BS EN 2862-2009 Aerospace series - Nuts anchor self-locking fixed 90 corner with counterbore in alloy steel cadmium plated MoS2 lubricated - Classification 1100 MPa (at ambient te.pdf

《BS EN 2862-2009 Aerospace series - Nuts anchor self-locking fixed 90 corner with counterbore in alloy steel cadmium plated MoS2 lubricated - Classification 1100 MPa (at ambient te.pdf》由会员分享，可在线阅读，更多相关《BS EN 2862-2009 Aerospace series - Nuts anchor self-locking fixed 90 corner with counterbore in alloy steel cadmium plated MoS2 lubricated - Classification 1100 MPa (at ambient te.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 2862:2009ICS 49.030.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Nuts, anchor,self-locking, fixed,90 corner, withcounterbore, in alloysteel, cadmium plated,MoS2 lubricated Classification : 1 100MPa (at ambienttemperature) / 235 CLicen

2、sed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 70134 4Amendments/corrigenda issued since publicationDate Comments

3、BS EN 2862:2009National forewordThis British Standard is the UK implementation of EN 2862:2009.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest

4、 to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/201

5、0 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2862 December 2009 ICS 49.030.30 English Version Aerospace series - Nuts, anchor, self-locking, fixed, 90 corner, with counterbore, in alloy steel, cadmium plated, MoS2lubricated - Classification :

6、 1 100 MPa (at ambient temperature) / 235 C Srie arospatiale - crous river, freinage interne, fixes, dangle 90, avec chambrage, en acier alli, cadmis, lubrifis MoS2- Classification : 1 100 MPa ( temprature ambiante) / 235 C Luft- und Raumfahrt - Annietmuttern, selbstsichernd, 90 Eckflansch, mit zyli

7、ndrischer Aussenkung, aus legiertem Stahl, verkadmet, MoS2-geschmiert - Klasse : 1 100 MPa (bei Raumtemperatur / 235 C This European Standard was approved by CEN on 29 September 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving

8、this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versio

9、ns (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,

10、Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STAN

11、DARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2862:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE C

12、HINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:2009EN 2862:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics .53.1 Configuration Dimensions Masses 53.2 Materials .53.3 Surface treatment 54 Designation 75 Marking .76 Technical speci

13、fication .7Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:2009EN 2862:2009 (E) 3 Foreword This document (EN 2862:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After en

14、quiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a natio

15、nal standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

16、ts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Cz

17、ech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA

18、 STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:2009EN 2862:2009 (E) 4 1 Scope This European Standard specifies the characteristics of 90 corner, counterbored, fixed, anchor nuts, with a self-locking feature achieved by forming the upper portion out-of-round, in alloy steel, cadmi

19、um plated, MoS2lubricated. Classification: 1 100 MPa 1) / 235 C. 2)2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

20、ment (including any amendments) applies. EN 2133, Aerospace series Cadmium plating of steels with specified tensile strength 1 450 MPa, copper, copper alloys and nickel alloys EN 2424:2008, Aerospace series Marking of aerospace products EN 2491, Aerospace series Molybdenum disulphide dry lubricants

21、Coating methods EN 2542, Aerospace series Steel FE-PL1502 (25CrMo4) Annealed Bar and wire De 40 mm For prevailing torque nuts EN 2543, Aerospace series Steel FE-PL1502 (25CrMo4) Annealed Sheet and strip 0,3 a 2 mm For prevailing torque nuts EN 9100, Quality Management Systems Requirements for Aviati

22、on, Space and Defense Organizations EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts ISO 3221, Aerospace Nuts, anchor, self-locking, fixed, 90 corner, with counterbore, with MJ threads, classifications: 1 100 MPa (at ambient temperature)/235 C

23、, 1 100 MPa (at ambient temperature)/315 C and 1 100 MPa (at ambient temperature)/425 C Dimensions ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts ISO 5858, Aerospace Nuts, self-locking, with maximum operating temperature less than or equal to 425 C Procurement specifica

24、tion ISO 8788, Aerospace Nuts, metric Tolerances of form and position TR 3791, Aerospace series Materials for self-locking nuts, threaded inserts and screw thread inserts of temperature classes 425 C 3) 1) Corresponds to strength class of the associated bolt, the 100 % load of which it is able to wi

25、thstand, when tested at ambient temperature, without breaking or cracking. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the surface treatm

26、ent. 3) Published as ASD-STAN Technical Report at the date of publication of this standard. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:2009EN 2862:2009 (E) 5 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1

27、 and Table 1. Dimensions and tolerances are in conformity with ISO 3221, expressed in millimetres and apply after surface treatment but before MoS2lubrication. Form and position tolerances shall be in conformity with ISO 8788. 3.2 Materials EN 2542, EN 2543 or TR 3791. 3.3 Surface treatment EN 2133,

28、 5 m minimum on threads and all surfaces which can be contacted by a 20 mm diameter ball. On all other surfaces a continuous deposit shall be present, plus EN 2491, thickness not specified. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:

29、2009EN 2862:2009 (E) 6 These values in micrometres apply before surface treatment. They do not apply tothreads and sheared edges the surface texture of which will be as achieved by usualmanufacturing methods. Remove sharp edges 0,1 to 0,4. Key 1 Marking 2 Form out-of-round in this area to achieve se

30、lf-locking. Tooling marks are permitted in this area. 3 Thread 4 Radius or chamfer 5 Seating plane Figure 1 Table 1 Diameter code Thread a E F G H Jb K L M Nc R S V Mass kg/1 000piecesapprox. min. min. max. max. max. max. max. 0,25 030 MJ30,5-4H6H 6 8,5 d d4,6 3 11,7 3,2 1 2,5 2,5 4,80,5 040 MJ40,7-

31、4H6H 8,5 12 4,4 2,2 6,2 4 15,7 5,8 3 1,1 050 MJ50,8-4H6H 9,5 13,4 5,5 2,4 7,3 4,5 17,2 6,9 1,4 060 MJ61-4H5H 11 15,6 6,5 2,7 8,7 5 19,7 8,1 1,2 3,5 2,2 080 MJ81-4H5H 8,5 10,9 6,5 21,2 9,9 1,5 3 5,7 4,6 100 MJ101,25-4H5H 13 18,4 10,5 3 12,9 8,1 25,8 12 1,6 4,5 3,5 6,6 7,8 aIn accordance with ISO 5855

32、-2. In the self-locking zone, the tolerances apply before forming out-of-round. bIs to sharp corners (chamfered) or point of tangency (radiused). cIs applicable at the rivet hole location. dDiameter code 030 does not have a counterbore. 6,3 3,2 Alternatives: countersunk rivet holes (when specified b

33、y purchaser) may be dimpled or cut countersunk (at manufacturers option). Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN 2862:2009EN 2862:2009 (E) 7 4 Designation EXAMPLE Description block NUT Identity block EN2862060 Number of this standard

34、Code (see Table 2) Diameter code (see Table 1) NOTE If necessary the originator code I9005 should be placed between the description block and the identity block. Table 2 Option Code Plain rivet holes (hyphen) Dimpled or countersunk rivet holes K 5 Marking EN 2424:2008, style N. See Figure 1. 6 Techn

35、ical specification ISO 5858 except for: Approval of manufacturers: see EN 9100; Qualification of products: see EN 9133. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSIBS EN2862:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +

36、44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updat

37、ed by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Stand

38、ard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the

39、latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website htt

40、p:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards thr

41、ough its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up t

42、o date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via Briti

43、sh StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyrig

44、ht, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standa

45、rd,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:34, Uncontrolled Copy, (c) BSI