with ISO5855-2 b Bihexagonal wrenching configuration in conformity with ISO4095 over length T min. c The thread major diameter “d” shall be: d max.=D min.0,025; d min.: seeISO5855-2.EN 3063:1994 BSI 01-2000 5 Table 2 Length code L 0,2 Thread code 050 060 070 080 100 120 N 0,3 Mass

32、 a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a 003 3 15 4,08 17 6,21 004 4 16 4,24 18 6,44 19 9,13 20,5 13,00 005 5 17 4,41 19 6,68 20 9,46 21,5 13,41 25,5 23,91 006 6 18 4,57 20 6,91 21 9,76 22,5 13,82 26,5 24,56 28,5 39,22 007 7 19 4,73 21 7,14 22 10,08 23,5 14,24 27,5 25,21 2

33、9,5 40,15 008 8 20 4,89 22 7,37 23 10,40 24,5 14,65 28,5 25,85 30,5 41,08 009 9 21 5,05 23 7,61 24 10,72 25,5 15,07 29,5 26,50 31,5 42,02 010 10 22 5,21 24 7,84 25 11,04 26,5 15,48 30,5 27,15 32,5 42,95 011 11 23 5,38 25 8,07 26 11,35 27,5 15,90 31,5 27,80 33,5 43,88 012 12 24 5,54 26 8,31 27 11,67

34、28,5 16,31 32,5 28,44 34,5 44,81 013 13 25 5,70 27 8,54 28 11,99 29,5 16,73 33,5 29,09 35,5 45,75 014 14 26 5,86 28 8,77 29 12,30 30,5 17,16 34,5 29,73 36,5 46,68 015 15 27 6,03 29 9,01 30 12,62 31,5 17,55 35,5 30,39 37,5 47,61 016 16 28 6,19 30 9,24 31 12,94 32,5 17,97 36,5 31,03 38,5 48,54 017 17

35、29 6,35 31 9,47 32 13,26 33,5 18,38 37,5 31,68 39,5 49,48 018 18 30 6,51 32 9,71 33 13,57 34,5 18,80 38,5 32,33 40,5 50,41 019 19 31 6,67 33 9,94 34 13,89 35,5 19,21 39,5 32,98 41,5 51,34 020 20 32 6,84 34 10,17 35 14,21 36,5 19,63 40,5 33,62 42,5 52,27 021 21 33 7,00 35 10,41 36 14,52 37,5 20,04 41

36、,5 34,27 43,5 53,21 022 22 34 7,16 36 10,64 37 14,84 38,5 20,46 42,5 34,92 44,5 54,14 023 23 35 7,32 37 10,87 36 15,16 39,5 20,87 43,5 35,57 45,5 55,07 024 24 36 7,48 38 11,11 39 15,48 40,5 21,28 44,5 36,21 46,5 56,00 025 25 37 7,65 39 11,34 40 15,79 41,5 21,70 45,5 36,86 47,5 56,94 026 26 38 7,81 4

37、0 11,57 41 16,11 42,5 22,11 46,5 37,51 48,5 57,87 027 27 39 7,97 41 11,80 42 16,43 43,5 22,53 47,5 38,16 49,5 58,80 028 28 40 8,13 42 12,04 43 16,75 44,5 22,94 48,5 38,80 50,5 59,73EN 3063:1994 6 BSI 01-2000 Table 2 Length code L 0,2 Thread code 050 060 070 080 100 120 N 0,3 Mass a N 0,3 Mass a N 0,

38、3 Mass a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a 029 29 41 8,29 43 12,27 44 17,06 45,5 23,36 49,5 39,45 51,5 60,67 030 30 42 8,46 44 12,50 45 17,38 46,5 23,77 50,5 40,10 52,5 61,60 032 32 44 8,78 46 12,97 47 18,02 48,5 24,57 52,5 41,40 54,5 63,46 034 34 46 9,10 48 13,44 49 18,65 50,5 25,43 54,5 42,69

39、 56,5 65,33 036 36 48 9,43 50 13,90 51 19,29 52,5 26,26 56,5 43,99 58,5 67,19 038 38 50 9,75 52 14,37 53 19,92 54,5 27,09 58,5 45,28 60,5 69,06 040 40 52 10,07 54 14,84 55 20,55 56,5 27,92 60,5 46,58 62,5 70,93 042 42 54 10,40 56 15,30 57 21,19 58,5 28,75 62,5 47,87 64,5 72,79 044 44 56 10,72 58 15,

40、77 59 21,82 60,5 29,57 64,5 49,17 66,5 74,66 046 46 58 11,05 60 16,24 61 22,46 62,5 30,40 66,5 50,46 68,5 76,52 048 48 60 11,37 62 16,70 63 23,09 64,5 31,23 68,5 51,76 70,5 78,39 050 50 62 11,69 64 17,17 65 23,73 66,5 32,06 70,5 53,05 72,5 80,25 052 52 66 17,63 67 25,36 68,5 32,89 72,5 54,35 74,5 82

41、,12 054 54 68 18,10 69 25,00 70,5 33,72 74,5 55,64 76,5 83,98 056 56 70 18,57 71 25,63 72,5 34,55 76,5 56,94 78,5 85,85 058 58 72 19,03 73 26,27 74,5 35,38 78,5 58,23 80,5 87,71 060 60 74 19,50 75 26,90 76,5 36,21 80,5 59,53 82,5 89,58 062 62 77 27,54 78,5 37,04 82,5 60,82 84,5 91,44 064 64 79 28,17

42、 80,5 37,86 84,5 62,12 86,5 93,31 066 66 81 28,80 82,5 38,69 86,5 63,41 88,5 95,17 068 68 83 29,44 84,5 39,52 88,5 64,71 90,5 97,04 070 70 85 30,07 86,5 40,35 90,5 66,00 92,5 98,90 072 72 88,5 41,18 92,5 67,30 94,5 100,77 074 74 90,5 42,01 94,5 68,59 96,5 102,63 076 76 92,5 42,84 96,5 69,89 98,5 104

43、,50EN 3063:1994 BSI 01-2000 7 Table 2 Length code L 0,2 Thread code 050 060 070 080 100 120 N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a N 0,3 Mass a 078 78 94,5 43,67 98,5 71,18 100,5 106,36 080 80 96,5 44,49 100,5 72,48 102,5 108,23 082 82 102,5 73,77 104,5 110,09 084 84 104,5

44、76,07 106,5 111,96 086 86 106,5 76,36 108,5 113,82 088 88 108,5 77,66 110,5 116,69 090 90 110,5 78,95 112,5 117,55 092 92 112,5 80,25 114,5 119,42 094 94 114,5 81,54 116,5 121,28 096 96 116,5 82,84 118,5 123,15 098 98 118,5 84,13 120,5 125,01 100 100 120,5 85,43 122,5 126,88 104 104 126,5 130,61 108

45、 108 130,5 134,34 112 112 134,5 138,07 116 116 138,5 141,80 120 120 142,5 145,53 a Mass. quoted in kg/1000partsEN3063:1994 8 BSI 01-2000 4 Designation EXAMPLE: NOTEIf necessary, the codeI9005 shall be placed between the description block and the identity block. 5 Marking EN2424, style A, as indicate

46、d on Figure 1. 6 Technical specification EN2582BSEN3063:1994 BSI 01-2000 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee(ACE/-) to Technical Committee ACE/12

47、, upon which the following bodies were represented: Association of Electronics, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. National annex NB (informative) Cross-references The BritishSta

48、ndards corresponding to the International Standards referred to in the text are as follows. International Standard Corresponding BritishStandard ISO3353:1992 BS2A231:1993 Rolled threads for bolts Lead and runout requirements ISO5855-2:1988 BS6293 MJ threads for aerospace construction Part2:1982 Spec

49、ification for dimensions for bolts and nutsBS EN 3063:1994 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure t