BS EN 1301-3-2008 Aluminium and aluminium alloys - Drawn wire - Tolerances on dimensions《铝和铝合金 拉制钢丝 尺寸公差》.pdf

《BS EN 1301-3-2008 Aluminium and aluminium alloys - Drawn wire - Tolerances on dimensions《铝和铝合金 拉制钢丝 尺寸公差》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1301-3-2008 Aluminium and aluminium alloys - Drawn wire - Tolerances on dimensions《铝和铝合金 拉制钢丝 尺寸公差》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN1301-3:2008ICS 77.150.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAluminium andaluminium alloys Drawn wirePart 3: Tolerances on dimensionsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 October2

2、008 BSI 2008ISBN 978 0 580 56395 9Amendments/corrigenda issued since publicationDate CommentsBS EN 1301-3:2008National forewordThis British Standard is the UK implementation of EN 1301-3:2008. Itsupersedes BS EN 1301-3:1997 which is withdrawn.The UK participation in its preparation was entrusted to

3、TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Complian

4、ce with a British Standard cannot confer immunityfrom legal obligations.BS EN 1301-3:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1301-3September 2008ICS 77.150.10 Supersedes EN 1301-3:1997 English VersionAluminium and aluminium alloys - Drawn wire - Part 3:Tolerances on dimensionsAluminium

5、 et alliages daluminium - Fil tir - Partie 3:Tolrances sur dimensionsAluminium und Aluminiumlegierungen - Gezogene Drhte -Teil 3: GrenzabmaeThis European Standard was approved by CEN on 16 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condi

6、tions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three o

7、fficial versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria

8、, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE

9、FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1301-3:2008: EBS EN 1301-3:2008EN 1301-3:2008

10、(E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Tolerances on dimensions .4 3.1 General4 3.2 Round wire .5 3.3 Square and hexagonal wire 5 3.4 Rectangular wire6 BS EN 1301-3:2008EN 1301-3:2008 (E) 3 Foreword This document (EN 1301-3:2008) has been prepared by Technical Committee C

11、EN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withd

12、rawn at the latest by March 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case

13、 when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. This document supersedes EN 1301-3:1997. Within its programme of work, Technical Committee CEN/TC 132 e

14、ntrusted CEN/TC 132/WG 4 “Wires and drawing stock“ to revise EN 1301-3:1997. Besides editorial adjustments in the text and update of normative references the following changes have been made: Foreword: amended; Clause 3: amended. EN 1301 comprises the following parts under the general title “Alumini

15、um and aluminium alloys Drawn wire“: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Tolerances on dimensions According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this

16、European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the Un

17、ited Kingdom. BS EN 1301-3:2008EN 1301-3:2008 (E) 4 1 Scope This document specifies the tolerances on dimensions of aluminium and aluminium alloy drawn wire for general engineering applications (except aeronautical applications), covering diameters, thicknesses or widths or width across flats up to

18、and including 20 mm. It applies to drawn wires, except for electrical or welding purposes. It does not apply to drawing stock. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For u

19、ndated references, the latest edition of the referenced document (including any amendments) applies. EN 1301-1, Aluminium and aluminium alloys Drawn wire Part 1: Technical conditions for inspection and delivery 3 Tolerances on dimensions 3.1 General The conditions for the sampling and the measuremen

20、t of dimensions shall be in accordance with EN 1301-1. The tolerance on dimensions of drawn wires depends on its cross section. They are specified in Tables 1 to 3. BS EN 1301-3:2008EN 1301-3:2008 (E) 5 3.2 Round wire Table 1 Total tolerances for round wire (including ovality) Specified diameter mm

21、Tolerance mm Over Up to and including General purpose wire Rivet wire - 1 0,02 0 0,031 3 0,03 0 0,043 6 0,04 0 0,056 10 0,05 0 0,0610 15 0,07 0 0,0815 18 0,09 0 0,1018 20 0,11 0 0,12The ovality, defined as the difference between the maximum and the minimum diameter measured on a same cross-section s

22、hall not exceed 50 % of the total tolerance. 3.3 Square and hexagonal wire Table 2 Tolerances for square and hexagonal wire Width across flats mm Over Up to and including Tolerance mm - 3 0,04 3 6 0,05 6 10 0,07 10 15 0,10 15 20 0,14 Deviations from the regular polygonal shape are included in the sp

23、ecified tolerances. Distortions of the cross-section due to winding or unwinding operations are not covered by this standard. BS EN 1301-3:2008EN 1301-3:2008 (E) 6 3.4 Rectangular wire Table 3 Tolerances for rectangular wire Thickness or width mm Tolerance mm Over Up to and including Thickness Width

24、 - 1 0,03 0,04 1 3 0,04 0,05 3 6 0,05 0,07 6 10 0,07 0,10 10 15 0,10 0,14 15 20 0,14 0,18 Deviations from the rectangular shape are included in the specified width tolerances. Distortions of the cross-section owing to winding or unwinding are not covered by this European Standard. BS EN 1301-3:2008T

25、his page has been intentionally left blank BS EN1301-3:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view

26、on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the qualit

27、y of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 89

28、96 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996

29、 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise r

30、equested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services

31、. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administrati

32、on. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds

33、the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or ot

34、herwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: