BS EN 2898-2008 Aerospace series - Corrosion and heat resisting steel rivets - Technical specification《航空航天系列 耐腐蚀和热的钢制铆钉 技术规范》.pdf

《BS EN 2898-2008 Aerospace series - Corrosion and heat resisting steel rivets - Technical specification《航空航天系列 耐腐蚀和热的钢制铆钉 技术规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2898-2008 Aerospace series - Corrosion and heat resisting steel rivets - Technical specification《航空航天系列 耐腐蚀和热的钢制铆钉 技术规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 2898:2008Aerospace series Corrosion and heat resisting steel rivets Technical specificationICS 49.030.60g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60

2、g53g44g42g43g55g3g47g36g58BS EN 2898:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 62757 6National forewordThis British Standard is the UK implementation of EN 2898:2008.The UK participation in its p

3、reparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are respo

4、nsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2898March 2008ICS 49.030.60English VersionAerospace series - Corrosion and

5、heat resisting steel rivets -Technical specificationSrie arospatiale - Rivets en acier rsistant chaud et la corrosion - Spcification techniqueLuft- und Raumfahrt - Niete aus hochwarmfesten undkorrosionsbestndigen Sthlen - TechnischeLieferbedingungenThis European Standard was approved by CEN on 12 De

6、cember 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obt

7、ained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Managem

8、ent Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

9、Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by

10、any means reservedworldwide for CEN national Members.Ref. No. EN 2898:2008: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Required characteristics.5 5 Filing of documents.9 6 Certificate of conformity .9 BS EN 2898:20083 Foreword This document (EN 2898:20

11、08) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of

12、the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest b

13、y September 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stan

14、dards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, P

15、ortugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2898:20084 1 Scope This standard specifies the performance and test requirements for corrosion and heat resisting solid steel rivets intended for aerospace applications. It applies whenever it is specified

16、 in the document defining the rivet. Its use, after agreement between the customer and the supplier, for solid rivets made from other materials, requires determination, case by case, of the minimum tensile and double shear loads. 2 Normative references The following referenced documents are indispen

17、sable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by

18、 acceptance quality limit (AQL) for lot-by-lot inspection. EN 2002-001, Aerospace series Metallic materials Test methods Part 001: Tensile testing at ambient temperature. EN 2002-7, Aerospace series Metallic materials Test methods Part 7: Hardness test. 1)EN 2119, Aerospace series Heat resisting all

19、oy FE-PA2601 (X6NiCrTiMoV26-15) Solution treated and precipitation treated Wires for rivets 2 mm D 10 mm Rm 960 MPa. 1)EN 2470, Steel FE-PA11 Softened and cold drawn Wires for rivets 1 mm D 10 mm Aerospace series. 2)EN 3238, Aerospace series Metallic materials Test method Shear test for wires and ri

20、vets. 3)3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 batch for all tests, inspections and supplies, a batch of rivets is defined as follows: finished rivets of the same form, diameter and length, manufactured by the same process, made from

21、 one material, batch from the same heat treatment furnace with the same surface treatment, and deriving from the same wire coil and the same place of manufacture The maximum mass of each batch is limited to 25 kg. 1) Published as ASD Prestandard at the date of publication of this standard. 2) Publis

22、hed as ASD Standard at the date of publication of this standard 3) In preparation at the date of publication of this standard. BS EN 2898:20085 3.2 rivet wire samples for test, each rivet batch shall be accompanied by rivet wire samples taken from each end of the coil used to manufacture the batch.

23、The samples shall be submitted to the same heat treatment as the rivets of that batch 3.3 rivet samples rivet samples intended for tests shall be chosen at random from each batch 4 Required characteristics The rivets shall conform with the requirements of the document defining the rivet and those pr

24、escribed in Table 1. Inspections and tests are to be carried out by the rivet manufacturer. Table 1 Technical requirements and test methods Subclause Characteristics Technical requirements Inspection and test methods Number of samples 4.1 Materials Shall conform with the requirements of the material

25、 standard quoted in the document defining the rivet. See material specification. 4.2 Dimensions Shall conform with the requirements of the document defining the rivet. Methods are at manufacturers option. In case of dispute, the projection method at 25 magnification for diameter of up to 8 mm and 10

26、 for diameter above shall be used as a reference method. The inspection shall be carried out at three equidistant points around the rivet. Table 2 4.3 Heat treatment Shall conform with the condition of use defined in the material standard. See 4.5. 4.4 Surface treatment Shall be in conformity with t

27、he defining document. Methods are at manufacturers option. 4.5 Mechanical properties Shall be checked either by a double shear test or by a tensile test combined with a hardness test. 4.5.1 Double shear Non-assembled rivets (i.e. without post-formed head) shall conform with the values specified in T

28、able 4. See EN 3238. If the rivets are not long enough for the double shear test, it shall be carried out on the wire samples. Table 3 4.5.2 Tension Rivet wire samples shall conform with the values specified given in Table 5. See EN 2002-001. Table 3 continued BS EN 2898:20086 Table 1 Technical requ

