BS EN 2358-1989 Specification for eye-ends in corrosion resisting steel swaged on type control cable Dimensions and loads《操纵钢索的旋锻耐蚀钢孔眼端头规范 尺寸和负荷》.pdf

《BS EN 2358-1989 Specification for eye-ends in corrosion resisting steel swaged on type control cable Dimensions and loads《操纵钢索的旋锻耐蚀钢孔眼端头规范 尺寸和负荷》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2358-1989 Specification for eye-ends in corrosion resisting steel swaged on type control cable Dimensions and loads《操纵钢索的旋锻耐蚀钢孔眼端头规范 尺寸和负荷》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2358:1989 Specification for Eye-ends in corrosion resisting steel swaged on type, control cable Dimensions and loads This European Standard EN2358 has the status of a British Standard. UDC 629.7.05:621.854:621.85.052.004.1BSEN2358:1989 This British Standard, h

2、aving been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 29September1989 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment 8

3、8/70402 DC ISBN 0 580 17622 3 Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisches Normungsinstitut Belg

4、ium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Ireland National Standards Authority of Ireland It

5、aly Ente Nazionale Italiano di Unificazione Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus de Qualidade Spain Instituto Espaol de Normalizacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisatio

6、n UnitedKingdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBSEN2358:1989 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2358 3 National appendix A Inside back cover Nationa

7、l appendix B Inside back coverBSEN2358:1989 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2358“Aerospace series. Eye-ends in corrosion resisting steel swaged on type, c

8、ontrol cable. Dimensions and loads”, published by the European Committee for Standardization (CEN). EN2358 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of Bri

9、tish Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back co

10、ver and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2358 September 1988 UDC 629.7.05:621.854:621.85.052.004.1 K

11、ey words: Aircraft industry, flight control, flexible cable, cable-end, crimping end piece, dimensions, breaking loads. English version Aerospace series Eye-ends in corrosion resisting steel swaged on type, control cable Dimensions and loads Srie arospatiale Embouts il en acier rsistant la corrosion

12、 sertir sur cbles de commandes Dimensionsetcharges Luft- und Raumfahrt Seilschuhe mit se aus korrosionsbestndigem Stahl zumAufquetschen auf Steuerseile Mae undBelastungen This European Standard was accepted by CEN on1988-03-17. CEN members are bound to comply with the requirements of CEN Internal Re

13、gulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member.

14、This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as the official versions. CEN members are

15、 the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung

16、Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN 1988 Copyright reserved to all CEN members Ref. No. EN 2358:1988 EEN2358:1988 BSI 01-2000 2 Brief history This draft European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and vo

17、tes carried out in accordance with the rules of this Association, this draft has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. In accordance with the Common CEN/CENELEC Rules, the followin

18、g countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Contents Page Brief history 2 1 Scope and field of application 3 2 References 3 3 Requi

19、red characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 Figure 4 Table 5EN2358:1988 BSI 01-2000 3 1 Scope and field of application This standard specifies the characteristics of corrosion resisting steel eye-ends suitable for swaging on to aircraft control cables. 2 References

20、ISO 2020, Aerospace Mechanical system parts Preformed flexible steel wire rope for aircraft controls Technical specification. EN 2465, Steel FE-PA 11 Softened Bars D e 100mm Aerospace series. EN 2516, Aerospace series Passivation of corrosion resistant steels 1) . EN 2569, Aerospace series Control c

21、able fittings and turnbarrel assemblies Technical Specification 1) . 3 Required characteristics 3.1 Dimensions Tolerances Loads Mass The configuration shall correspond to the figure and the dimensions shall conform to the values given in the Figure and theTable. 3.2 Surface roughness SeeFigure. 3.3

22、Material Steel EN 2465. 3.4 Surface treatment Passivation EN 2516. 1) In preparationEN 2358:1988 4 BSI 01-2000 Figure EN 2358:1988 BSI 01-2000 5 Table Dimensions in millimetres Cable A C D E F G J L N P Q R T t Mass g Minimum breaking load kN a Code Nominal diameter H 11 H 8 0,5 0,5 16 1,6 2,4 5 10

23、1 11 13 4,06 37 1,98 2,3 3,50 3 21 0,04 4,3 2,15 24 2,4 2,9 12 15,5 18 5,54 45 2,77 3 4,83 25 0,05 9 4,45 32 3,2 4,9 6 14 16 19 6,35 53 3,58 3,9 5,56 5 31 0,08 15,2 8,90 40 4 17 17,5 21 7,54 61 4,37 4,8 6,35 37 25,9 12,45 48 4,8 6,4 8 20 1,5 18,5 23 9,12 66 5,15 5,7 7,95 6 40 0,10 37,6 18,60 56 5,6

24、7,4 23 20 25 10,84 72 5,94 6,6 9,52 8 44 60,5 24,90 64 6,4 7,9 10 25 23,5 29 12,55 79 6,73 7,4 11,12 47 81,7 31,20 a Equal to the one of the cable used according to ISO 2020. +0,60 0,25 +0,25 0 0 0,12 +0,5 0 +0,12 0 +0,25 0 +1,0 0 +0,8 0 0 0,12 0 0,18EN2358:1988 6 BSI 01-2000 4 Designation Each eye-

25、end for swaging on to cables shall only be designated as in the following example: NOTEIf necessary, originator code S9005 may be introduced between the description block and identity block. 5 Marking In addition to the manufacturers own marking, each eye-end for swaging on to cables shall be marked

26、 (seeFigure) using the identity block as defined in clause4 of this standard. The marking method is at the manufacturers option. 6 Technical specification The eye-ends for swaging on to cables supplied according to this standard shall conform with the requirements of EN2569.BSEN2358:1989 BSI 01-2000

27、 National appendix A The UnitedKingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civil Av

28、iation Authority (Airworthiness Division) Federation of Wire Rope Manufacturers of Great Britain Ministry of Defence Society of British Aerospace Companies Limited Stainless Steel Wire Export Group National appendix B The British Standards corresponding to the European and International Standards re

29、ferred to in the text are identical in number and title with those given in clause2 with the exception of ISO2020 for which the related British Standard is British Standard W13.BS EN 2358:1989 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national bod

30、y responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest a

31、mendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be

32、 found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publicatio

33、ns should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides

34、 a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:0208

35、9967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright

36、subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or b

37、y any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.