BS EN 2591-225-2007 Aerospace series - nElements of electrical nand optical nconnection - nTest methods - nPart 225 RF high potential nwithstanding voltage《航空航天系列 电气和光学连接元件 试验方法 第2.pdf

《BS EN 2591-225-2007 Aerospace series - nElements of electrical nand optical nconnection - nTest methods - nPart 225 RF high potential nwithstanding voltage《航空航天系列 电气和光学连接元件 试验方法 第2.pdf》由会员分享，可在线阅读，更多相关《BS EN 2591-225-2007 Aerospace series - nElements of electrical nand optical nconnection - nTest methods - nPart 225 RF high potential nwithstanding voltage《航空航天系列 电气和光学连接元件 试验方法 第2.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58c

2、onnection Test methods Part 225: RF high potential withstanding voltageICS 49.060Aerospace series Elements of electrical and optical BRITISH STANDARDBS EN 2591-225:2007BS EN 2591-225:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSIThis British S

3、tandard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 56479 6Amendments/corrigenda issued since publicationDate Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot

4、confer immunity from legal obligations. National forewordThis British Standard is the UK implementation of EN 2591-225:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/3, Aerospace Conne

5、ctors.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2591-225December 2007ICS 49.060English VersionAerospace series - El

6、ements of electrical and optical connection- Test methods - Part 225: RF high potential withstandingvoltageSrie arospatiale - Organes de connexion lectrique etoptique - Mthodes dessais - Partie 225: Tenue en hautetension HFLuft- und Raumfahrt - Elektrische und optischeVerbindungselemente - Prfverfah

7、ren - Teil 225: HF-HochspannungsfestigkeitThis European Standard was approved by CEN on 27 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up

8、-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunde

9、r the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hun

10、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: r

11、ue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2591-225:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSI2 Contents Page Foreword3 1 Sc

12、ope 4 2 Normative references 4 3 Preparation of specimens.4 4 Apparatus .4 5 Method 5 6 Results5 EN 2591-225:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSI3 Foreword This document (EN 2591-225:2007) has been prepared by the Aerospace and Defen

13、ce Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presen

14、tation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility th

15、at some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound t

16、o implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switz

17、erland and the United Kingdom. EN 2591-225:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies a test method to test a mated pair of connectors under RF high potential withstanding voltage. It shall be use together

18、with EN 2591-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-

19、100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 4604-002, Aerospace series Cable, electrical, for signal transmission Part 002: General. 3 Preparation of specimens The connectors shall be wired with an approximately 50 mm of the dedicated coaxia

20、l cable as per EN 4604-002. This assembly shall then be inserted into the high impedance circuit as shown on Figure 1. 4 Apparatus An RF power source up to 11 GHz frequency. An RF transformer with a variable output. RF voltmeter and RF ammeter. EN 2591-225:2007Licensed Copy: Wang Bin, ISO/EXCHANGE C

21、HINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSI5 Key 1 Connectors under test 2 RF V 3 RF A 4 RF power source 5 Transformer 6 Variable capacity Figure 1 Circuit diagram 5 Method The sample shall be instantaneously subjected to the RF voltage and frequency specified in the product standar

22、d, between the centre contacts and the conductive housing of the connectors. Duration of test shall be one minute (1 min). The frequency source shall be stabilised and have a very good form factor of sine wave output. 6 Results No breakdown shall occur and leakage current shall be less than the maxi

23、mum specified in the product standard. 1 5 4 63 2EN 2591-225:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSIBS EN BSILicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/05/2008 02:03, Uncontrolled Copy, (c) BSI389 Chiswick High RoadLondon

24、W4 4AL2591-225:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment

25、 or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would i

26、nform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest e

27、ditions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response t

28、o orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Li

29、brary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are ke

30、pt up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to

31、British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization

32、 bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the f

33、ree use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.