BS EN 303-7-2006 Heating boilers - Part 7 Gas-fired central heating boilers nequipped with a forced draught burner of nominal heat output not exceeding 1 000 kW《加热锅炉 第7部分 用标称热输出小于等.pdf

《BS EN 303-7-2006 Heating boilers - Part 7 Gas-fired central heating boilers nequipped with a forced draught burner of nominal heat output not exceeding 1 000 kW《加热锅炉 第7部分 用标称热输出小于等.pdf》由会员分享，可在线阅读，更多相关《BS EN 303-7-2006 Heating boilers - Part 7 Gas-fired central heating boilers nequipped with a forced draught burner of nominal heat output not exceeding 1 000 kW《加热锅炉 第7部分 用标称热输出小于等.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 303-7:2006Heating boilers Part 7: Gas-fired central heating boilers equipped with a forced draught burner of nominal heat output not exceeding 1 000 kWThe European Standard EN 303-7:2006 has the status of a British StandardICS 91.140.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g4

2、3g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Tue Apr 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 303-7:2006This British Standard was published

3、 under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 0 580 49826 3National forewordThis British Standard was published by BSI. It is the UK implementation of EN 303-7:2006. The UK participation in its preparation was entrusted to Technical Committee GSE

4、/29, Gas-fired central heating boilers (domestic and non-domestic) and domestic gas-fired water heaters.A list of organizations represented on GSE/29 can be obtained on request to its secretary.EN 303-7:2006 is a candidate “harmonized” European standard and fully takes into account the requirements,

5、 given under the EU gas appliances (90/396/EEC) and boiler efficiency (92/42/EEC) Directives, and intended to lead to CE marking. The date of applicability of EN 303-7:2006 as a harmonized European standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to a

6、n announcement in the Official Journal of the European Communities. The Commission in consultation with Member States has agreed a transition period for the co-existence of harmonized European standards and their corresponding national standard(s). It is intended that this period will comprise a per

7、iod, usually nine months, after the date of availability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usually of 12 months, for the implementation of CE marking. At the end of this co-existence period, the national

8、standard(s) will be withdrawn. In the UK, there are no corresponding national standards. The UK as a member of CEN is obliged to publish EN 303-7:2006 as a British Standard. However, attention is drawn to the fact that during the development of this European standard, the UK consistently voted again

9、st its approval as a European standard. The reason for this disapproval and additional information is given in National Annex NA.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standa

10、rd cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Tue Apr 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 303-7October 2006ICS 91.140.10English VersionHeating

11、boilers - Part 7: Gas-fired central heating boilersequipped with a forced draught burner of nominal heat outputnot exceeding 1 000 kWChaudire de chauffage - Partie 7 : Chaudires dechauffage central quipes dun brleur air soufflutilisant les combustibles gazeux de puissance utileinfrieure ou gale 1 00

12、0 kWHeizkessel - Teil 7 : Zentralheizkessel fr gasfrmigeBrennstoffe mit einer Geblsebrenner mit einerNennwrmeleistung kleiner als oder gleich 1 000 kWThis European Standard was approved by CEN on 14 December 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipula

13、te the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists

14、in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of

15、 Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FO

16、R STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 303-7:2006: ELicensed Copy: Wang Bin, na, Tue Ap

17、r 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 303-7:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Constructional and operational requirements9 4.1 General principles9 4.2 Operational requirements .9 5 Test methods18 5.1 General princi

18、ples18 5.2 External tightness of the gas line 21 5.3 Heat input rates21 5.4 Gas pressure governor .22 5.5 Safety of operation 22 5.6 Control and safety equipments25 5.7 Combustion26 5.8 Useful efficiencies .27 5.9 Condensation.34 6 Marking and instructions 34 6.1 Marking .34 6.2 Instructions 36 6.3

19、Presentation .38 Annex A (informative) Diameters of combustion products evacuation ducts marketed in the various countries.49 Annex B (informative) Practical method of calibrating the test rig to enable determination of heat loss Dp.50 Annex C (informative) Determination of the heat losses from the

20、test rig of the indirect method and the contributions of the circulating pump of the test rig (see 5.8.2.3.1.3) .51 Annex D (informative) Determination of the operating time at full rate prior to modulation.52 Annex E (normative) Determination of the combustion characteristics Carbon monoxide and ni

21、trogen oxides 53 Annex F (normative) Case of a forced draught burner complying with EN 67655 Annex G (informative) Main symbols and abbreviations used.56 Annex H (informative) A-deviations.57 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisio

22、ns of EU Directives58 Bibliography 61 National Annex NA (informative) Additional information for UK users 62Licensed Copy: Wang Bin, na, Tue Apr 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 303-7:2006 (E) 3 Foreword This document (EN 303-7:2006) has been prepared by Technical Committee C

23、EN/TC 109 “Central heating boilers using gaseous fuels”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national standards sha

24、ll be withdrawn at the latest by April 2007. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which

25、 is an integral part of this document. WARNING Other requirements and other EU Directives may be applicable to the products falling within the scope of this European Standard. NOTE When constructional requirements for low temperature boilers will have been introduced in EN 303-1, they will replace t

26、hose of this European Standard by amendment. Annexes A, B, C, D, G and ZA are informative. Annexes E and F are normative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium

27、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Tue Ap

28、r 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 303-7:2006 (E) 4 1 Scope This European Standard specifies the requirements and test methods for the construction, the safety and the rational energy usage for gas-fired standard and low temperature central heating boilers equipped with a for

29、ced draught burner. These boilers comprise a boiler body and a forced draught gas burner brought together at the producers assembly facility, the whole being designed and marketed as a complete boiler. This standard does not apply to the case of the assembly of a boiler body and a forced draught gas

30、 burner designed and marketed separately. In this case, EN 303-3 applies. This European Standard applies to type B23boilers with a nominal heat output not exceeding 1000 kW with a water temperature at normal operation not exceeding 105 C and with a maximum water-side operating pressure not exceeding

31、 8 bar. This European Standard does not contain all the necessary requirements for: condensing boilers and combination boilers; boilers intended to be installed in the open; boilers permanently fitted with more than one flue outlet; boilers intended to be connected to a common flue having mechanical

32、 extraction; boilers equipped with several combustion chambers. This European Standard does not apply to living-space dedicated boilers (see 3.6). This European Standard only covers type testing. 2 Normative references The following referenced documents are indispensable for the application of this

33、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 303-1:1999, Heating boilers Part 1: Heating boilers with forced draught burners Terminology, general requirements, testing and

34、marking EN 437, Test gases Test pressures Appliance categories EN 676, Automatic forced draught burners for gaseous fuels EN 60335-1:2002, Household and similar electrical appliances - Safety Part 1: General requirements (IEC 60335-1:2001, modified) EN ISO 3166-1, Codes for the representation of nam

35、e of countries and their subdivisions Part 1: Country codes (ISO 3166-1:1997) CEN/TR 1749, European scheme for the classification of gas appliances according to the method of evacuation of the combustion products (types) Licensed Copy: Wang Bin, na, Tue Apr 03 07:10:06 GMT+00:00 2007, Uncontrolled C

36、opy, (c) BSIEN 303-7:2006 (E) 5 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 Gas rates 3.1.1 volumetric rate V (under test conditions); Vr (under reference conditions) volume of gas consumed by the boiler in unit time during conti

37、nuous operation NOTE Volumetric rate is expressed in cubic metres per hour (m3/h). 3.1.2 mass rate M (under test conditions); Mr(under reference conditions) mass of gas consumed by the boiler in unit time during continuous operation NOTE Mass rate is expressed in kilograms per hour (kg/h), or on occ

38、asions in grams per hour (g/h). 3.2 heat input Q product of the volumetric rate or the mass rate, and the net calorific value of the gas, under the same reference conditions NOTE Heat inputs are expressed in kilowatts (kW). 3.2.1 nominal heat input1)Qnheat input stated by the manufacturer 3.3 Output

39、s 3.3.1 useful output P quantity of heat transmitted to the heat carrier in unit time NOTE Outputs are expressed in kilowatts (kW) 3.3.2 nominal output Pnuseful output stated by the manufacturer 3.4 useful efficiency uratio of the useful output to the heat input NOTE the useful efficiency is express

40、ed in percent (%). 3.5 nominal voltage voltage or range of voltages stated by the manufacturer, at which the boiler can operate normally 1)Boilers fitted with a range-rating device operate at a nominal heat input between the maximum and minimum adjustable heat inputs. Modulating boilers operate betw

41、een the nominal heat input and the minimum controlled heat input. The maximum heat input corresponds to the nominal output of the boiler in accordance with EN 303-1. Licensed Copy: Wang Bin, na, Tue Apr 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 303-7:2006 (E) 6 3.6 boiler to be instal

42、led in the living space boiler with an effective rated output of less than 37 kW, designed to provide heat to the part of the living space in which it is installed by means of the emission of heat from the casing having an open expansion chamber, supplying hot water using gravity circulation 3.7 boi

43、ler appliance comprising a boiler body and a forced draught burner, designed and brought together at the producers assembly facility and marketed as a complete boiler 3.8 gases and categories gases are classified into families, groups and ranges in accordance with EN 437 Boilers are classified into

44、categories in accordance with EN 437. 3.9 Classification in accordance with the mode of evacuation of the combustion products (CEN/TR 1749) 3.9.1 type B appliance intended to be connected to a flue that evacuates the products of combustion to the outside of the room containing the appliance. The com

45、bustion air is drawn directly from the room 3.9.2 type B2type B appliance without draught diverter 3.9.3 type B23type B2appliance incorporating a fan upstream of the combustion chamber/heat exchanger 3.10 forced draught burner burner in which the combustion air is introduced by means of a fan 3.11 a

46、utomatic forced draught burner forced draught burner that is fitted with automatic ignition, flame monitoring and burner control devices. Ignition, flame monitoring and the on/off switching of the burner occur automatically. The heat input of the burner can be adjusted during operation either automa

47、tically or manually 3.12 total pre-mixed burner burner in which at least all the air theoretically required for complete combustion of the gas is mixed with the gas upstream of the mixture outlet ports 3.13 nozzle mixed burner burner in which part, or all, of the air theoretically required for combu

48、stion of the gas is mixed with the gas at, or downstream of, the air and gas ports 3.14 start gas rate gas rate ignited by the ignition device during the start-up of the burner Licensed Copy: Wang Bin, na, Tue Apr 03 07:10:06 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 303-7:2006 (E) 7 3.15 combust

49、ion chamber part of the boiler in which the combustion of the mixture of the gas and air takes place 3.16 gas line part of the burner which is made up of the valves and controls and safety devices in which gas is conveyed between the inlet connection and the burner head 3.17 range-rating device component on the burner intended to be used for adjusting the heat input, within a range of heat inputs stated by the manufacturer, to suit the actual heat requirements of the installation This adjustment may be progressive or in discrete steps. 3.1