29、irements and test methods (continued) Subclause Characteristics Technical requirements Inspection and test methods Number of samples 4.5.3 Hardness Hardness values for rivet wire samples shall conform with the requirements of the corresponding material standard. Hardness values for rivets shall corr

30、espond with the rivet hardness values within a tolerance of 5 %. See EN 2002-7. Table 3 4.5.4 Upset test After upset the head of the rivet shall be free from cracks or folds when viewed at a magnification of 10. Rivets shall be placed in a test fixture substantially conforming to Figure 1 a). The fr

31、ee end of the rivet shall be upset using a flat tool to obtain a head conforming to the requirements of Figure 1b). Table 3 This test to be performed only at the request of the purchaser 4.6 Surface condition, appearance Rivets shall be free from seams, burrs, laps, crevices, incrustations, clefts,

32、tooling marks, scores, cracks and other defect prejudicial to the use of the rivet. Rivets shall be examined visually with or without magnification. Magnification is limited to 6. Table 2 4.7 Identification and marking Each rivet shall be marked in conformity with the defining document, except for p

33、articular indications requested by the customer. No sharp edges or other defect detrimental to the correct set ting of the rivet shall be present. Visual examination. 4.8 Packaging Rivets shall be delivered in strong and durable packages, capable of protecting them from physical and corrosive deteri

34、oration. Any particular or additional packaging requirements shall be specified in the order. If the rivets delivered come from different batches, each batch shall be packed and identified separately. Unless particularly specified in the order, the number of rivets in the same package is left to the

35、 manufacturers discretion. However, maximum mass is 25 kg. A copy of the manufacturers delivery note relating to the rivet batch shall be included in the package but may, on the other hand, be sent separately on request. continued BS EN 2898:20087 Table 1 Technical requirements and test methods (con

36、cluded) Subclause Characteristics Technical requirements Inspection and test methods Number of samples 4.9 Labelling Durable external labels on the package shall contain the following information: Identity block of standard rivet; Quantity (mass or number of rivets); Customers order number; Manufact

37、urers identification, name and address; Number of manufacturers delivery note; Manufacturers batch number; Manufacturers Inspection stamp. Labels attached to a secondary package shall include the following information as a minimum: Identity block of the rivet; Quantity; Batch number; Inspection stam

38、p. Table 2 Sampling plan and acceptance level 4)non-destructive tests Number of rivets in batch Number of rivets to be sampled from batch Maximum number of defective rivets in sample allowing acceptance of batch a151 to 280 32 3 281 to 500 50 5 501 to 1 200 80 7 1 201 to 3 200 125 10 3 201 to 10 000

39、 200 14 10 001 to 35 000 315 21 35 001 to 150 000 500 21 aDefective rivets shall not be returned to the batch. 4) Sampling plan for normal inspection to ISO 2859-1 (AQL = 4 %). BS EN 2898:20088 Table 3 Sampling plan and scrap level destructive testing Number of rivets in batch Number of rivets to be

40、 sampled from batch Maximum number of defective rivets in sample resulting in scrapping of batch a151 to 280 5 1 281 to 500 5 1 501 to 1 200 5 1 1 201 to 3 200 8 1 3 201 to 10 000 8 1 10 001 to 35 000 8 1 35 001 to 150 000 13 1 aIf the reason for rejection results from the method of operating the te

41、st apparatus or from faulty heat treatment which can be rectified in a satisfactory manner, the tests may be repeated after elimination of the cause. A note to this effect shall be added to the corresponding inspection documents. Table 4 Shear strength Minimum breaking load in case of double shear N

42、 Nominal diameter of rivets mm EN 2470 Rc330 MPa EN 2119 Rc580 MPa 1,6 1 245 2 115 2,4 2 880 4 880 3,2 5 140 8 730 4,0 8 050 13 660 4,8 11 600 19 680 Table 5 Tensile strength Minimum tensile breaking load N Nominal diameter of rivets mm EN 2470 Rc450 MPa EN 2119 Rc960 MPa 1,6 850 1 810 2,4 1 950 4 1

43、80 3,2 3 510 7 480 4,0 5 490 11 700 4,8 7 910 18 870 BS EN 2898:20089 a) Before upset b) After upset Key 1 Test material hardness HRC 50-55 Figure 1 Upset test 5 Filing of documents For each batch the manufacturer shall keep documentation stating at least: relationship between the rivet wire materia

44、l batch and the rivet batch; a copy of the documents concerning the rivet wire material batch and the test references; heat treatment documents for the rivet batch; documents concerning the rivet batch inspections and tests; the final inspection certificate. These documents and all associated refere

45、nces shall be kept on file for at least three years and available for despatch to the customer, at his request, within that period. 6 Certificate of conformity The rivet manufacturer shall supply to the customer, no later than the delivery of the product, a final inspection certificate to confirm th

46、at the product conforms with all the requirements of this specification. BS EN 2898:2008BS EN 2898:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europ

47、e and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products

48、and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI of

49、fers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response t