BS EN 2596-2006 Aerospace series Washers lock with radial serrations in corrosion resisting steel cadmium plated for flight control rods Dimensions《航空航天系列 耐蚀钢制的镀镉径向锯齿锁紧垫圈规范 尺寸规格》.pdf

《BS EN 2596-2006 Aerospace series Washers lock with radial serrations in corrosion resisting steel cadmium plated for flight control rods Dimensions《航空航天系列 耐蚀钢制的镀镉径向锯齿锁紧垫圈规范 尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2596-2006 Aerospace series Washers lock with radial serrations in corrosion resisting steel cadmium plated for flight control rods Dimensions《航空航天系列 耐蚀钢制的镀镉径向锯齿锁紧垫圈规范 尺寸规格》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 2596:2006Aerospace series Washers, lock, with radial serrations in corrosion resisting steel, cadmium plated for flight control rods DimensionsLicensed Copy: Wang Bin, ISO/

2、EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:2006 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 2596:2006. Itsupersedes BS EN 2596:1990 which is withdrawn.The UK Technical Committee draws the attention of the user, tothe fac

3、t that under normative references, the quality managementsystems Standard applicable to BS EN 2596, is EN 9133 and not EN9100, as is the case for all other EN standards for radial serrated lockwashers. This error has been identified to CEN but no corrigendahas been issued to date. It is expected to

4、be corrected at the nextamendment or revision of the European Standard.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can beobtained on request to its secretary.This p

5、ublication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 55899 3ICS 49.030.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the

6、 authority of theStandards Policy and Strategy Committee on 28 February 2011.Amendments issued since publicationDate Text affectedLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:2006EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2596Ma

7、y 2006ICS 49.060 Supersedes EN 2596:1988 English VersionAerospace series - Washers, lock, with radial serrations incorrosion resisting steel, cadmium plated for flight control rods -DimensionsSrie arospatiale - Freins stries radiales en acierrsistant la corrosion, cadmis pour bielles decommandes de

8、vol - DimensionsLuft- und Raumfahrt - Sicherungen, radialverzahnt auskorrosionsbestndigem Stahl, verkadmet frBediengestnge von Flugsteuerungen - MaeThis European Standard was approved by CEN on 6 January 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate t

9、he conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in t

10、hree official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Aus

11、tria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR ST

12、ANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2596:2006: ELicensed Copy: Wang Bin, ISO/EXCHANGE CH

13、INA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:2006BS EN 2596:2006EN 2596:2006 (E) 2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Required characteristics 4 4 Designation .6 5 Marking 7 6 Qualification 7 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS,

14、 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:2006BS EN 2596:2006EN 2596:2006 (E) 3 Foreword This European Standard (EN 2596:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance wi

15、th the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an id

16、entical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be

17、held responsible for identifying any or all such patent rights. This European Standard supersedes EN 2596:1988. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,

18、Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHI

19、NA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:20064 1 Scope This standard specifies the characteristics of lock washers in corrosion resisting steel, cadmium plated, with radial serrations primarily intended for flight control rods. These lock washers are intended to immobilis

20、e the rod end in relation to the rod body, whilst allowing a precise positional adjustment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest editi

21、on of the referenced document (including any amendments) applies. EN 2133, Aerospace series Cadmium plating of steels with specified tensile strength 1 450 MPa, copper, copper alloys and nickel alloys. EN 2538, Aerospace series Steel FE-PM3801 (X5CrNiCu17-4) Air melted Solution treated and precipita

22、tion treated Sheet and strip a 6 mm Rm 1 310 MPa. 1)EN 2540, Aerospace series Steel FE-PM3902 (X7CrNiAl17-7) Air Melted Solution treated and precipitation hardened Sheet and strip a 6 mm 1 240 MPa Rm 1 450 MPa. 1)EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:20

23、00) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994). 3 Required characteristics 3.1 Dimensions Mass Configuration shall correspond with Figures 1, 2 and 3. The dimensions and masses shall conform with values quot

24、ed in Tables 1 and 2. Dimensions apply after cadmium plating. 3.2 Surface roughness Ra= 3,2 m. This value applies prior to cadmium plating. 3.3 Material Steel according to EN 2540 or EN 2538 (inactive for new design). 3.4 Surface treatment Cadmium plated according to EN 2133, 10 m to 20 m, without c

25、hromatation. 1) Published as AECMA Prestandard at the date of publication of this standard. BS EN 2596:2006EN 2596:2006 (E) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:20065 Dimensions in millimetres Dimensions in millimetres aN equid

26、istant serrations bR 0,5 to 0,8 cR 0,3 to 0,5 dIdentification mark aN equidistant serrations bR 0,5 to 0,8 cR 0,3 to 0,4 dIdentification mark Figure 1 Element for rod body side Code A Figure 2 Element for rod end side Code B Figure 3 Thickness of lock washer assembly BS EN 2596:2006EN 2596:2006 (E)

27、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:20066 Table 1 Dimensions in millimetres d1d2d3a1a2a3a4(a5) b1b2l1l2l3r1r2Diameter code 0,1 + 0,5 0 0,25 0,15 + 0,15 0,25 0,15 0,15 0,15 0,15 0,25 0,25 0 0,15 0,15 0,1508 8,2 12,7 0,58 1,1 1,

28、8 0,5 1,3 1,3 8,4 4,0 6,8 0,7010 10,2 1,0 8,3 12 12,2 19,0 1,6 1,2 2,0 2,0 2,0 12,0 6,5 10,5 14 14,2 22,0 0,80 1,4 0,6 2,9 2,9 13,0 8,8 12,5 2,4 2,0016 16,3 25,4 1,8 0,86 1,5 1,6 2,3 0,7 3,0 3,0 14,7 10,0 14,0 2,7 1,45Table 2 a1 + a4Mass lock washer assembly mm g Diameter code N Number of serrations

29、 min. max. 0,3 08 42 8721 8821 2,38 1,8 10 6,0 12 50 8742 8842 2,80 4,5 14 3,10 5,8 16 56 8920 90 3,16 9,6 4 Designation EXAMPLE Description block WASHER LOCK Identity block EN2596A08 Number of this standard Code for the lock washer (see Table 3) Diameter code (see Table 1) NOTE If necessary, the co

30、de I9005 shall be placed between the description block and the identity block. BS EN 2596:2006EN 2596:2006 (E) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBS EN 2596:20067 Table 3 Lock washer Code Element, rod body side, according to Figure 1 A

31、Element, rod end side, according to Figure 2 B Lock washer assembly C 5 Marking In addition to the manufacturers own marking, each lock washer and its packaging shall be marked, using the identity block as defined in Clause 4 of this standard. The marking position and method are at the manufacturers

32、 option. The marking, when it is possible, shall be indelible and shall not impair the characteristics of the lock washer. 6 Qualification According to EN 9100. BS EN 2596:2006EN 2596:2006 (E) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIThis pag

33、e deliberately left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIThis page deliberately left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSIBSI is the independent national body respons

34、ible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquart

35、ers389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products a

36、nd serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers

37、 Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BS

38、I Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of

39、 those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electroni

40、c information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For detail

41、s of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists

42、 in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any me

43、ans electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 26/05/2011 08:51, Uncontrolled Copy, (c) BSI