BS EN 1343-2012 Kerbs of natural stone for external paving Requirements and test methods《室外铺路用天然路边石 要求和试验方法》.pdf

《BS EN 1343-2012 Kerbs of natural stone for external paving Requirements and test methods《室外铺路用天然路边石 要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1343-2012 Kerbs of natural stone for external paving Requirements and test methods《室外铺路用天然路边石 要求和试验方法》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 1343:2012Kerbs of natural stonefor external paving Requirements and testmethodsCopyright European Committee for Standardization Provided by IHS under license with CENNot fo

2、r ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1343:2012. Itsupersedes BS EN 1343:2001 which is withdrawn.The UK participation in its preparation was entrusted to Techn

3、icalCommittee B/507, Paving units and kerbs.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards

4、 Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 63841 1ICS 93.080.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2013.Amendm

5、ents issued since publicationDate Text affectedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1343 November 2

6、012 ICS 93.080.20 Supersedes EN 1343:2001English Version Kerbs of natural stone for external paving - Requirements and test methods Bordures de pierre naturelle pour le pavage extrieur - Exigences et mthodes dessai Bordsteine aus Naturstein fr Auenbereiche - Anforderungen und Prfverfahren This Europ

7、ean Standard was approved by CEN on 6 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references con

8、cerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member i

9、nto its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

10、 Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMIT

11、EE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1343:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for Resa

12、leNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 2 Contents Page Foreword 41 Scope 52 Normative references 53 Terms and definitions .54 Requirements and test methods for slabs of natural stone 94.1 Introduction 94.1.1 General 94.1.2 Denomination

13、.94.1.3 Alteration of physical properties of the natural stone .94.2 Dimensions .94.2.1 Overall width and height .94.2.2 Batter 114.2.3 Tolerances of faces (straight kerbs only) 114.2.4 Curved kerbs . 114.2.5 Face irregularities . 114.3 Freeze/thaw resistance 124.3.1 Freeze- thaw under normal condit

14、ions . 124.3.2 Freeze-thaw in the presence of de-icing salts . 124.4 Breaking strength Flexural strength 124.5 Appearance . 124.5.1 General . 124.5.2 Reference sample, visual inspection and acceptance criteria 124.6 Water absorption 134.7 Apparent density and open porosity 134.8 Petrographic descrip

15、tion . 134.9 Dangerous substances 135 Evaluation of conformity 145.1 General . 145.2 Initial type testing (ITT) and Type Testing (TT) 145.3 Factory Production Control . 156 Marking, labelling and packaging . 18Annex A (informative) Calculation of height for kerbs for kerbs with a square cross sectio

16、n 19Annex B (informative) Guidance on sampling 20B.1 General . 20B.2 Principles of sampling . 20B.3 Taking bulk samples 20B.4 Preparing a sampling plan . 20B.5 Sampling apparatus . 21B.6 Sampling methods 21B.6.1 General . 21B.6.2 Sampling from quarries . 21B.6.3 Sampling from production units and co

17、nsignments 22B.6.4 Sampling from construction works 22B.7 Marking, packaging and dispatch of the samples . 22B.8 Sampling report 22Annex C (informative) Example of calculation of Lower Expected Value 24C.1 Scope . 24Copyright European Committee for Standardization Provided by IHS under license with

18、CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 3 C.2 Symbols and definitions . 24C.3 Calculation of Lower Expected Value . 24Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Constructio

19、n Products Directives . 27ZA.1 Scope and relevant characteristics . 27ZA.2 Procedure for the attestation of conformity of kerbs of natural stone 28ZA.2.1 System of attestation of conformity 28ZA.2.2 EC declaration of conformity . 29ZA.3 CE marking and labelling . 29Bibliography 31Copyright European

20、Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 4 Foreword This document (EN 1343:2012) has been prepared by Technical Committee CEN/TC 178 “Paving units and kerbs”,

21、 the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by August 2014. Attention is

22、 drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1343:2001. This document has been prepared under a mandate given to CE

23、N by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The following changes have been made in this new edition: a) Wher

24、e possible the requirements refer to separate test methods prepared by CEN/TC 246, “Natural stones“. The change was made to allow those placing the products on the market to use the same test results for a number of products. b) The values to be declared have been clarified and where applicable the

25、declared values are now lower expected values. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, For

26、mer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Copyright European Committee for Standar

27、dization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 5 1 Scope This European Standard specifies the performance requirements and the corresponding test methods for all natural stone kerbs use

28、d for external paving and road finishes. External paving use includes all pavements typical of road works, such as pedestrian and trafficked areas, outdoor squares and similar to be used in an outdoor condition that are subject to the weathering agents, such as temperature changes, rain, ice, wind,

29、etc. This European Standard provides also for the evaluation of conformity and for marking of the natural stone slabs. This European Standard also covers characteristics that are of importance to the trade. 2 Normative references The following documents, in whole or in part, are normatively referenc

30、ed in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1936, Natural stone test methods Determination of real density and apparen

31、t density, and of total and open porosity EN 12371, Natural stone test methods Determination of frost resistance EN 12372, Natural stone test methods Determination of flexural strength under concentrated load EN 12407, Natural stone test methods Petrographic examination EN 12440, Natural stone Denom

32、ination criteria EN 13373:2003, Natural stone test methods Determination of geometric characteristics on units EN 13755, Natural stone test methods Determination of water absorption at atmospheric pressure 3 Terms and definitions For the purposes of this document, the following terms and definitions

33、 apply. 3.1 kerb unit greater than 300 mm in length, commonly used as edging to a road or footpath Note 1 to entry: See Figure 1. 3.1.1 curved concave kerb kerb, curved in plan with a concave face 3.1.2 curved convex kerb kerb, curved in plan with a convex face Copyright European Committee for Stand

34、ardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 6 3.2 upper face horizontal surface of a kerb intended to be seen when in use 3.3 bed face surface of a kerb intended to be in contact w

35、ith the bedding material when in use 3.4 front face vertical traffic face of the kerb 3.5 rear face vertical and facing away from the traffic (probably in contact with the ground) 3.6 actual dimension dimension of a kerb as measured 3.7 work dimension size of a kerb as specified 3.8 overall length l

36、ength of a kerb measured on the visible face Note 1 to entry: See Figure 2. 3.9 overall width shorter side of the rectangle with the smallest area able to enclose the kerb Note 1 to entry: This only applies to straight kerbs. The overall width of a curved kerb is the widest point of the cross-sectio

37、n of the kerb (see Figure 2). 3.10 height distance between the upper face and the bed face of the kerb 3.11 batter intended deviation from the vertical of the traffic face of a kerb 3.12 textured kerb with a surface finish produced by secondary processing, from a saw or hewn surface 3.13 fine textur

38、ed surface finish with a maximum difference of 1,0 mm between peaks and depressions (for example, polished, honed or sawn with a diamond disc or blade) 3.14 coarse textured surface finish with more than 1,0 mm difference between peaks and depressions (for example, dolly pointed, shot blasted or flam

39、e textured) Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 7 3.15 hewn kerb with a natural surface finish which has not subjected to secondary pr

40、ocessing, for example a riven or split face 3.16 tooled finish resulting from mechanical surface treatment and showing tool marks 3.17 lower expected value LEV value (EL) which corresponds to the 5 %-quantile of a logarithmic normal distribution for a confidence level of 75 % 3.18 higher expected va

41、lue HEV value (EH) which corresponds to the 95 %-quantile of a logarithmic normal distribution for a confidence level of 75 % Key 1 = inner radius concave front face 2 = radius 3 = outer radius convex front face Figure 1 Diagram showing convex and concave kerbs Copyright European Committee for Stand

42、ardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 8 a) Concave kerb b) Convex kerb Key 1 = overall length 2 = overall width 3 = batter or chamfer 4 = front face Figure 2 An example of a

43、curved kerb showing the overall length and width Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1343:2012EN 1343:2012 (E) 9 4 Requirements and test methods for slabs of na

44、tural stone 4.1 Introduction 4.1.1 General Unless otherwise stated, kerbs shall be supplied in free running lengths. For curved kerbs the length is the measured visible face circumference. The manufacturer shall state the minimum and maximum working length of a kerb unit. The ends of curved kerbs sh

45、all be radial. Curved kerbs shall be identified by the radius of the vertical visible or traffic face. The overall length of a number of curved kerbs shall be measured without the joints on the edge common to the visible faces. The minimum length of curved kerbs shall be 500 mm. Nominally square arr

46、ises may have a chamfer with vertical and horizontal dimensions not exceeding 2 mm. The dimensions of larger chamfers, radiused corners and splays, when used, shall be declared by the supplier. Examples of typical kerb cross-sections are shown in Figure 3. 4.1.2 Denomination The denomination shall a

47、lways be declared in accordance with EN 12440 (meaning traditional name, petrological family, typical colour and place of origin as precisely as possible for example geo coordinates). 4.1.3 Alteration of physical properties of the natural stone If during production the natural stone kerbs have been

48、subjected to a treatment that physically alters the properties of the stone (e.g. chemical treatment, patching, or filling or other similar products for natural holes, faults or cracks), then the use of such treatment shall be stated. In addition, specimens for testing shall be representative of the product and any processes that the stone is subjected to. 4.2 Dimensions 4.2.1 Overall width and height The overall width and height as laid shall be measur