BS EN 2353-1989 Specification for turnbarrels control cable in corrosion resisting steel Dimensions and loads《耐蚀钢操纵钢索转动圆套筒的规范 尺寸和负荷》.pdf

《BS EN 2353-1989 Specification for turnbarrels control cable in corrosion resisting steel Dimensions and loads《耐蚀钢操纵钢索转动圆套筒的规范 尺寸和负荷》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2353-1989 Specification for turnbarrels control cable in corrosion resisting steel Dimensions and loads《耐蚀钢操纵钢索转动圆套筒的规范 尺寸和负荷》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2353:1989 Specification for Turnbarrels, control cable in corrosion resisting steel Dimensionsandloads This European Standard EN2353 has the status of a British Standard. UDC 629.7.05:621.854:621.85.052.004.1:669.14.018.89BSEN2353:1989 This British Standard, h

2、aving been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 31October1989 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment 88/

3、70402 DC ISBN 0 580 17725 4 Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisches Normungsinstitut Belgiu

4、m Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Ireland National Standards Authority of Ireland Ital

5、y Ente Nazionale Italiano di Unificazione Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Instituto Espaol de Normalizacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation

6、United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBSEN2353:1989 BSI 12-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2353 3 National appendix A Inside back cover National

7、 appendix B Inside back coverBSEN2353:1989 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2353 “Aerospace series. Turnbarrels, control cable in corrosion resisting steel

8、. Dimensions and loads”, published by the European Committee for Standardization (CEN). EN2353 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standar

9、ds are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back cover and a ba

10、ck cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2353 September 1988 UDC: 629.7.05:621.854:621.85.052.004.1:669.14.018.8

11、9 Key words: Aircraft industry, flight control, flexible cable, cable tensioner, joining adaptor, corrosion resisting steel, dimensions, breaking loads. English version Aerospace series Turnbarrels,controlcable incorrosionresistingsteel Dimensions and loads Srie arospatiale Douilles de tendeurs en a

12、cier rsistant la corrosion Dimensions et charges Luft- und Raumfahrt Spannschlomuttern aus korrosionsbestndigem Stahl Mae und Belastungen This European Standard was accepted by CEN on 1988-03-17. CEN members are bound to comply with the requirements of CEN Internal Regulations which stipulate the co

13、nditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard exists in

14、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as the official versions. CEN members are the national standards organiza

15、tions of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Sta

16、ssart 36, B-1050 Brussels CEN 1988 Copyright reserved to all CEN members Ref. No. EN 2353:1988 EEN2353:1988 BSI 12-1999 2 Brief history This draft European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance w

17、ith the rules of this Association, this draft has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. In accordance with the Common CEN/CENELEC Rules, the following countries are bound to Implem

18、ent this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Contents Page Brief history 2 1 Scope and field of application 3 2 References 3 3 Required characteristics 3 4 Designa

19、tion 6 5 Marking 6 6 Technical specification 6 Figure 4 Table 5EN2353:1988 BSI 12-1999 3 1 Scope and field of application This standard specifies the characteristics of turnbarrels in corrosion resisting steel intended for aircraft control cables. 2 References ISO 2020, Aerospace Mechanical system p

20、arts Preformed flexible steel wire rope for aircraft controls Technical specification. ISO 5855-1, Aerospace construction MJ threads Part 1: Basic profile. ISO 5855-2, Aerospace construction MJ threads Part 2: Dimensions for bolts and nuts. EN 2363, Aerospace series Locking clips for turnbuckles of

21、control cables Dimensions. EN 2462, Steel FE-PA13 Softened Bars D e 100 mm Aerospace series. EN 2516, Aerospace series Passivation of corrosion resistant steels 1) . EN 2569, Aerospace series Control cable fittings and turnbarrel assemblies Technical specification 1) . 3 Required characteristics 3.1

22、 Dimensions Tolerances Loads Mass The configuration shall correspond to the Figure and the dimensions shall conform to the values given in the Figure and the Table. 3.2 Surface roughness See Figure. 3.3 Material Steel EN 2462. 3.4 Surface treatment Passivation EN 2516. 1) In preparation.EN 2353:1988

23、 4 BSI 12-1999 Figure EN 2353:1988 BSI 12-1999 5 Table Dimensions in millimetres Thread a B D H J K L M Q T Mass Minimum breaking load kN b Nominal diameter of cable used Code Designation 0,1 max. min. 0,8 0,1 min. Code Dimensions 0,5 max. min. 0 0,3 0,25 g 04 MJ 4 0,70 4H6H 7 4,78 4,18 4 5,5 27 S 5

24、8 4,45 4,35 5,2 8 5,3 2,15 1,6 05 MJ 5 0,80 4H6H 8 5,80 5,20 5 6,8 S 5,49 5,29 6,2 9,4 4,45 2,4 49 L 102 14,2 06 MJ 6 1,00 4H5H 10 7,04 6,24 6 8,5 27 S 58 6,36 6,16 7,5 18,3 8,90 3,2 49 L 102 28 07 MJ 7 1,00 4H5H 11 8,04 7,24 7 9,8 27 S 58 7,36 7,16 8,8 26,3 12,45 4 49 L 102 40,1 08 MJ 8 1,00 4H5H 1

25、2 9,04 8,24 8 11,5 26,5 S 58 8,36 8,16 10,5 10 41,4 18,60 4,8 10 MJ 10 1,25 4H5H 14 11,08 10,28 10 13,5 48 S 102 10,20 10 12 69 24,90 5,6 12 MJ 12 1,25 4H5H 17 12,09 12,29 12 15,8 S 12,20 12 14 89,3 31,20 6,4 a Conforming to ISO 5855-1 and ISO 5855-2. b Equal to the one of the cable used according t

26、o ISO 2020.EN2353:1988 6 BSI 12-1999 4 Designation Each turnbarrel shall only be designated as in the following example: NOTEIf necessary, the originators code S9005 may be introduced between the description block and the identity block. 5 Marking In addition to the manufacturers own marking, each t

27、urnbarrel shall be marked (seeFigure) using the identity block as defined in clause4 of this standard. The marking method is to the manufacturers option. 6 Technical specification The turnbarrels supplied according to this standard shall conform with the requirements of EN2569.BSEN2353:1989 BSI 12-1

28、999 National appendix A The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civi

29、l Aviation Authority (Airworthiness Division) Federation of Wire Rope Manufacturers of Great Britain Ministry of Defence Society of British Aerospace Companies Ltd. Stainless Steel Wire Export Group National appendix B The British Standards corresponding to the European and International Standards r

30、eferred to in the text are identical in number and title to those given in clause 2 with the exception of ISO2020, ISO5855-1 andISO5855-2 for which the corresponding British Standards are British Standard W13 (related), BS6293-1 (identical) and BS6293-2 (identical) respectively.BS EN 2353:1989 BSI 3

31、89 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updat

32、ed by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishSt

33、andard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest edit

34、ions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have

35、 been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also a

36、vailable which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and ot

37、her benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Paten

38、ts Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary

39、details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.